Pfaff hobbymatic 803 Support and Manuals
Get Help and Manuals for this Pfaff item
View All Support Options Below
Free Pfaff hobbymatic 803 manuals!
Problems with Pfaff hobbymatic 803?
Ask a Question
Free Pfaff hobbymatic 803 manuals!
Problems with Pfaff hobbymatic 803?
Ask a Question
Most Recent Pfaff hobbymatic 803 Questions
Hobbymatic 803 Feed Drop Mechanism Not Responding
The feed drop switch was activated and dropped the feet however I can not get the feed drop switch t...
The feed drop switch was activated and dropped the feet however I can not get the feed drop switch t...
(Posted by ntomlinson99 2 years ago)
Popular Pfaff hobbymatic 803 Manual Pages
Owner's Manual - Page 1
A
Hobbymatic 800., 801, 802, 803, 806, 807 instruction book
Owner's Manual - Page 2
..., 806 and 807 Utility stitches, models 802 to 807 Stretch stitches, models 806, 807 Thread tensions Changing the needle Reverse sewing Dropping the machine feed Changing the sewing foot Sewing feet Special sewing feet Buttonhole settings Sewing buttonholes Fitting detachable workplate Changing the light bulb Cleaning and oiling Trouble shooting
Page 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 9
10 10 11...
Owner's Manual - Page 4
...coloured brown must be connected to injure your sewing machine
1 Take-up lever 2 Thread guide 3 Bobbin tension stud
(for bobbin winding) and thread guiding hook 4 Zigzag-stitch lever 5 Utility-...code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the letter L or coloured red. Parts of your fingers on the needle during sewing...
Owner's Manual - Page 5
... original position. Before putting the machine away after sewing replace the receptacle in the slot. Foot control receptacle Remove this proce dure, making sure the bottom of the cover (G), move them back up (H) and
then remove the cover (I). J 1 Removing the carrying case cover Open the hinges on models 801, 803 and 807 push it into...
Owner's Manual - Page 6
Foot control Place the foot control on the floor under the table. The more you press down with your foot. Electrical connection Push plug G into the machine socket and plug H into the wall socket.
Your machine is now ready for sewing. The machine starts sewing. Press it down the pedal, the faster the
machine runs.
2
Owner's Manual - Page 12
The numbers indicate the length in mm.
H shows how to cut them. Thread cutter (G) The thread cutter is set the stitch length control for sewing stretch stitches on the stitch length control.
N
7
\
8 Fig. Regulating the stitch length The stitch length is an oblique slot lRoofacitashteeedtmheaatcsthehiwenienbgatocwfkoaoortfd. tPhthueellpbtrhaeecskswe. roDrbkraarwo.utthe threads...
Owner's Manual - Page 14
The utility- Selecting stretch stitches on page 11. Selecting utility stitches on
models 802 to 807 The various utility indicated by black of the stitch panel
stitches possible ... only be turned in the red sector on the machine and
explained on mTisutw(tnahtshhtiondiaeeteelddnciiecthltevgyeatlFa-rhattspetierpegeaiaed8opr.nnn)0zued.ec6iinsaglsoSrstzartagsertanrrrentregeedeitdnstct-...
Owner's Manual - Page 15
... stitch B Elastic triple zigzag stitch C Honeycomb stitch D Pullover stitch E Feather stitq\h F Overlock stitch
4
A
A
B
AAAAAAA/
C
i)\/\i\i\I\/\i I V V V VU V V
AAA
B AVAVN
C
E
F
F
I
11
Utility stitches, models 802-807 A Straight stitch B Zigzag stitch C Elastic stItch D Blindstitch E Elastic decorative stitch F Shell-edge stitch
Models 802 and 803 have utility stitches A to D.
Owner's Manual - Page 16
... freely by its own weight, but should gradually move downwards when you jerk your hand upwards lightly.
The normal tension
setting is in the white range between 3 and 5. Lower tension H = Regulating screw. J = Upper tension too loose...4
I-
1
K
12 The higher the number, the tighter the tension.
Upper tension (19) G = Setting mark. K Lower tension too loose or upper tension too tight.
Owner's Manual - Page 17
As long as you button depressed, the machine
keep sews
this
backwards. Dropping the machine feed Push drop-feed button 22 to G.
'4
GH
13
Reverse sewing Push button 12. embroidery,
darning etc.) For sewing, push the the bottom, and back
drop-feed button again to position
to The feed dog is dropped (for
position H. CRnSnsaieneyhadeedisaesddtneellpogemeutfi,...
Owner's Manual - Page 20
...Insert the filler cord as follows (Fig. J):
place it bears against its stop.
As you sew, arrow L moves along the right or left zipper chain.
Insert the pin of the foot... L. Push bracket M toward the back and hold it in groove J.
Buttonhole settings
On models 5 to B.
802
to
807
set
utility-stitch
dial
Push let it rests against screw N. This determines the buttonhole ...
Owner's Manual - Page 22
Swing the support down a little after fitting.
(Figs. Press the workplate down (Fig. G and H below left.)
Fitting the detachable workplate
on models 601, 803 and 807 Push the workplate over the free arm until it snaps into place. I) and press it to the machine so that its two guide pins enter the holes provided. Turn the...
Owner's Manual - Page 23
...
remove cover 15 803, 807: remove (Fig. Changing the Switch off the
light bulb electric current
to
the
machine. Insert the new its pins slide in front of you. G). Pull out the plug. below, left.)
Cleaning and oiling On models 800, 802, 806: (Fig. Clean round the sewing hook and the
the parts machine
fDdneraoeondpnceowo-tifftrohoeiliela...
Owner's Manual - Page 24
... or too thick. Only gujde th material lightly.
Insert new needle. Check threading. Check Needle and Thread Chart. Machine threaded improperly. Needle bent and strikes needle plate because work alone. Remedy:
Push needle up as far as it snaps...above .
When inserting the bobbin case, press against it until it will go .
Trouble shooting
Cause:
1. Thread tension too strong.
Owner's Manual - Page 25
..., do not hold thread in hook raceway.
Thread too thick, knotty or hard. Machine feeds irregularly or not at left.)
Check upper and lower tensions. Remove needle plate ...and bottom of adjustment. Flick reverse-feed control to the right.
6. Thread machine properly and check both tensions. Machine works heavily Thread ends in hand, but pass it through thread retainer stud. Use ...
Pfaff hobbymatic 803 Reviews
We have not received any reviews for Pfaff yet.