Oreck UPRO14T Support Question
Oreck UPRO14T Support Question
Find answers below for this question about Oreck UPRO14T.Need a Oreck UPRO14T manual? We have 1 online manual for this item!
Question posted by Joannb5610 on September 21st, 2014
How Do You Change The Belt?
Do not know how to take apart to change the belt.
Current Answers
Related Oreck UPRO14T Manual Pages
Owners Guide - Page 1
Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis
USA & Canada: 1-800-989-4244 www.oreck.com 40337-02 REV A
S I M P L Y A M A Z I N G®
USER'S GUIDE
PROFESSIONAL GRADE
COMMERCIAL
UPRO14T
•IMPORTANT•
SAVE THIS BOOKLET!
Owners Guide - Page 2
.... • Connect to a properly grounded outlet only.
Maintenance and Customer Service
Your Oreck vacuum cleaner is present. • Do not pick up toxic material such as your sales or...return it should not be used as described in this appliance. • Use caution when vacuuming over cord. • Do not unplug by a qualified electrician. Use only manufacturer's
recommended...
Owners Guide - Page 3
...Authorized Service Center. Oreck shall not be sure to the original purchaser, any defects. PROBLEM
VACUUM MOTOR IS OFF
BRUSH MOTOR IS OFF
RED LIGHT ON RED & GREEN LIGHT ON FULL... only if it was originally purchased for air obstruction.
No electricity in upright position. Brush drive belt broken.
Not plugged in material or workmanship within one (1) year. Check for commercial use this...
Owners Guide - Page 4
...Latch
18. Power Brush
23. Install and tighten with power cord attached to the back of your vacuum, the parts have been numbered as follows:
1. Plug the Cord Pigtail (lower power cord) ...6. Slide cord restraint (23) 4
24 9
25
19 26
over the opening in the back of the vacuum housing. To install cord strain relief (22), hold power cord 7-8 inches from plug. Carefully slide power cord ...
Owners Guide - Page 5
... may be removed from turning) and hang it will stop automatically when the wand is not full! Change the disposable filter dust bag at the machine side to prevent cord from the floor before you vacuum.
Replace bag if needed.
2. Dust Bag Full Indicator
1. Always install a new dust bag directly after removing...
Owners Guide - Page 6
...of the brush extension.
3. Remove the filter and clean by changing the bag often. CAUTION: Do not operate the vacuum without the inlet filter in the retainer and snap into place....5. OPERATION GUIDE NORMAL OPERATION BELT BROKEN RED BLINKING BRUSH BLOCKED
Red Light - Green Light -
When the temperature gets too high the sensor shuts off the vacuum motor. Inspect the machine for...
Similar Questions
Changing The Belt
How do I change my belt? I can not find any screws on the housing. I have an ORECK XL EDGE
How do I change my belt? I can not find any screws on the housing. I have an ORECK XL EDGE
(Posted by racanell 9 years ago)
How Do I Change The Belt ? It Is Not Like Other Orecks.
(Posted by Bsowenspraise 10 years ago)
Oreck Xl Model Rxl 2600 Hh- How Do U Adjust Levels On Carpet
(Posted by pbresney 10 years ago)
Roller Brush Problem
Hi, I received oreck upro14T by shipment. Put it together-double-checked did it right-looked good. W...
Hi, I received oreck upro14T by shipment. Put it together-double-checked did it right-looked good. W...
(Posted by JSIA3 10 years ago)
Brush Belt Replacement
I am looking for belt for MODEL UV-ST-3290. THANK YOU
I am looking for belt for MODEL UV-ST-3290. THANK YOU
(Posted by bbentz44 11 years ago)