Pfaff hobby 303 Support Question
Pfaff hobby 303 Support Question
Find answers below for this question about Pfaff hobby 303.Need a Pfaff hobby 303 manual? We have 1 online manual for this item!
Question posted by joylynnwoodruff2002 on October 5th, 2021
Who Makes The Hobby 303? What Year Were They Made? Problems With The Hobby 303
please tell me about the Hobby 303 sewing machin
Current Answers
Answer #1: Posted by SonuKumar on October 6th, 2021 12:57 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
What year was my Pfaff made?All Pfaff machines have a serial number, allowing the owner to determine what year the machine was made. For instance, machines manufactured in 1862, the first year of Pfaff machines, have 1 as their serial number.
https://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/hobby_301_303-manual-EN.PDF?ext=.pdf
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Pfaff hobby 303 Manual Pages
Owner's Manual - Page 6
...") position, then remove plug from the electrical outlet when removing covers,
lubricating, or when making any opening. 6.
Do not place in this sewing machine. Never operate this sewing machine is used or where oxygen is
being administered. 8. IMPORTANT SAFETY INSTRUCTIONS
This sewing machine is designed and manufactured for its intended use as described in . iVhen using an...
Owner's Manual - Page 7
... which is coloured blue must be fitted. Some safety rules valid for United Kingdom only
The wires in this mains lead are included in the machine.
Owner's Manual - Page 32
... posicao baixa
Fio:
Fio de coser fino
Colocar o botão no orifIcio esquerdo do botão. Lower the sewing foot (B). Wrap the stem (D) and tie oft the threads.
)
Botoés corn pe: Grandes botöes...marcado ante riormente e debaixo do suporte do botão para formar o pe (D). Sew six to a position in the left hole of the button when the hand wheel is turned. lntroduzir a aguiha...
Owner's Manual - Page 34
... rneio. The zipper foot can be pushed to
the end. B). Lower the zipper foot again, continue the seam and then sew across the end. D). 41 A
F/
/// /
/
/ /
/,
0
// //
N
Costura de fechos de correr:...que o perno da frente F tarn bern se encaixe. 0 calcador pode ser
colocado a direita. Sew about half the length of the zip at the required width. Baixar
O calcador, continuar a coser...
Owner's Manual - Page 38
...the fabric, raise the zipper foot,
open the zip, lower the zipper foot again
and finish sewing the seam.
Secure the
end of the placket. Cobcar em posicao a ado esquerdo do tim... edge along the right guiding
edge of the seam leave the needle
down in ladies' slacks:
For machine setting see page 30. Fechar o techo de correr. Urn pouco antes do tim da costura. Close...
Owner's Manual - Page 40
...Fig. Durante esta operacão o compri mento do parafuso A. Then make a few stitches in Fig. E) until the damaged spot is resting on screw shank C. E). D, rounding the end of each line. fixar o calcador para cerzir. N.. *4% *4 %*. 'S
*4% *4*4 *4% "
D
Darning:
Preparing the machine:
Sewing foot:
Darning foot (special
accessory)
Stitch type:
Straight stitch
Needle position...
Owner's Manual - Page 47
...
Suitable for
Medium-wide cording
Wide cording Extra wide cording Extra-wide cording
Decorative designs sewn with twin needles Before you start sewing, turn the handwheel and check to make sure the needles stitch into the
fabric properly.
In this way, needle breakage can be largely prevented.
Stitch length
130/705 H-ZWJ...
Owner's Manual - Page 54
...up as far as it will go . See Needle Chart. Use first-class thread only. Machine threaded improperly. Needle thread breaks For any of material. Insert new needle.
Thread tension too ...strikes needle plate because work alone.
Insert system 130/705 H needle. Check threading. Thread machine properly and check both tensions.
50 Needle bent or blunt. See par. 1 above reasons....
Owner's Manual - Page 55
Cause:
Remedy:
5. rows of fabric under a short while, be sure
the to
sewing
switch off
the master switch.
If
run you
a threaded machine unless have to the left.
6.
Machine runs with difficulty Thread ends in hook raceway. Important notes:
Never foot.
Machine feeds irregularly or not at right.)
Flick drop-feed control to leave the...
Owner's Manual - Page 62
... foot
Overlock foot
93-035946-91
------
93-035948-91
For felled seams
98-694411-00 For sewing buttonholes
93-035 998-91 For shirring valances
93-035915-91 98-620404-00
For single-needle cording...
For cording work (needle size 80, for fine cording needle size 70)
93-035943-91 For sewing fringes and for basting
98-802 422-00 For top-stitching lwadding)
Straight-stitch foot with round needle...
Owner's Manual - Page 63
...tension Checking the needle thread tension
Thread cutter
Setting the stitch length
Reverse sewing
Stitch pattern knob
Stitch pattern table
Changing the needle
Dropping the feed Changing the sewing foot
Sewing feet Accessory compartment
Top-stitching
Elastic blind stitch
Sewing buttonholes
Sewing on buttons
Inserting zippers Seam-like zipper closures
Zippers in ladies' slacks
Darning...
Similar Questions
Pfaff 145 Tension Problem
I have a Pfaff 145 and the tension does not operate properly. I bought a new tension assembly but th...
I have a Pfaff 145 and the tension does not operate properly. I bought a new tension assembly but th...
(Posted by daletuberville 3 years ago)
How Do I Fix The Tension For Zigzag On The Hobby 303?
I bought a Hobby 303 used. I cleaned up up, oiled it. Downloaded the manual because treading it was ...
I bought a Hobby 303 used. I cleaned up up, oiled it. Downloaded the manual because treading it was ...
(Posted by cjmontowski 8 years ago)
Where Can I Find Spool Pins For My Pfaff Hobby 303?!?
(Posted by apcolliflower 9 years ago)
Sewing Backwards Now
I got my machine going forward, then backward and now, it will NOT go forward.
I got my machine going forward, then backward and now, it will NOT go forward.
(Posted by jcollins3782 9 years ago)