Maytag MVWC200XW Support Question
Maytag MVWC200XW Support Question
Find answers below for this question about Maytag MVWC200XW.Need a Maytag MVWC200XW manual? We have 3 online manuals for this item!
Question posted by hehly on January 4th, 2014
Lid Lock Light Flashes On My Mvwc200xw And It Will Not Run
The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Maytag MVWC200XW Manual Pages
Installation Instructions - Page 2
...)
1" (25 mm) standpipe
2" (51 mm) diameter to improve performance and minimize noise and possible "washer walk".
Install your washer to 1" (25 mm) diameter Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835
Drain hose too... for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" (1067 mm)
2...
Installation Instructions - Page 3
... companion appliances and clearances for a standpipe drain: 2" (51 mm). Water remaining in washer after use may cause damage in your Use and Care Guide. If you must support washer's total weight (with maximum slope of washer. (Additional hoses may be needed.)
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Consider allowing more than...
Installation Instructions - Page 4
...the properly grounded outlet installed by a qualified electrician. NOTE: To avoid floor damage, set washer onto cardboard before moving it at this appliance be plugged into a mating, 3 prong, ...washer upright. or 20-amp, fused electrical supply is taped shut.
2. n This washer is necessary for proper operation and to within 4 ft (1.2 m) of the customer to install it and make sure lid...
Installation Instructions - Page 5
... to allow free access to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from tub
Connect Drain Hose
...5.
For a floor drain, remove the preinstalled drain hose form as shown.
Attach drain hose to back of washer.
4.5" (113 mm)
Place hose into standpipe or lay on elbow end of laundry...
Installation Instructions - Page 6
... use old hoses. Connect inlet hoses to washer correctly. Repeat this step with separate directions.
IMPORTANT: To reduce risk of which hose is connected to hot water to help in attaching hoses to water faucets
Run water for cold water faucet. n Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or...
Installation Instructions - Page 7
... strap.
Check levelness of sides. Rock washer back and forth to step 14. HELPFUL TIP: You may want to laundry tub leg, drain standpipe, or inlet ...washer cabinet.
Adjust leveling feet
Jam nut
Secure drain hose to prop washer with floor. Use side seam as shown. HELPFUL TIP: You may want to check levelness of front using lid, as a guide to prop up front of washer...
Installation Instructions - Page 8
... outlet. q Check for leaks around faucets and inlet hoses. q Check that washer is an extra part, go back through steps to complete full cycle.
8 Close lid.
q Check that you have all packaging materials. q Remove protective film from back of washer. Start washer and allow to see what was skipped.
16.
q To test and clean...
Owners Manual - Page 2
WASHER SAFETY
2
Owners Manual - Page 3
... for your load. It ensures that are available on the lid lock mechanism. NOTE: If the washer is determined by regulating incoming hot and cold water.
Fabric ...LIGHTS
The Cycle Status Lights show the progress of water for the entire rinse time.
3 Press and hold for your laundry load. You may be cooler than what your washer. After draining and spinning out wash water, the washer...
Owners Manual - Page 4
... or mixed fabric loads. To allow for loads that best fits the load being washed. Also use for proper spin operation, the lid will lock and the Lid Lock light will unlock once the washer movement has stopped.
Large items such as sport shirts, blouses, casual business clothes, permanent
press, and blends. DONE
Once the cycle...
Owners Manual - Page 5
...lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if stains remain after washing, because heat can set stains into the bottom of the washer...Follow the manufacturer's instructions to your laundry
2.
NOTE: Always read and follow fabric care label instructions to avoid damage to determine the amount of the washer basket, as well.
Add detergent...
Owners Manual - Page 6
..., splash, drip, or run into washer. Do not allow liquid fabric...lid and add the measured recommended amount ... Close the lid and press... the underside of liquid fabric softener into washer
5. Items need to reduce wrinkling and ...mL).
Turn cycle knob to start the washer.
always follow manufacturer's directions for best ...washer has completed filling, press the...to pause the washer.
Do not ...
Owners Manual - Page 7
... cooler than what your load. the lid will be added, so this will unlock once the washer movement has stopped. Select OPTION (on your previous washer provided. Press START/Pause/Unlock to begin...to open for more than your load.
Unlocking the lid to add garments If you are cold. Bright colors Moderate to light soils
Cool Warm water may take several minutes while load...
Owners Manual - Page 8
... products.
8 If cycle must be interrupted, press START/Pause/Unlock twice and run washer on the label with a permanent marker. Press and hold the START/Pause/Unlock for a moment and pause, lid will lock, then cycle will continue. NOTE: To avoid damage to the washer or clothing, do not wash clothes with thumbs.
2.
CLEANING YOUR...
Owners Manual - Page 9
Disconnect and drain water inlet hoses.
2. Unplug power cord.
5. Close lid and place tape over edge and into washer basket.
7. Before using again, run washer through Casual cycle to locate, level, and connect washer.
2. Reconnect water inlet hoses. Plug in new location. Disconnect drain from back of washer.
4. Disconnect drain hose from drain system and drain any...
Owners Manual - Page 10
... to remove items.
It is added to fill appropriately)
Check for oversized, non-absorbent items such as recommended.
Washer not performing as expected
Washer won't run or fill, washer stops working or wash light remains on clothing such as coins could unbalance washer.
Check that load is normal. Check for leaks or clogged sink or drain.
Owners Manual - Page 11
... spin light remains on (indicating that the washer was unable to pump out water within 10 minutes
Empty pockets and use an extension cord.
Reset a tripped circuit breaker. Lid must... washer to run or fill, washer stops working or wash light remains on (indicating that the washer was unable to fill appropriately) (cont.)
Check proper electrical supply. Do not interrupt cycle. Washer ...
Owners Manual - Page 12
... a load size (water level) that matches the load being washed. See "Using Your Washer" section.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs ...maytag.com/help - In Canada www.maytag.ca
If you experience
Possible causes
Solution
Washer not performing as recommended. Incorrect or wrong wash or rinse temperatures
Check for proper...
Owners Manual - Page 13
... label
been followed. Lid locked light is flashing
The lid is started.
Not using fabric softener.
Items may take several minutes if washing large loads or heavy fabrics.
13 Load garments in the bleach dispenser.
Undiluted bleach will not unlock until the basket has stopped spinning.
See "Cleaning your Washer" section.
The lid will damage fabrics. This...
Owners Manual - Page 14
...your major appliance to better help can find this book and your sales slip together for inwarranty service. MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according... specific legal rights, and you also may not apply to repair or replace appliance light bulbs, air filters or water filters.
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How do I open the lid?- Top-Load HE with Dispenser Drawer
... the Power button to turn the washer on. This will unlock once washer movement has has stopped. Top-load washer with Dispenser Drawer - Front-load washer Vibration - This may lock during transport. Under certain conditions, the lid may take several minutes if the load is flashing - Wait until the lid lock light turns off . Top Load HE with... -
Lid lock light is flashing - Top Load HE with Dispenser Drawer
... not fill or start or fill with Dispenser Drawer The lid lock light is flashing - Top-load washer with Dispenser Drawer - Is the lid closed? Top-load HE washer with Dispensers in Corners The door will not start - Close the lid. The washer will not open . The washer may take several minutes if washing a large or heavy fabrics... -
Wash light remains on - Top-load HE washer with Dispenser Drawer
... break the suction. The Wash light is on and I do? Turn on ? The washer will keep water from the floor.) If the drain is below 39" (99 cm), the water will provide the correct length of the drainpipe covered in Corners Lid lock light is complete. Turn off the water...
Similar Questions
How To Fix Lid Lock Problem On Maytag Washer Model Mvwc200xw2
(Posted by briamat 9 years ago)
Why Does Lid Lock Light Flash On Bravo Maytag Washer
(Posted by malaokpat 10 years ago)
Why Is The Sensing Light And The Lid Lock Light Flashing On My Maytag Washer
(Posted by chucktop 10 years ago)
The Lid Lock Continously Clicks Without Locking And Starting The Machine. Why?
(Posted by wilkins2340 11 years ago)