Home » Pfaff » Sewing Machines » Pfaff synchromatic 1216

Pfaff synchromatic 1216 Support Question

Find answers below for this question about Pfaff synchromatic 1216.
Need a Pfaff synchromatic 1216 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by srinath124 on July 7th, 2019

Pfaff 1216 Foot Control Circuit Diagram Required

Pfaff 1216 foot control circuit diagram required as its VDR (voltage dependent resistor burnt) which comes after transformer. I have relaid burnt tracks & no other parts damaged - hope so.I have the foot control model value required to replace it.pfaff typae020 purchased from Dubai agent (Deira center ground floor)thanks.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by techyagent on July 29th, 2019 2:08 AM

This answer was accepted by the poster of the original question.

techyagent

Member since:
June 17th, 2014

Points: 4,799,790

1,090
points

You can download the manual from the link provided below beacuse that is the only place where you find information or diagram related to foot control.

https://www.scribd.com/document/216266949/Pfaff-1216-1217-Manual

Thanks

Techygirl

Related Pfaff synchromatic 1216 Manual Pages

Owner's Manual - Page 3

... cover 1 Cleanrng 23 Dual feed 10 Electrical connection 2 Foot control 2 Foot control receptacle 1 Light bulb 23 Machine feed 9 Master selector dial 8 Needle 13 Needle position 9 Oiling 23 Ornamental stitches 15 Overlock seam 18, 19 Presser bar lifter 10 Reverse sewing 9 Sewing feet 1 2, 1 6 Sewing mechanism 3 Slot-threading 6 Special accessories 22 Special...

Owner's Manual - Page 4

... Parts of your sewing machine 1 Take-up ever 2 Thread retainer stud 3 Eraser button 4 Top cover lid 5 Spool pins 6 Pattern start selector wheel 7 Pattern length selector wheel 8 Bobbin winder 9 Balance wheel with stop motion knob 10 Master selector dial 11 Needle position knob 1 2 Buttonhole control 1 3 Master switch 1 4 Base of portable machines 1 5 Bed cover 1 6 Sewing foot 1 7 Sewing foot...

Owner's Manual - Page 5

... lift catches B. To replace the cover, reverse this receptacle from the machine. Foot control receptacle Remove this sequence. On model 1216 place it on the bedplate, on model 1217 push it into the free arm. 1216 1217 Before you put the machine away after sewing, replace the receptacle in its origi nal position. Then lift the cover...

Owner's Manual - Page 6

The machine starts sewing. The more the pedal is now switched on and ready for sewing. Press master switch 13. Foot contre Place the Foot control under the table. Press down its pedal. EIectrica connection Push plug A into the machine socket and plug B into the wall socket. Your machine is depressed, the faster the machine vvill run.

Owner's Manual - Page 7

... bobbin winding, tighten the knob again. Hold the balance wheel steady and turn the stop motion knob toward you start winding the bobbin, disengage the sewing mechanism. Removing bobbin case and bobbin Raise the needle. The bobbin cannot fall out as long as you keep latch A raised. Lift larch A, pull out...

Owner's Manual - Page 8

Disengage the sewing mechanism. Pass the thread around thread retainer stud 2, wind it around the bobbin a few times, as indicated by the arrow. Push ever 8 against the bobbin ... bobbin Insert the filled bobbin into eye C. Place a bobbin on magnetic disc A and a spool of thread on one of the spool pins. Re-engage the sewing mechanism. Bobbin winding Raise pins 5.

Owner's Manual - Page 9

Latch A and stud B must be flush. Release the latch. Attaching the work support 1216: Turn over the foot control receptack and attach t (A). 1217: Push the workplate over the free arm until its guide pins enter the two holes (B). inserting the bobbin case Lift latch A and push the bobbin case onto stud B as tar as t will go, making sure slot C points upwards.

Owner's Manual - Page 10

Draw the thread under fingers A and 8, at the same time releasing control 19 and the thread. Then pull the thread through the needle eye. As you to raise the needle and take -up lever 1, Then pull it ... eye completely. Upper threading Pull the thread from the spool and draw it into slot A, guide B and take -up lever 1 (see drawing) Push needle threader control 19 down all the way.

Owner's Manual - Page 11

...sewing toot. Thread cutter The thread cutter is up the bobbin thread Hold the needle thread a little taut. Turn balance wheel 9 toward the back. Pull the bobbin thread out of the machine... toward you until the needle moves down and up aqain and the takeup lever is located at the hack c top feeding foot 23. Place the threads n thread cut...

Owner's Manual - Page 13

... positions: A = Normal position B = As long a-s the control is positioned below mark A. D 4 c 4 / 7- D VI Turn knob 11 until the symbol of a seam(. C = Vertical position. D = The feed dog is dropped (for backtacking the end of the needle position desired is pressed, the machine sews backwards (for embroidering, darning, etc I. The machine se permanently in the needle hole...

Owner's Manual - Page 14

... top and bottom feed) This feed mechanism prevents one ply from creeping ahead of the other. To disengage: Push the top feeding foot down until it swing up lever 1.) B = The sewing foot is raised. (Before you remove the work, turn the balance wheel toward you to raise the needle and take-up . Before...

Owner's Manual - Page 18

... combinations are listed in conjunction with ornamental-stitch button J turn pattern start selector wheel 6 to the start-of master selector dial 10/11 which is required for a specific utility stitch is indicated on pages 26-30.

Owner's Manual - Page 19

... symbol- H HE The following symbols are used on the pattern start selector wheel: OZsfl1D Ornamental stitches Buttons F to J show ornamental stitches. (They are set the machine at the beginning of the pattern can be obtained by turn ing wheel 7 in the range from 10 to 18. (When turned to set as...

Owner's Manual - Page 21

... B enters slots C. Bottom illustration: Push the darning fo over the retaining fork of foot moves along the zipper chain on the right or left position Left edge of the sewing foot. Special sewing feet Zipper (and edge stitching) foot Attach the foot offset to resemble a seam. Set the needle position accordingly. Guide the workpiece so that...

Owner's Manual - Page 23

Then press ejector lever F (bottom ill.) to one of the seam raise the sewing foot. Overlook seam The overlock stitch is used for sewing along edge guide E (top ill.). Insert the material so that its edge ... trim the threads. At the end of the two dots in range 8 the machine sews an edge-finishing seam with an edge-thread effect. Remove the work by pulling it with an edge thread ...

Owner's Manual - Page 24

... the needle thread tension by turning the master selector dial in the buttonhole range from + to 2 numbers. As you sew, arrow C moves along scale D. Turn knob ii to determine the buttonhole length (bottom ill.). Restore this setting at ...), pull it taut, and clamp it in the illustration (top). Begin by sewing a buttonhole on a piece of each button bole. Buttonhole settinq ttach the buttonhole...

Owner's Manual - Page 25

... threads. E = Sew the first buttonhole seam in the length desired. J = Cut the buttonhole open with your seam ripper, but be careful that you do not damage the bartacks and the seams. / / -I 21 Sewhiq buttonholes To afford a better view of the buttonhole foot for ward as far as the first. (For this, the machine is...

Owner's Manual - Page 26

... special sewing jobs. etc.) For edge stitching For inserting zippers For felled seams For cording and appliqué work (needle size 80. Not all the sewing feet listed below are at present available as snap-on feet, To attach a conventional sewing foot, remove the sewing foot holder. For edge stitching They can be obtained from your Pfaff...

Owner's Manual - Page 27

...Cleaning and oiling 1216: Remove cover 15. Do not oil the machine because it tovvard B. Clean the parts in slots C. ...Insert the new light bulb so that its pins move in the vicinity of oil into the hook raceway now and then. .) 0 Push it up , turn it is main tenance-free, All you have to do is put a drop of the sewing...

Owner's Manual - Page 29

... adjustment. Seam is loose. Feed dog dropped. (Reverse-feed Flick reverse-feed control to switch off the master switch. Machine works heavily Thread ends in overlock seam Overlock-stitch attachment is not uniform Tension out of fabric under the sewing foot. Check upper and lower tensions. Use first-class thread only. During bobbin winding...