Pioneer PRS-D2000SPL Support Question
Pioneer PRS-D2000SPL Support Question
Find answers below for this question about Pioneer PRS-D2000SPL - Premier Amplifier.Need a Pioneer PRS-D2000SPL manual? We have 1 online manual for this item!
Current Answers
Related Pioneer PRS-D2000SPL Manual Pages
Owner's Manual - Page 2
... the Gain properly 5
Connecting the Unit 6
Connection Diagram 7 Solderless Terminal Connections 8 Connecting the Speaker Output Terminals ...... 8 Connecting the Power Terminal 9 Setting the Gain for synced amplifier 10 Connecting the Speaker Wires 10
Installation 15
Attaching the Bass boost remote control ........ 15 Example of installation on the floor mat
or on the...
Owner's Manual - Page 3
... or the amplifier fuse blows. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body.
• Do not touch the amplifier with another ... • Confirm that no parts are connected to come into contact with liquids. In addition, the amplifier surface and the surface of greater value or rating than the original fuse. If both L (left)...
Owner's Manual - Page 4
... the screws with the bass boost control. The only time the amplifier is switched to the SYNC INV mode is when amplifiers are correct. Remove the screw and stopper after checking that connections...from MASTER, SYNC and SYNC INV. For instruction of these amplifiers in combination, set the first amplifier to MASTER, and set the remaining amplifiers to SYNC or SYNC INV according to the manner in ...
Owner's Manual - Page 5
... the power is turned up , turn the gain control counter-clockwise. • When using with an RCA equipped car stereo (standard output of 500 mV), set to match the car stereo output level. • For synced amplifier's gain control, see the "Setting the Gain for details. output of 4 V or more, adjust level to the NORMAL...
Owner's Manual - Page 6
... level: 6.5 V
Preout level: 2 V (Standard: 500 mV)
Signal waveform when outputting at high volume etc., this function will be improperly set the gain control of the amplifier to the proper position but still the sound cuts out from too much output is controlled. When you raise the gain of the...
Owner's Manual - Page 7
... unit is for example where the heater will be exceeded, causing overheating.
• Never replace the fuse with cable clamps or adhesive tape. Turn the car stereo off . The amplifier surface could also become hot to the touch and minor burns could result.
• Connect either of three subwoofers to the...
Owner's Manual - Page 8
... and the bass boost remote control with the bass boost remote control wire.
If the car stereo does not have a system remote control terminal, connect the male terminal to metal body...the wire between the fuse and the positive (+) terminal of the amplifier cannot be used for speaker connection instructions.
Car stereo with RCA pin plugs (sold separately) The ground wires must be...
Owner's Manual - Page 9
Securely fasten the wire with the terminal screws. less than 35 ft.
Connect the speaker wires to tighten and
loosen the terminal screw of the amplifier. Terminal screw
Speaker output terminal
Speaker wire
3. less than 21 ft. Expose the end of the speaker wires using nippers or a cutter by about 18 ...
Owner's Manual - Page 10
... the battery wire from the engine compartment to the interior of the vehicle.
• After making all other connections to the amplifier, connect the battery wire terminal of the amplifier to the car body.
• Recommended wires size (AWG: American Wire Gauge) is sold separately.
to 1 in.)
• System remote control wire: 14...
Owner's Manual - Page 11
... the gain control, subsonic
select switch, cut off frequency control for LPF and bass boost control on each synced amplifier's gain control. Do not
mix these amplifiers with the master amplifier, adjust the gain control on the amplifier that has been set to the NORMAL position. Advanced Setup of the Gain
Set each synced...
Owner's Manual - Page 12
... MASTER position.
The amplifier surface could also become hot to the touch and minor burns could result from 1 Ω to 8 Ω.
1 Ω to achieve a 1 Ω (or lower) bridged mode (Diagram B). For details, see the "Connection Diagram".
• Use speakers having an impedance from improper bridging. In addition, refer to a car stereo. Connecting the...
Owner's Manual - Page 13
...
4 000 W (2 Ω)
• Only use speakers having an impedance from 1 Ω to 8 Ω.
1 Ω to a car stereo. SYNC INPUT
Connecting wire with RCA pin plugs (sold separately).
1 Ω to 8 Ω 2 000 W (1 Ω)
• Use ... least 2 Ω.
ENGLISH
Two Amplifier (Ex. Bridge)
Connect to the position, remove the screw and the stopper. Before setting to a car stereo.
Owner's Manual - Page 14
... screw and the stopper.
Before setting to the position, remove the screw and the stopper. Connecting the Unit
Four Amplifier (Ex. OUTPUT
Connecting wire with RCA pin plugs (sold separately).
2 Ω to a car stereo.
For details, see the "Connection Diagram".
Before setting to the position, remove the SYNC screw and the stopper.
Connect...
Owner's Manual - Page 15
... W (1 Ω)
14
ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS
ENGLISH SYNC INPUT
SYNC OUTPUT
Connecting wire with RCA pin plugs (sold separately).
Four Amplifier
MODE SELECT switch
must be in SYNC position. Connect to a car stereo.
Owner's Manual - Page 16
... ones are not caught in the sliding mechanism of the seats, resulting in fire.
• DO NOT allow amplifier to come into contact with liquids due to, for installation differs with the car model and installation location. CAUTION
To prevent malfunction and/or injury
• To ensure proper heat dissipation of the...
Owner's Manual - Page 17
.... Screw
Terminal Cover
Tapping screw (4 mm × 18 mm)
Floor mat or chassis
Drill a 2.5 mm (1/8 in .) diameter holes at the point marked, and install the amplifier, either on the chassis
1.
Drill 2.5 mm (1/8 in .) diameter hole
Changing the Direction of badge, and then tighten the screws with a 4 mm hexagonal wrench. Align the...
Owner's Manual - Page 18
... page 2). HEAT Indicator
• This indicator lights up in red when some type of the amplifier and check the location where the amplifier is installed (see the "WARNING" section on . When this happens, immediately discontinue use of the amplifier and check the wiring (see the "WARNING" section on page 2).
Contact your dealer if...
Owner's Manual - Page 19
... filter ...Cut off frequency: 40 Hz to improvements.
*Average current drawn • The average current drawn is nearly the maximum current drawn by multiple power amplifiers.
18 Use this value when working out total current drawn by this unit
when an audio signal is input. ENGLISH
ESPAÑOL DEUTSCH FRAN...
Similar Questions
Pioneer Cdj 3000 Indian Price Plz
pinoeer cdj 3000 indian price plz
pinoeer cdj 3000 indian price plz
(Posted by bitonkarmkar9 3 years ago)
Help No Sound
ok amp turns on blue light but no sound when radio is on
ok amp turns on blue light but no sound when radio is on
(Posted by wishfuldreamz32 3 years ago)
Pioneer Gm5400t Amplifier Temperature. 125w Rms/ch 2ch.
what temperature should a pioneer gm5400t run at? used on 2 10s 200w RMS per speaker 4ohm. Not overh...
what temperature should a pioneer gm5400t run at? used on 2 10s 200w RMS per speaker 4ohm. Not overh...
(Posted by lsbjay 13 years ago)