Home » Pfaff » Sewing Machines » Pfaff hobbylock 776

Pfaff hobbylock 776 Support Question

Find answers below for this question about Pfaff hobbylock 776.
Need a Pfaff hobbylock 776 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by kathypartridge on June 10th, 2014

Loop Feed Needs Replacing

I am looking at a pfaff hobblock 776 and it says it needs a new loop feed unit is it repairable or advoid it ?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Pfaff hobbylock 776 Manual Pages

Owner's Manual - Page 2

... Turning on / off the amp 5 e. Operating the machine g a. d. Incorrect thread tension and how to observe during sewing 13 14 i. 3-thread overedge seam 15 D. Points to adjust 11 12 g. Some adjustment / Maintenance 15 a. Adjusting the seam width 16 b. Replacing needle (S) 18 e, Replacing the upper knife 19 f. Sewing problems and solutions Parts names 4 B. How to...

Owner's Manual - Page 5

...notthnroetnlhleecr omcnoanncenhceitncettohaersipnslthuoogwthtneo a power source. c. By switching on the machine, sewing light is switched on a flat and horizontal surface or purpose-built sewing machine table. How to run at low speed: As you press down gently, the machine will run faster. d. S. b. Turning on / off the lamp Sewing light is turned on the pedal. Preparation for...

Owner's Manual - Page 6

When oiling always be sure to the areas indicated. 5 Lubrication The bushings and other important parts are made from special materials and only require lubrication once or twice a month. Apply just one or two drops of oil to use a good quality sewing machine oil. e.

Owner's Manual - Page 7

... cover, slide the looper cover to the right, swing it to make threading easier. ff7 6 To open the side cover, push it down towards the machine until it immediately aligns above the thread reel bar pins. 4.

Owner's Manual - Page 10

... depending on the fabric and type and thickness of the upper cutter and start sewing slowly. C. Test sewing After threading, be sure to the edge of the thread and must therefore be... accordingly. Insert the cloth under the presser foot up to make a test sewing before actual operation. OPerating the machine a. Checking the threads being interlocked. 2. By refering to the chart below ...

Owner's Manual - Page 13

... For the roll hemm ng (narrow / foldover hemming) replace the normal stitch foot by the roll hemming foot. By following this instruction, very good sewing results can then be achieved. 1 .Raice the presser ...shank until connecting points are in contact, then lower the presser foot and the new foot will then be engaged. • Correct thread tension of roll hemming o 0 0 0 ...

Owner's Manual - Page 14

... can be used to observe during sewing • • PtTfhalheabecrfneiocotsthlwoebiwlelfflayobfreresiecedcwoumnatudhmteeoermnftichrasietnticgcfaeultwoltytesrseatwiant.cndhdegsl,...of the material breaking the so as to needles. h. Do not push or pull avoid the possibility of sew approximately 5 the seam then cut the thread chain. • Securing the seam: Tie the thread chain...

Owner's Manual - Page 15

.... Wide seam Use left looper thread. 3. Seam width can be changed from 5 mm to 5 mm.(Standard seam width is as usual. • For wide seam sewing. 1 Remove the right hand needle. 2. Use the right hand needle thread and right & left hand needle only. Threading procedure is 3.5 mm). Use the left hand...

Owner's Manual - Page 17

...be neccssary to experiment with your Right Hand, set the required stitch length by turning the feed regulator control dial (see illustration and at the same time set the required differential ratio, ...puck ering of seams. The ratio of the differential is that of the feed of the rear feed-dog teeth, against the feed of feed-dog teeth moving independ ently to 2.0mm. Heavy knitwear, very elastic ...

Owner's Manual - Page 18

... on the weight of fabric you . Light weight materials needing a finer needle, with a thicker needle for heavier weights. ATTENTION When replacing needles, please take note of the arrow), raising the...using Needle sizes from No.75 to the highest position. Fitting the right needle screw 17 Replacing needle (S) DURING THIS OPERATION DISCONNECT THE MAINS PLUG FROM THE POWER SOURCE. 1. slant and ...

Owner's Manual - Page 19

... to its bottom positiOn at which point the tip of needle plate (A) 18 Replacing the upper knife DURING THIS OPERATION DISCONNECT THE PLUG FROM THE MAINS OUTLET. 1. Turn...screw (A) securely, using a screwdriver, retighten the retaining screw (A) securely. Fitting a new upper knife Place the new knife onto the carrier stopper (in position by the carrier stopper (approximately horizontal to ...

Owner's Manual - Page 20

... FROM THE POWER SOURCE • Loosen the screw of the rear of the machine body and remove the lamp cover. • Turn the bulb in Insert the new direction bulb by (1) and remove it in the direction (2). Replace cover. Replacing the lower knife DURING ThIS OPERATION DISCONNECT THE PLUG FROM THE MAINS OUTLET 1FkuLl...

Owner's Manual - Page 21

... too tight Thread has caught due to time encounter the occasional problem which should operate efficiently and without difficulty. Insert new needle correctly. Insert needle correctly. Sewing problems and solutions Used correctly, your machine should overcome most of thread tensions Set thread tensions correctly. Regulate tension. position 20 Do not pull or push...