Pfaff hobbylock 776 Support and Manuals
Get Help and Manuals for this Pfaff item
View All Support Options Below
Free Pfaff hobbylock 776 manuals!
Problems with Pfaff hobbylock 776?
Ask a Question
Free Pfaff hobbylock 776 manuals!
Problems with Pfaff hobbylock 776?
Ask a Question
Most Recent Pfaff hobbylock 776 Questions
I Need A Replacement Feet For My 776.the Pin Has Broke And Is Not Holding The Fe
(Posted by lilih 2 years ago)
Tension Settings For Normal Serge
(Posted by Butterfly470179 2 years ago)
I Cannot Sew.
i woud like to regulate and fix the height of the needle bar, because this bar moove freely up and d...
i woud like to regulate and fix the height of the needle bar, because this bar moove freely up and d...
(Posted by raquelbordigoni 4 years ago)
Part For Pfaff Hobbylock 776
I need a telescopic thread reel stand bar for a Pfaff Hobbylock 776
I need a telescopic thread reel stand bar for a Pfaff Hobbylock 776
(Posted by dortmiller 5 years ago)
Needle Shaft Turns Completely Around
I have acquired a hobbyist 776 and the needle shaft the makes the needle go up and down is loose or ...
I have acquired a hobbyist 776 and the needle shaft the makes the needle go up and down is loose or ...
(Posted by dbw9968 5 years ago)
Popular Pfaff hobbylock 776 Manual Pages
Owner's Manual - Page 1
fh©EbEbyfl©©D
71
OPERATING INSTRUCTiON
Owner's Manual - Page 2
... knife
19
g. Fitting the foot controfler c. Test sewing
b. d. Roll hemming h. Sewing problems and solutions Parts names
4
B. Threading procedure
9
C. Adjusting the stitch length
16
c. Replacing the light bulb
20
F. Incorrect thread tension and how to adjust
11 12
g. Replacing needle (S)
18
e, Replacing the upper knife
19
f. CONTENTS
2
A. Preparation for...
Owner's Manual - Page 3
Parts name
o Front side Telescopic thread reel stand bar
• Rear side Pulley wheel feet
2 A.
Owner's Manual - Page 4
...8226; Accessories
Accessories case Screw driver Screw driver (For needle) Iweezers
Oiler
• Looper mechanism
• Specifications Maximum speed Overlock seam width Stitch length
Presser foot Presser foot lift Needle Number of threads Lubrication Dimentions Net weight
1 300 s.p.m. 3.5mm (standard) 1.0 - 4.0mm Hinged 5mm
130 / 705H No.75 - No.90 4 Manual 278(W) x 264(D) x 310(H) 7Kg
Brush...
Owner's Manual - Page 5
... to run at low speed: As you press down gently, the machine will run faster. d. By switching on the machine, sewing light is turned off.
4 To stop the machine, lift your foot lightly on a flat and horizontal surface or purpose-built sewing machine table. Preparation This machine must be used on the pedal.
Turning on / off the...
Owner's Manual - Page 6
When oiling always be sure to the areas indicated.
5 Apply just one or two drops of oil to use a good quality sewing machine oil. Lubrication The bushings and other important parts are made from special materials and only require lubrication once or twice a month. e.
Owner's Manual - Page 7
... you .
3.
To close securely. f. To open the side cover, push it down towards the machine until it immediately aligns above the thread reel bar pins.
4. Threading procedure
1. Position the telescopic thread guide bar so that the telescopic thread guide bar is at maximum vertical height.
2.
ff7
6 To open the looper cover, slide the...
Owner's Manual - Page 11
... thread Woolly nylon
No.80-100
Stitch length 3.Oto4.Omm 3.0 to 4. 0mm 3.0 to 4.0mm 2.0 to 4.0mm 1.0 to 1.5mm
e. Correct thread tension
Top side
10
Left needle thread Right needle thread d.
Owner's Manual - Page 13
... then push up the small lever. By following this instruction, very good sewing results can then be engaged.
• Correct thread tension of roll hemming
o
0
0
0
00
Narrow hemming 12
Top side Fold-over hemming Normal hemming toot • How to replace the presser toot
Remove the left needle first. Roll hemming
. Roll hemming foot
.
Owner's Manual - Page 15
... is possible by using either right or left hand needles. Remove the left hand needle only. Seam width can be changed from 3 mm to 7 mm. (Standard seam width is as usual. • For wide seam sewing. 1 Remove the right hand needle. 2. Use the right hand needle thread and right & left looper thread. 3. Use the left...
Owner's Manual - Page 17
... moving independ ently to 2.0mm. These can be neccssary to experiment with your Right Hand, set the required stitch length by turning the feed regulator control dial (see illustration and at the same time set the required differential ratio, by pushing away from 0.8mm to produce an even stitch formation on woven or...
Owner's Manual - Page 18
Light weight materials needing a finer needle, with a thicker needle for heavier weights.
Replacing needle (S) DURING THIS OPERATION DISCONNECT THE MAINS PLUG FROM THE POWER SOURCE.
1. The recommended needle system are using a screwdriver, re-tighten the needle clamp screw securely. Fitting the right needle
screw
17 Removing needle (s) Turn the pulley wheel towards you are : 130 ...
Owner's Manual - Page 19
... the knife will be necessary.
1.0mm
Surface of needle plate
(A)
18 It is necessary to adjust, loosen the upper knife screw (A) and raise or lower as abnve), and, using a screw driver. To remove the upper knife. Then loosen the ... against the lower knife and behind the guard on the presser foot. Replacing the upper knife
DURING THIS OPERATION DISCONNECT THE PLUG FROM THE MAINS OUTLET.
1.
Owner's Manual - Page 20
...,
turning it . Caution: Use a
maximum
1
5
watt
bulb
only.
19 Rbyepmlaecaentsheofutphpeerreklneiafseeinknitos bwo(srekeingalspoospitaiogne 17)
g. Replace cover. using a screwdriver. Replacing the light bulb
FIRST DISCONNECT ThE MAINS PLUG FROM THE POWER SOURCE • Loosen the screw of the rear of the machine
body and remove the lamp cover.
•
Turn the bulb in Insert the...
Owner's Manual - Page 21
... is not in the recommended manner. Insert needle correctly.
However you may from not carrying Out various adjustments in the working Push the presser foot lever down. Do not pull or push material during sewing. E. Sewing problems and solutions
Used correctly, your machine should overcome most of thread tensions
Set thread tensions correctly. Listed below are...
Pfaff hobbylock 776 Reviews
We have not received any reviews for Pfaff yet.