Pfaff hobbylock 776 Support Question
Pfaff hobbylock 776 Support Question
Find answers below for this question about Pfaff hobbylock 776.Need a Pfaff hobbylock 776 manual? We have 1 online manual for this item!
Question posted by janeboeshans on September 15th, 2013
Hobbylock 776 Roll Hemmer Foot
Where can you find and buy a roll hemmer foot for a hobbylock 776?
Current Answers
Related Pfaff hobbylock 776 Manual Pages
Owner's Manual - Page 2
Fitting the foot controfler c.
Roll hemming h. Adjusting the stitch length
16
c. Sewing problems and solutions CONTENTS
2
A. Lubrication Opening and
closing
looper
cover
and
side
cover
6 6
g. Operating the machine
g
a. Dial chart for thread tension adjustment Relation chart for the sewing
4
a. Preparation
4
b. Points to adjust
11 12
g. Replacing ...
Owner's Manual - Page 4
...(D) x 310(H) 7Kg
Brush for dusting
Roll hemming presser foot
Upper knife
Thread stripping discs (4 pcs.)
Li Needle
• Controller
Dust cover
3 • Accessories
Accessories case Screw driver Screw driver (For needle) Iweezers
Oiler
• Looper mechanism
• Specifications Maximum speed Overlock seam width Stitch length
Presser foot Presser foot lift Needle Number of threads...
Owner's Manual - Page 5
... run at low speed: As you press more heavily the machine will run faster. To stop the machine, lift your foot lightly on a flat and horizontal surface or purpose-built sewing machine table. Preparation This machine must be used on the pedal.
Turning on / off the lamp Sewing light is switched on and off by switching off...
Owner's Manual - Page 6
Apply just one or two drops of oil to use a good quality sewing machine oil. e. When oiling always be sure to the areas indicated.
5 Lubrication The bushings and other important parts are made from special materials and only require lubrication once or twice a month.
Owner's Manual - Page 7
... cover, push it to the direc tion of the arrow. g. Tweezers from the accessories bag will close securely. ff7
6 Ensure that it down towards the machine until it will assist you .
3.
To close side cover, push it to the right, swing it immediately aligns above the thread reel bar pins.
4. To...
Owner's Manual - Page 10
...sewing before actual operation.
Checking the threads being interlocked.
2.
Hold the 4 threads by your left hand and turn the pulley 2 or 3 turns slowly towards you in achieving the best results. Insert the cloth under the presser foot...
Spun
Spun
Broad iply
I *80
*80
*80
*80
-
3
3
10
for
Roll
Georgetteiply
-
2
3
10
hemming
9
Procedure
1. OPerating the machine
a.
Owner's Manual - Page 11
d. Relation chart for fabrics and thread stitch length
Normal hemming
Roll hemming
Fabrics Light
Organdy, light-knit fabric, Taffeta, silk,lining materials
Medium Cotton, tricot, linen, dress materials
Heavy Tweed, suit materials, denim, heavy cloth
Knit ...
Owner's Manual - Page 13
... points are in contact, then lower the presser foot and the new foot will then be achieved.
1 .Raice the presser foot and then push up the small lever. Roll hemming foot
. By following this instruction, very good sewing results can then be taken off.
2. Roll hemming
. The foot for normal sewing can be engaged.
• Correct thread tension of...
Owner's Manual - Page 14
Do not push or pull avoid the possibility of
sew approximately 5 the seam then cut the
thread chain.
•
Securing the seam: ...,efwabreraimcgsae.imn biferyotou 13
Points to observe during sewing
• •
PtTfhalheabecrfneiocotsthlwoebiwlelfflayobfreresiecedcwoumnatudhmteeoermnftichrasietnticgcfaeultwoltytesrseatwiant.cndhdegsl,oenwttheiyer
•...
Owner's Manual - Page 15
I. 3 thread overedge seam Three-thread sewing is as usual. • For wide seam sewing. 1 Remove the right hand needle. 2. Threading procedure is possible by ...3. Seam width can be changed from 5 mm to 5 mm.(Standard seam width is 5,5 mm). • For narrow seam sewing. 1.
Use the left hand needle thread and right & left hand needle only. Seam width can be changed from 3 mm to...
Owner's Manual - Page 19
... positiOn at which point
the tip of the upper knife should be brought firmly against the lower knife and behind the guard on the presser foot. Push into the right, and turn down anti-clockwise towards
you , raising the knife to a vertical position, then, by 1 .0mm. Then loosen the retaining screw...
Owner's Manual - Page 20
... it . Replace cover. Replacing the light bulb
FIRST DISCONNECT ThE MAINS PLUG FROM THE POWER SOURCE • Loosen the screw of the rear of the machine
body and remove the lamp cover.
•
Turn the bulb in Insert the new
direction bulb by
(1) and remove it in the direction (2).
Replacing the...
Owner's Manual - Page 21
Sewing problems and solutions
Used correctly, your machine should overcome most of thread tensions
Set thread tensions correctly. ... these difficulties. position
20 However you may from time to incorrect threading
Reduce thread tension Thread correctly
Sewing foot is not fed correctly
Incorrectly threaded Thread has caught
Thread tension too tight Needle not correctly inserted Incorrect...
Similar Questions
I Need A Replacement Feet For My 776.the Pin Has Broke And Is Not Holding The Fe
(Posted by lilih 2 years ago)
Part For Pfaff Hobbylock 776
I need a telescopic thread reel stand bar for a Pfaff Hobbylock 776
I need a telescopic thread reel stand bar for a Pfaff Hobbylock 776
(Posted by dortmiller 5 years ago)
Pfaff 259 Sewing Machine Won't Run With Foot Petal
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
(Posted by Aemazing 8 years ago)
Sewing Machine Is Blinking Away And Not Able To Operate
Sewing machine was sewing constantly even after I removed my foot from the pedal. I had to switch it...
Sewing machine was sewing constantly even after I removed my foot from the pedal. I had to switch it...
(Posted by kasperflindt 11 years ago)