Pioneer PRS-D3000SPL Support Question
Pioneer PRS-D3000SPL Support Question
Find answers below for this question about Pioneer PRS-D3000SPL - Amplifier.Need a Pioneer PRS-D3000SPL manual? We have 1 online manual for this item!
Question posted by bitonkarmkar9 on September 13th, 2020
Pioneer Cdj 3000 Indian Price Plz
pinoeer cdj 3000 indian price plz
Current Answers
Related Pioneer PRS-D3000SPL Manual Pages
Owners Manual - Page 2
... 4 BFC (Beat Frequency Control) Switch 4 Power Indicator 4
Connecting the Unit 5
Connection Diagram 6 Connecting the Power Terminal 7 Connecting the Speaker Terminals 8 Setting the Gain for Synced Amplifier 9 Quick Setup of the Gain 9 Advanced Setup of the Gain 9 Connecting the Speaker Wires 9
Installation 13
Example of installation on the floor mat or on...
Owners Manual - Page 3
...abnormal condition occurs. In such a case, switch the power to the car body.
• Do not touch the amplifier with one of the same size and rating.
• To prevent ...-circuit
during connection and installation, be sure to read this PIONEER product. Before attempting operation, be sure to disconnect the negative (-) terminal of the amplifier. If both L (left) and R (right) channels ...
Owners Manual - Page 4
...of 4 V or more, adjust level to match the car stereo output level. • For synced amplifier's gain control, see the "Connecting the Speaker Wires"...car stereo (standard output of 500 mV), set to the NORMAL position. If the sound distorts when the volume is turned up , turn the gain control counter-clockwise. • When using with an RCA equipped Pioneer car stereo with this power amplifier...
Owners Manual - Page 5
... eliminate unwanted vibrations and minimize power loss.
4 BFC (Beat Frequency Control) Switch
If you hear a beat while listening to an MW/LW broadcast with your car stereo, change the BFC switch using a small standard tip screwdriver.
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO NEDERLANDS
Power Indicator
The power indicator lights when...
Owners Manual - Page 6
... injury
• Do not ground the speaker wire directly or connect a negative (-) lead wire for several speakers.
• This unit is on- Turn the car stereo off . The amplifier surface could also become hot to the touch and minor burns could result.
• Connect either of two subwoofers to the unit.
• Secure...
Owners Manual - Page 7
... positive (+) terminal of the battery is not sufficient, direct grounding should be SEPARATELY fused at the amplifier, connect the battery wire terminal of the car stereo (SYSTEM REMOTE CONTROL).
Grommet Fuse (100 A) Each amplifier must be used. Car stereo with RCA pin plugs (sold separately) The ground wires must be connected to the system remote control...
Owners Manual - Page 8
...sold separately.
Connect the wires to the terminal.
• Before connecting the wires to the car body.
• Recommended wires size (AWG: American Wire Gauge) is as follows.
Insert ... to the amplifier, connect the battery wire terminal of the amplifier to the positive (+) terminal of
compartment the vehicle
Positive (+) terminal
Fuse 100 A Each amplifier must be SEPARATELY...
Owners Manual - Page 10
... W
9 Output sin wave through this system at low out-
All synced amplifiers follow the master amplifier's settings.
put level. 2. Match the synced amplifier's output to a car stereo. Connecting the Unit
Setting the Gain for Synced Amplifier
After connecting the speaker wires, adjust each synced amplifier's gain control to the figures shown below and the next page.
Connect...
Owners Manual - Page 11
... (sold separately).
2 Ω minimum 1,000 W
FRANÇAIS
ITALIANO NEDERLANDS
2 Ω minimum 1,000 W
10
Before setting to a car stereo.
For details, see the "Connection Diagram" section. Connecting speaker wire (sold separately).
4 Ω minimum 2,000 W
Two Amplifier
• Speaker wire size must be 12 AWG minimum. • Load may be any combination of speakers...
Owners Manual - Page 12
... switch must be 4 Ω or larger. Connecting the Unit
Four Amplifier Bridged
• Speaker wire size must be 12 AWG minimum. • Load may be any combination of speakers but impedance must be in SYNC INV position. Before setting to a car stereo. Connecting wire with RCA pin plugs (sold separately). MODE SELECT switch...
Owners Manual - Page 13
..." section. Connecting wire with RCA pin plugs (sold separately).
2 Ω minimum 1,000 W
MODE SELECT switch must be in SYNC position.
Connect to a car stereo.
ENGLISH
ESPAÑOL
DEUTSCH
Four Amplifier
• Speaker wire size must be 12 AWG minimum. • Load may be any combination of speakers but impedance must be in...
Owners Manual - Page 14
... liquids due to, for installation differs with liquids due to, for installation of the car, which can be located.
2.
Insert the supplied tapping screws (4 × 18 mm) into contact with the car model and installation location. Place the amplifier where it may damage internal parts of any wire. This is important to prevent...
Owners Manual - Page 15
.... Use this unit
when an audio signal is nearly the maximum current drawn by this value when working out total current drawn by multiple power amplifiers.
14
FRANÇAIS
ITALIANO NEDERLANDS
Owners Manual - Page 86
... MEXICO, S.A. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
Published by Pioneer Corporation. de C.V. Publication de Pioneer Corporation. Copyright © 2004 by Pioneer Corporation. Printed in U.S.A. All rights reserved.
Tous droits de reproduction et de traduction réservés. LTD. 253 Alexandra Road, #04...
Similar Questions
Help No Sound
ok amp turns on blue light but no sound when radio is on
ok amp turns on blue light but no sound when radio is on
(Posted by wishfuldreamz32 3 years ago)
Connecting To A Car Battery
Can you hook this up to two TS-D1002R speakers and power it with nothing but a car battery?
Can you hook this up to two TS-D1002R speakers and power it with nothing but a car battery?
(Posted by kochdenis1 12 years ago)