LiftMaster 3585 Support Question
LiftMaster 3585 Support Question
Find answers below for this question about LiftMaster 3585.Need a LiftMaster 3585 manual? We have 1 online manual for this item!
Question posted by mtjunk on February 9th, 2013
Installing Liftmaster In Place Of Genie
I've had a Genie Intellicode screw drive opener that is very loud. I recently bought a used Liftmaster 3585P (for the quiet belt drive).
Can I use my existing wall control panel and photo-eyes, or do I need to rip them out and purchase Liftmaster wall unit and photo eyes?
(I've tried plugging the wires from the old Genie auxilliaries into the Liftmaster, and I can't get the photo eyes to work. The Genie wall control will initiate the "open" sequence on the Liftmaster, but the independent light on/off button does not seem to work. While the wall switch will "open" the door, it will not "close the door, since the photo eyes do not seem to be working.)
I'd appreciate any advice you can provide.
Thanks,
MT
Current Answers
Answer #1: Posted by GarageDoorMafiadotcom on February 11th, 2013 12:48 AM
GarageDoorMafiadotcom
Member since:
November 4th, 2012 Points: 25,600
Member since:
November 4th, 2012 Points: 25,600
You need LiftMaster or Chamberlain or Craftsman safety sensor and if you like to use the lock and light feature on the wall control that has to be replaced too. It's 2 major brands and they are not compatible with each-other
GarageDoorMafia.com One stop online shop for all your garage door and opener needs.
Related LiftMaster 3585 Manual Pages
3585 Elite Series Manual - Page 1
®
GARAGE DOOR OPENER Model 3585 3/4 HP
For Residential Use Only
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196
www.liftmaster.com
Owner's Manual
■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System® is ...
3585 Elite Series Manual - Page 2
...
Rail assembly parts 35
Installation parts 35
Motor unit assembly parts 36
Accessories
37
Notes
38-39
Repair Parts and Service
40
Warranty
40
INTRODUCTION
Safety Symbol and Signal Word Review
This garage door opener has been designed and tested to your garage door opener 26
Using the wall-mounted door control 27
Using the remote control 28
To open the door manually 29
Care...
3585 Elite Series Manual - Page 3
... prevent damage to garage door and opener:
• ALWAYS disable locks BEFORE installing and operating the opener.
• ONLY operate garage door opener at 120V, 60 Hz to avoid entanglement. Sectional Door
One-Piece Door
Tools needed
During assembly, installation and adjustment of balance. Raise and lower the door to see if there is any ropes connected to garage door. • Complete the...
3585 Elite Series Manual - Page 5
... the motor unit and all parts illustrated below .
Hardware for installation is also listed below . Carton Inventory
Your garage door opener is packaged in the foam. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. LOCK
LIGHT
SmLCarDt CMoontitoronl DPeatneecltTMing Door Control Console
SECURITY✚® 3-Button Remote...
3585 Elite Series Manual - Page 6
... the Rail to the Motor Unit
To avoid installation difficulties, do not run the garage door opener until instructed to do so.
• Remove the bolt and lock nut from rSapirlin,gbTeroltlleaynNdut sAtsysermofbolyam.
3/5/92 - 5/16 /92 - 5/21/92 - 6/2/92
• REMOVE STY6R/1O1/9F2OAM.
• Position belt over the motor unit sprocket. The Chamberlain Group...
3585 Elite Series Manual - Page 7
... INJURY to the installation section. installing or servicing opener. Install garage door opener only on contact with 8x3/8" hex screws provided. ALL repairs to garage door control.
11. Mount emergency release handle 6 feet (1.83 m) above floor.
6. Place entrapment warning label on wall next to cables, spring assemblies and other
(1.5 m). NEVER connect garage door opener to power source...
3585 Elite Series Manual - Page 11
You will need help
at this point. Rail
Door
2x4 is completed. To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of Door
2x4 is not tall enough. • Open the door all the way and place a 2x4 on the top section of the door beneath the rail.
• The top of the door should be level...
3585 Elite Series Manual - Page 12
.... Measure the distance from a falling garage door opener, fasten it SECURELY to structural supports of the hanging bracket to the structural support.
2. Attach one end of the motor unit to required lengths.
3. NOTE: DO NOT connect power to structural supports before installing the opener. Hanging brackets should be used if installing any brackets into masonry. Grease the...
3585 Elite Series Manual - Page 13
... several places. Use insulated staples to secure wire in place.
3. (For standard installations ONLY) Run bell wire up wall and across ceiling to avoid cracking plastic housing. DO NOT pierce wire with care to motor unit.
NOTE: The functional temperature range of the door control is not connected BEFORE installing door
control. • Connect ONLY to each garage door opener. SPECIAL...
3585 Elite Series Manual - Page 14
... Bulb
100 Watt (Max) Standard Light Bulb
Lens Hinge
INSTALLATION STEP 8
Attach the Emergency Release Rope and Handle
• Thread one end of the rope through the hole in an open door falling rapidly and/or unexpectedly. • NEVER use emergency release handle unless garage doorway is clear of lens. Ensure that the rope and...
3585 Elite Series Manual - Page 15
...grounded. The opener must be in the top of electric shock, your garage door opener has a grounding type plug with all local electrical and building codes.
• NEVER use an extension ... screw.
and the ground wire to the screw on the silver terminal; Be sure the opener is required by your local code, refer to establish permanent wiring connection.
• Garage door installation ...
3585 Elite Series Manual - Page 16
... electronic beam. The sending eye (with an amber indicator light) transmits an invisible light beam to the garage door opener BEFORE installing the safety reversing sensor. The units must be securely fastened to avoid drilling extra holes in the path of sectional garage doors without additional hardware. The mounting brackets are available if needed. To prevent SERIOUS INJURY...
3585 Elite Series Manual - Page 25
...
25
Safety Reversing Sensor
ADJUST • If the door stops on striking the obstruction. The garage door opener will flash.
ADJUSTMENT STEP 3
Test the Safety Reversal System
TEST • With the door fully open the door.
• Place the opener carton in the path of the door.
• Press the remote control push button to the fact that the sensor is...
3585 Elite Series Manual - Page 26
... technician.
14. To restore this feature may also need adjustment.
10. ONLY activate garage door when it can close the door with each use emergency release handle to pull garage door open garage door. After ANY adjustments are no effect in the Programming section. ALL repairs to cables, spring assemblies and other control may be turned off as follows: With the...
3585 Elite Series Manual - Page 30
....
• If the trolley does not move in particular can affect door travel.
• Manually check door for flashes on the motor unit then refer to Operation section; The need for occasional adjustment for Using the Wall Mounted Door Control.
• Reprogram remotes following page.
My door reverses for the force and limit settings is normal. This relieves...
3585 Elite Series Manual - Page 31
... LED or Diagnostic
LED
Diagnostic Chart
Installed Safety Reversing
Sensor
Your garage door opener is programmed with jumper wire.
If sending eye indicator light glows steadily, attach the receiving eye. • Align sensors, if the indicator lights glow replace the wires for a short (staple in wire), replace as needed . • Disconnect wires at door control, touch wires together.
3585 Elite Series Manual - Page 33
... operate with your hand-held Remote Control
USING THE "LEARN" BUTTON
USING THE SMART CONTROL PANELTM
LOCK
LIGHT
1. Press the button on the hand-held remote that you press the large push button. All previous codes are not installed, two clicks will be programmed to operate other Security✚® garage door openers.
33 Additional buttons on any...
3585 Elite Series Manual - Page 34
... number (PIN) of your garage door opener. Release the button.
3. The opener light will be changed by ...installed, two clicks will blink four times
when one button close the door even after it has learned the code.
One Button Close: Opener can be closed by pressing only the ENTER button if the one person without using a ladder. 1. To change an existing, known PIN If the existing...
3585 Elite Series Manual - Page 37
Monitors up to three controls into one wall control panel for a garage with NO access door.
OPEN
916LM
Garage Door Monitor Sensor:
Additional accessory sensor for homes with Security✚®: Enables homeowner to three garage doors. Also can be limited to protect LiftMaster® garage door openers against damage from outside by entering a password on a specially designed ...
3585 Elite Series Manual - Page 40
...NUMBER:
1-800-528-9131
LIFTMASTER® GARAGE DOOR OPENER FIVE-YEAR LIMITED WARRANTY
LIFETIME MOTOR AND BELT LIMITED WARRANTY
The Chamberlain ...BELT, WHICH ARE LIMITED IN DURATION TO THE LIFETIME LIMITED WARRANTY PERIOD FOR THE MOTOR AND BELT], AND NO IMPLIED WARRANTIES WILL EXIST...INSTALLED FOR NON-RESIDENTIAL USE. Technical Support Group 6050 S.
Failure to be billed accordingly.
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 7 months ago)
How To Unplug Motor Unit To Install N For Garage Door Opener Elite Series Model
3850
3850
(Posted by Gaydaves 9 years ago)
Liftmaster Elite Garage Door Opener Manual
i have a 3585s opener. always workusing inside control. it has been failing to open at times useing ...
i have a 3585s opener. always workusing inside control. it has been failing to open at times useing ...
(Posted by lgwinnjr 10 years ago)
Programming My Car To Garage Door Opener
I am unable to program garage door to 2012 Acura, is my system to old.
I am unable to program garage door to 2012 Acura, is my system to old.
(Posted by Vherd84 11 years ago)