Home » Maytag » Laundry Washers » Maytag MVWC200XW

Maytag MVWC200XW Support Question

Find answers below for this question about Maytag MVWC200XW.
Need a Maytag MVWC200XW manual? We have 3 online manuals for this item!

Maytag Overview Questions Manuals Reviews Videos Research

Question posted by wilkins2340 on November 26th, 2012

The Lid Lock Continously Clicks Without Locking And Starting The Machine. Why?

The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Maytag MVWC200XW Manual Pages

Installation Instructions - Page 2

... Pliers that open to toll-free phone numbers on back page of the washer. n 8212656RP n 8212641RP n 8212646RP n 8212545RP n 8212487RP n 8212638RP ...Not supplied with flat washers To order, please refer to 19⁄...washer to toll-free numbers on back page of your washer...clamp Inlet hoses with washer) Your installation may... insert in a basement, laundry room, closet, or recessed...

Installation Instructions - Page 3

...). n A grounded electrical outlet located within 3 ft (0.9 m) of hot and cold water fill valves on washer, and water pressure of washer. n A level floor with beaded tie strap. 3 n Floor must install higher than 4.5" (113 mm) of standpipe must be needed.) Laundry tub drain system Minimum capacity: 20 gal. (76 L). Top of drain hose should be...

Installation Instructions - Page 4

... not sure the washer is properly grounded. If your washer includes a sound shield, please refer to the instructions included with a qualified electrician if you start: remove shipping materials...a separate ground wire is used, it and make sure lid is required. n Do not have a fuse in the neutral or ground circuit. 48" (1.2 m) Move washer to within 4 ft (1.2 m) of the customer to a...

Installation Instructions - Page 5

... hose form as shown. Free power cord If clamp is not already in place on bottom of laundry tub. NOTE: Keep tray in Step 7. You may need to drain port Remove tape from washer lid, open lid and remove cardboard packing tray from tray. IMPORTANT: 4.5" (113 mm) of drain hose, slide it over end...

Installation Instructions - Page 6

You may enter washer. Connect inlet hoses to water faucets Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to tighten couplings an additional two... with cold water inlet valve. NOTE: Both hoses must be connected to faucets or washer. Connect inlet hoses to washer Attach hose to inlet valves. IMPORTANT: Do not overtighten or use tape or sealants on...

Installation Instructions - Page 7

... 14 mm open -end or adjustable wrench to turn the leveling foot clockwise to lower the washer or counterclockwise to step 14. When washer is level, skip to raise the washer. HELPFUL TIP: You may want to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with floor. Not Level LEVEL Not...

Installation Instructions - Page 8

...outlet. Select any tape remaining on . q Check that you have all packaging materials. Start washer and allow to see what was skipped. q Check that yellow shipping materials were completely removed...and any cycle. q Check that all parts are on washer. q Check that water faucets are now installed. Close lid. q Check that washer is an extra part, go back through steps to ...

Owners Manual - Page 2

WASHER SAFETY 2

Owners Manual - Page 3

...START/Pause/Unlock button is spinning, it may vary. 1 WATER LEVEL Select the setting most suitable for your laundry load. NOTE: If the washer is pressed, the washer will first perform a self-test on the lid lock... level. You will hear a click, and the lid will continue to cancel a cycle. After draining and spinning out wash water, the washer will unlock briefly before filling. Small...

Owners Manual - Page 4

...fabrics Normal Regular Normal Light No-iron fabrics, cottons, perm press, linens, synthetics Machine-wash silks, lingerie, washable wools Swimsuits and items requiring rinsing without detergent Dripping wet..., and blends. SPIN LID LOCKED The washer spins the load at high speed. Not all models. Place small items in mesh garment bags before washing. Press START/Pause/ Unlock again to...

Owners Manual - Page 5

...help avoid tangling when washing delicate or small items. • Turn knits inside out to your laundry 2. Synthetics, knits, and corduroy fabrics will pick up lint from lint-givers. IMPORTANT: Follow ...8226; Mend rips and tears to avoid further damage to determine the amount of the washer basket before adding clothes. Separate lint-takers from towels, rugs, and chenille fabrics. ...

Owners Manual - Page 6

Load laundry into washer. Items need to move freely for correct amount of the rim. Add liquid chlorine bleach to reduce...For best results, do not pack the load tightly. IMPORTANT: Do not tightly pack or force items into washer 5. Close the lid and press the START/Pause/ Unlock button again to reduce tangling. Turn cycle knob to ensure proper distribution of the fabric softener ...

Owners Manual - Page 7

... Items need to open for load unbalance. Then close lid and press START/ Pause/Unlock again to move freely. 8. If lid is delayed for 2 to 3 minutes to help dissolve ...detergent. Bright colors Moderate to assist in soil removal and to check for more than what your previous washer...

Owners Manual - Page 8

..., damp cloth. Rinse dispenser under warm water, then replace it will continue. Press and hold the START/Pause/Unlock for a moment and pause, lid will lock, then cycle will not freeze. NOTE: To avoid damage to the washer or clothing, do not wash clothes with thumbs. 2. To clean exterior: 1. Use a soft, damp cloth or...

Owners Manual - Page 9

... water inlet hoses. 2. Unplug power cord. 5. Drape power cord over lid and down front of washer. Reconnect water inlet hoses. TRANSPORTING YOUR WASHER 1. If washer will be moved during freezing weather, follow Winter Storage Care directions before moving : 1. Keep lid taped until washer is placed in washer or reconnect power. 3. Refer to "Installation Instructions" to clean...

Owners Manual - Page 10

...Washer" in washer drain system. Clicking or metallic noises Objects caught in this Use and Care Guide. Loose items such as final amounts of plywood under your washer...on (indicating that the washer was unable to fill appropriately) Check for leaks (laundry tubs, drain pipe, ...started the washer. Both hoses must be in firm contact with the floor and locked. Gurgling or humming Washer...

Owners Manual - Page 11

... only HE detergent. Replace any clogs from drain hose. Do not interrupt cycle. Close lid and press START/Pause/Unlock. Do not add more than cycles with a low spin speed. Use the...several items, rearrange load evenly in the load, select Drain & Spin. Washer will pause during certain phases of a service call...In U.S.A. Washer spins the dry load for small items. Use a cycle with high spin...

Owners Manual - Page 12

... air flow during the final spin. Sand, pet hair, lint, etc. however, items will be on washer may require additional rinsing. Add only 1 or 2 garments after washer has started . See the "Cycle Guide" to match your previous washer. Reduce tangling by mixing types of garments being washed. Load garments in the inlet hose. Choose...

Owners Manual - Page 13

... avoid the cost of bleach dispenser when loading and unloading washer. Not using the Start/Pause button. Load dispensers before starting wash load. Do not add products directly onto load. Fabric... can keep washer from too much detergent. Load garments in Washer Maintenance. Do not place load items on load size and soil level. Lid locked light is flashing The lid is not closed...

Owners Manual - Page 14

... you specific legal rights, and you . Proof of original purchase date is inconsistent to published user or operator instructions and/or installation instructions. 2. MAYTAG® LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or...

Maytag Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Not filling or not starting - Load-sensing Energy Star top-load washer with agitator.
... to 6 seconds after the cycle started . Load-sensing Energy Star top-load washer with water when I start the washer. If the lid was opened after you using an extension cord? Is the washer lid closed . Close the washer lid. Pull out the cycle control knob to start the washer. Filling will not start if the pointer is...
Washer will not fill or start - Top-load HE washer with Dispenser Drawer - video
... washer with agitator. Washer will unlock briefly before locking again. You will hear a click, the basket will make a slight turn on a fuse box, check to see if a fuse has blown and replace it, if necessary. If the problem continues to the load once the washer started . Next, the washer will first perform a self-test on the lid lock...
Washer is not cleaning laundry - Top-load HE washer with Dispenser Drawer - video
...Start button is connected to the hot-water faucet and that require cold-water rinses. This process may need to install an iron filter. Detergent works by attaching to soils and carrying them a dingy appearance. Washer is not cleaning laundry... Why is on the lid lock. You will hear a click, the basket will first perform a self-test on . Washer is connected to the ...