Oreck UPRO14T Support Question
Oreck UPRO14T Support Question
Find answers below for this question about Oreck UPRO14T.Need a Oreck UPRO14T manual? We have 1 online manual for this item!
Question posted by JSIA3 on June 4th, 2013
Roller Brush Problem
Hi, I received oreck upro14T by shipment. Put it together-double-checked did it right-looked good. Went to turn it on-put it in #2 carpet position-roller brush turned a few times then quit! Did this in any position and carpet level #.!Troubleshooted for the roller brush problem as manuel suggested-still same problem!
Current Answers
Related Oreck UPRO14T Manual Pages
Owners Guide - Page 1
Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis
USA & Canada: 1-800-989-4244 www.oreck.com 40337-02 REV A
S I M P L Y A M A Z I N G®
USER'S GUIDE
PROFESSIONAL GRADE
COMMERCIAL
UPRO14T
•IMPORTANT•
SAVE THIS BOOKLET!
Owners Guide - Page 2
...Brush page 6
BEFORE OPERATING CLEANER, READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY. It must be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM...assembly in place. • Turn off by pulling on stairs...codes and ordinances. Check with wet hands. ... Customer Service
Your Oreck vacuum cleaner is connected ... If not, have problems with appliance. Keep cord...
Owners Guide - Page 3
...-install wand.
PROBLEM
VACUUM MOTOR IS OFF
BRUSH MOTOR IS OFF
RED LIGHT ON RED & GREEN LIGHT ON FULL BAG INDICATOR FLASHES
LOW SUCTION POOR PICK UP
POSSIBLE SOURCE
Not plugged in upright position. Sensor temperature too high.
Be sure plug is found to be limited to commercial use. Warranty
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company...
Owners Guide - Page 4
... install cord strain relief (22), hold power cord 7-8 inches from plug. Wand
3. Dusting Brush
12. Position the open end of wand over the top of the pigtail on the cord strain relief and pull excess until it snaps into the top of your vacuum, the parts have been numbered as follows:
1. Brush Housing
22.
Owners Guide - Page 5
... far as described in the "Upright Carpet Vacuum Cleaning".
3.
Although your upright will turn (fig 5).
4. Change the disposable filter dust bag at the vacuum motor inlet weekly.
3. 2
3
... and OPEN THE BAG.
2. This will start turning (fig 6).
5. Keep machine in the "OFF" position. Check brush area for any time the vacuum cleaner does not pick up pins, paper clips,...
Owners Guide - Page 6
.... Electronic Brush Alert
The vacuum cleaner is equipped with the ORECK vacuum cleaner. OPERATION GUIDE NORMAL OPERATION BELT BROKEN RED BLINKING BRUSH BLOCKED
Red Light - When the temperature gets too high the sensor shuts off the vacuum motor.
The purpose of the paper bag is sensed at maximum efficiency, change the dust bag frequently.
The roller brush may...
Owners Guide - Page 8
All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC.
40337-02 REV A 05/06
ECN# R-8370 All rights reserved. ©2006 Oreck Holdings, LLC.
Similar Questions
Brush Removal On Oreck Orbiter
It seems as though I'm not strong enough to pull the brush attachment off my Orbiter, and I'm not a ...
It seems as though I'm not strong enough to pull the brush attachment off my Orbiter, and I'm not a ...
(Posted by timber15651 1 year ago)
Brush Does Not Rotate
the brush at base of vacuum is not rotating at all and motor smells like it is bu
the brush at base of vacuum is not rotating at all and motor smells like it is bu
(Posted by Ronsellers1946 5 years ago)
What Is The Part Number For The Roller Brush. Is There A Parts Manual Available
(Posted by josephpcallaghan 9 years ago)
Oreck Dtx1400 Brush Roller
I have excessive hair on the ENDS of the brush roller. How do I get brush roller off vacuum to remov...
I have excessive hair on the ENDS of the brush roller. How do I get brush roller off vacuum to remov...
(Posted by donnabrhodes 9 years ago)
