Oreck XL 2600HH Support Question
Oreck XL 2600HH Support Question
Find answers below for this question about Oreck XL 2600HH.Need a Oreck XL 2600HH manual? We have 2 online manuals for this item!
Question posted by wrocklaw on September 29th, 2012
Oreck Xl2600hl Hard To Push
My vacuum is hard to push. I have replaced the belt and there are no obstructions to the brush. There is no height adjustment on this model. What do you think it is?
Current Answers
Related Oreck XL 2600HH Manual Pages
Owners Guide - Page 1
... REV A
S I M P LY
A M A Z I N G®
FRANÇAIS
GUIDE D'UTILISATION PAGE 8
E S PA Ñ O L
GUIA DEL USUARIO PAGE 14
USER'S GUIDE
XL2600HH XL2610HH XL2700HH XL2700RH
HIGH SPEED UPRIGHT VACUUM CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLETÀ Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis •...
Owners Guide - Page 2
...
Please specify the model number and serial/code number which can be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER
WARNING
To ...Replace Filter Dust Bag page 5 How to Replace a Worn Belt, Stuffing or Blockage page 6 Using an Oreck Fresh Air® Tab, Bulb Replacement, To Adjust or Replace Brush page 7
Maintenance and Customer Service
Your Oreck vacuum...
Owners Guide - Page 3
...ORECK or an ORECK Authorized Retail Dealer for this limited warranty.
Brush is not even at each end. Bag tube clogged. Clear obstruction. Revolving brush...• Does the brush turn freely?
ORECK does not authorize any other source, your model and serial number from ...not extend beyond baseplate. Impeller fan is broken or Replace belt. SAVE SERVICE CALLS...CHECK THESE FIRST: •...
Owners Guide - Page 4
...be removed from the
connector assembly. REPLACE THE BELT EVERY 6 MONTHS. 7. DO NOT run the vacuum cleaner over
matching section of the... and press the On(l) -
Operating Recommendations This new ORECK XL High-Speed Upright is recommended that these be porous enough...6. Damage caused by changing the bag often. The revolving brush could damage the cord. This will guide you in performing...
Owners Guide - Page 5
... will close automatically
BAG INSTALLATION: 1. Dust seal will hinge downward.
2.
Firmly push bag dock door with warm water, and air dry. When buying replacement belts, use ONLY ORECK genuine belts. Using belts other than genuine ORECK disposable bags will affect the cleaning ability of the revolving brush and is important the inside out, with both thumbs on concrete...
Owners Guide - Page 6
...brush pulley and roll the belt around the pulley. If tube is properly seated behind the belt retainer. Make sure O-ring is not cross threaded on tube, and replace if damaged.
If your vacuum...or block the intake tube and the lower tube assembly. See illustration D. Then reinsert tube and push down screw.
Remove the door by first lining up .
A
Intake Opening
±
B
...
Owners Guide - Page 7
... rotating bearings, make sure both bearings must be adjusted.
Using A Fresh Air® Tab
Your ORECK XL vacuum cleaner has a special FRESH AIR tab pocket.
...belt and brush roll from electrical outlet before servicing. When rotating, both bearing assembly settings are the same and face up when replacing the brush roll. If a previous adjustment has already been made and bristle height...
Parts Diagram - Page 3
... Type 1, 2 & 3 Units Only O-030045502
Cord Retainer, Square Type 4, 5 & 6 Units Only
O-030049401
34 Motor Assembly Kit
O-017-0020
35 Motor Seal
O-010-7716
36 Kit, Motor Brush (Large & Small) / Spring
O-7526301
7 Pk.
1b XL2600HH / XL2610HH: Handle Assembly, includes items #38, #53, #54, #55, #56, #57, #59 Type 1, 2, 3, 4 & 5 Units Only XL2700HH / XL2700RH: Handle...
Parts Diagram - Page 4
...
Order #
39 Drive Belt, (3 Pk.)
O-030-0604
39a Drive Belt, Single
O-010-0604
40 XL2600HH / XL2610HH: Door Belt, Gray
O-7505701436
XL2700HH / XL2700RH: Door Belt, Black
O-7505701327
42 Brush Roll, Plastic Pulley
O-016...use w/#4a or order #83)
O-7558210438
User's Manual
75416-05
Magnet Clean Vacuum Protector
MC4BK
79 Stiffener (uses same length screws, notched)
O-7518902
Stiffener, ...
Similar Questions
Oreck Xl2635 Hard To Push
Why All Of A Sudden Is My Oreck Xl2635rhpk Hard To Push. I Have Replaced The Drive Belt, Removed The...
Why All Of A Sudden Is My Oreck Xl2635rhpk Hard To Push. I Have Replaced The Drive Belt, Removed The...
(Posted by whoggard 9 years ago)
Oreck Xl Model Rxl 2600 Hh- How Do U Adjust Levels On Carpet
(Posted by pbresney 10 years ago)
My 2600hh Sparks On The Armature. Will New Brushes Stop This.
The old brush's don't look bad and motor runs.
The old brush's don't look bad and motor runs.
(Posted by jmyers3940 11 years ago)
Replacement Parts
I have purchased a Oreck Orbiter XL where do i get replacement/extra pads/brushes/parts for it
I have purchased a Oreck Orbiter XL where do i get replacement/extra pads/brushes/parts for it
(Posted by kentoapparel 11 years ago)
Oreck Xl Owners Manual
wiring diagram for oreck xl upright vacuum cleaner
wiring diagram for oreck xl upright vacuum cleaner
(Posted by joerock 12 years ago)