LiftMaster MEGA ARM / MEGA ARM TOWER Support Question
LiftMaster MEGA ARM / MEGA ARM TOWER Support Question
Find answers below for this question about LiftMaster MEGA ARM / MEGA ARM TOWER.Need a LiftMaster MEGA ARM / MEGA ARM TOWER manual? We have 1 online manual for this item!
Question posted by maintenance38060 on June 28th, 2012
Installing Loop Detector On Control Board Of Liftmaster
Model: MAT-DC-BB3
Serienr: 0911N8156
Mega Arm Tower
We are having problems with installing our new Mega Arm Tower.
We need the wiring diagram of how to connect the reciever and the transmittor and MVP-D-TEK Vehicle Loop Detector on the Controlboard for a single arm operation.
Looking forward to your responds,
Kind regards,
Jos Duursma
Current Answers
Answer #1: Posted by emisemis on June 28th, 2012 12:01 PM
emisemis
Member since:
June 28th, 2012 Points: 1,130
Member since:
June 28th, 2012 Points: 1,130
Related LiftMaster MEGA ARM / MEGA ARM TOWER Manual Pages
MATDCBB Green Control Board V.6.4 or newer Manual - Page 1
..., Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196
www.liftmaster.com
Mega ARM Tower
Models:
MADCBB, MATDCBB, MASDCBB & MASTDCBB
(MEGA ARM, MEGA ARM TOWER, MEGA SPRINT & MEGA SPRINT TOWER)
1/2 HP COMMERCIAL DUTY PARKING GATE OPERATOR
INSTALLATION AND SERVICE MANUAL
IMPORTANT: Read and understand Warranty Page first.
Batteries (included) MUST be connected for proper operation of unit. Use...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 2
... Shipped 19 Mega Arm Tower Unique Parts List 19 Mega Arm Options Parts List 19
ACCESSORIES 20
OPERATOR NOTES 21-22
WARRANTY POLICY AND REGISTRATION 23
REPAIR PARTS AND SERVICE 24
2 S2 10 Mode Selections - TABLE OF CONTENTS
INTRODUCTION
Safety Symbol and Signal Word Review 3 Tools Needed For Installation 3 Unit Overview 3
UL325 MODEL CLASSIFICATIONS 4
SAFETY INSTALLATION INFORMATION...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 3
... and control wiring.
• LED diagnostics for right or left handed operation.
• Instant Reverse Device (IRD) monitor senses obstructions during motion.
• Automatic open of gate arm when power is lost if desired (with eight inputs and LED indicators for loops, card reader, radio, etc.
• Reversible arm direction for easy trouble shooting.
Setting the MEGA ARM...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 4
...Installation
Class
Class I & II
Slide Gate Operator
Primary Type
A
Secondary Type
B1, B2 or D
Swing & Gate Barrier (Arm)...control.
4
Type D: Connections provided for a contact sensor. UL325 MODEL CLASSIFICATIONS
CLASS I ) you must provide the following as an airport security area or other building servicing the general public. SAFETY ACCESSORY SELECTION
All UL325 compliant LiftMaster...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 5
... on the bottom edge.
Outdoor or easily accessible controls shall have a security feature to potential hazards.
3.
Improperly designed, installed or maintained systems can create high levels of force in its wiring arranged so the communication between the gate and adjacent structures when opening shall be located where the risk of a swing gate is greater...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 6
... (24" x 24" x 24")
Gate Arm Bracket 7-1/8"
7-1/8"
3-1/2"
42" 10-1/4"
42"
36-1/2"
9-7/8" 8-1/4"
Open Area In Base For Conduit
13-1/2"
14-1/4"
13-1/2"
Side View
12-1/4" Door 14-1/4" Tower Foot Print of the unit. Conduit size should be limited to 1/2" when possible to fit the 3 1/2"x3 1/2" opening in order to be included should be installed with top of curb if...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 7
... lane.
Terminals 9, 10, 11, 12 are the commons (0 Vdc) to be attached to the wires exiting connect the WHITE wire to the
electronic control board. SAMS with a vehicle detector, it was closing motion and not continue to activate the following inputs:
1, 2, 3 OPEN: These inputs will close if closing and a tailgater is restored. The location of the electronic...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 8
... on AC power, install two new, fully charged 12 volt DC batteries on , relay will fire when arm is detected by warranty.
FIGURE 1
Black Lead
-
12 VDC Battery
+
- FIGURE 2
Master J5 1 2 3 4 5 6 7 8 9 10 11 12
MASTER/SECOND WIRING
STEP 1: In a master/second configuration, either unit can be the master and then direct all control wiring to terminal 2 of...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 9
... the control board must be (J4-7) orange then (J4-8) blue (Figure 2). STEP 4: Now check to make sure that the mechanism travels in tight places or when it is set to enable reverse of arm. Now run the gate open /close switch (S3) is desired to have the correct operation, you can install the arm
INSTALLATION NOTE: ARMS LONGER...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 10
...by timer whenever forced up.
MOV
MOTOR
Aux Relay TR
J1 C NC NO DC
1
1
B2 +
PWR
ACC+ ACC-
With all inputs are for the...MEGA ARM the switches 1-5 on S2 are cleared. The default will automatically open time. MODE SELECTIONS - AUTO CLOSE TIMER: Default is reached (activates a swing or slide gate its lane). On will close loop, K1 relay will increase or decrease this hold open...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 11
...board ...Connect terminals 3 and 4 to terminals 1 and 10 on the hand-held remote that will be set at the
AVERTISSEMENT bottom of moving gate or garage door: • ALWAYS keep gate or garage door... Provided)
11 WIRING THE RECEIVER
AVERTISSEMENT...DC ACC+ ACC- DC
1
P1 - FIGURE 2
HIGH SECURITY MODE
OPENING RECEIVER
OPEN RECEIVER
Connect Antenna
Repeat Steps 2 and 3 for
each
remote control...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 12
...opening then the
Install arm in gate arm bracket by sliding the main
If S-2 switch number 8 is off to be sure proper
the cam arm which can be loosened to allow the cam arm magnet
operation will reverse to the magnetic cam arm... power fails), then recheck
AVERTISSEMENT board up holes in arm with AC power off (you apply should be done by a LiftMaster professional.
10. The gate MUST...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 13
... PIN REPLACEMENT
If gate arm is a 2" pin ... Reinstall gate arm bracket
6. Turn on the Control Board Layout page...Liftmaster P/N MBAT batteries. Remove gate arm bracket and pieces in pairs. ADVERTENCIA
ADVERTENCIA
PRECAUCIÓN
ADVERTENCIA
13 Belt loose or needs...oil the new pin then ...is conducted automatically.
Reinstall the arm if required
9. However, to...LiftMaster does not recommend storage ...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 14
...when obstructed. Return of AC power will not operate.
No
Is the AC PWR LED on the Control Board Layout page). No
Restore AC power and/or turn AC
power switch ON.
Does the IRD light..." LED on S2 is 27.5 Vdc with batteries not connected (set with R63, shown on ? Clear the active input to allow the gate to open to function properly. DISCONNECT BATTERIES AND AC POWER BEFORE SERVICING...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 15
If the vehicle pulls up to open or close the gate, use ONLY on a dedicated free exit.
FIGURE 2
Mega Arm Close Loop
Mega Arm
Card Reader Tele-entry Radio Control
DO NOT ALLOW CONTROL DEVICES TO BE WITHIN 10' OF GATE OR OPERATOR
RECOMMENDATION 1: If vehicle detectors are used , use of the above configurations to provide the ability for traffic...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 16
... ON ON
OFF
12345678
Close Loop Trap
S2
Card Reader Tele-entry Radio Control
Mega Arm Trap
Mega Arm
ON
ON ON
ON ON ON
ON
OFF
OFF
12345678
16 Press the relay into the K1 location ensuring the pins are properly aligned.
2. WIRE THE CONNECTIONS BETWEEN THE OPERATORS 1. term#12). 3. Connect the Normally open output (NO) of the K1...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 17
... #8
Other Operator (Slide, Swing, Teeth, etc.)
Open Input
C Extra Open Limit Switch
NC
WIRING: Run 2 wires from the MEGA ARM's K1 relay (common &
S1, #6 and #8 (ON) = K1 Relay PULSE only. gate operator (or MTC-31). Next, run to the other operator to control it to raise again if it will open device (24 hour timer, toggle switch)
can...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 18
... processor and program are running properly. Reader, Push Button Aux Open / Reset (Pulse Open/Close) Safety Loop Input Close Gate Input - Close Loop Back Away - MOV
MOTOR
Aux Relay TR
J1 C NC NO DC
1
1
B2 +
PWR
K1 Relay Terminals (Optional)
ACC+ ACC- CONTROL BOARD LAYOUT
Open Limit Sensor Open Drivers On
Motor Brake On Close Drivers On Close Limit...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 19
... Suppressor Collar Nylon Washer
PARTS SHIPPED
ITEM MEGA ARM Operator Controller Unit Cover Installation and Service Manual Arm Bolts with Washers Nylon Nuts 7AH Batteries
MEGA ARM TOWER UNIQUE PARTS LIST
QTY
ITEM PART NUMBER DESCRIPTION
1
*
MA020T
Unit Cover for Mega Arm Tower
1
*
MA020D
Unit Door for Mega Arm Tower
1
1
MEGA ARM OPTIONS PARTS LIST
2
ITEM PART NUMBER DESCRIPTION...
MATDCBB Green Control Board V.6.4 or newer Manual - Page 20
... MA031).
Hardware Kit: (Only for MA034). of 50).
CPT43 A24
PassportTM 4-Button Remote Control: Includes visor clip.
24Vdc Loop Detector
MA028
MA029 MA030 MA117
Round Padded Arm: 14' x 4" diameter, yellow (requires MA031). Counter Weight: Required for all 15' arms.
MA115
A57 MA201
UN201
MA005C MA200
Wiring Harness: For the A24. MA031 MA025
Adapter Collars: For padded...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 7 months ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Remote Control For Liftmaster /chamberlain 3850 Garage Door Opener
what is the correct remote control for the chamberlain/liftmaster 3850 garage door opener
what is the correct remote control for the chamberlain/liftmaster 3850 garage door opener
(Posted by sendtoalice 9 years ago)
Exit Gate Arm On Mega Arm System Stays Up. The Back Light Is On & Will Not Clea
The exit arm would only operate part of the time and could be made to go down by simply pushing on t...
The exit arm would only operate part of the time and could be made to go down by simply pushing on t...
(Posted by batch40 10 years ago)
Question About Mega Arm/mega Tower 'arm Motion.'
What exactly is the "sensor/trigger" for the Mega Arm/ Mega Tower Arm to rise and fall? Can the uni...
What exactly is the "sensor/trigger" for the Mega Arm/ Mega Tower Arm to rise and fall? Can the uni...
(Posted by avrilshelton 11 years ago)