LiftMaster 1345 Support Question
LiftMaster 1345 Support Question
Find answers below for this question about LiftMaster 1345.Need a LiftMaster 1345 manual? We have 1 online manual for this item!
Question posted by alisonwood on August 6th, 2012
Liftmaster Cptk-3, How Do I Program My New Key Remote To Existing Garage Door
The person who posted this question about this LiftMaster product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related LiftMaster 1345 Manual Pages
1355 Manual - Page 1
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com
®
GARAGE DOOR OPENER Model Series 1300
For Residential Use Only
Model 1356 - 1/2HP Model 1346 - 1/3HP
Model 1355 - 1/2HP Model 1345 - 1/3HP
Owner's Manual
■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the...
1355 Manual - Page 2
... in this Signal Word on the following pages, it will alert you to
WARNING your garage door opener 33
Having a problem 34
Programming
35-36
To add or reprogram a hand-held remote control .....35
To erase all codes 35
3-Button remotes 35
To add, reprogram or change a Keyless Entry PIN 36
Repair Parts
37-38
Rail...
1355 Manual - Page 3
... see if there is not sticking or binding: 1.
CAUTION
To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and operating
the opener. • ONLY operate garage door opener at 120V, 60 Hz to avoid entanglement. Sectional Door
One-Piece Door
Tools needed
During assembly, installation and adjustment of which are under EXTREME tension. •...
1355 Manual - Page 4
... will require hardware not provided.
• Do you proceed with glass panels, etc.). Floor or door should be repaired.
is normal when
garage door is required (Installation Step 11).
• The opener should be installed above the garage door. Look at the garage door where it helpful to refer back to install sensors.
• Installation Step 10 -
Depending...
1355 Manual - Page 5
....
• The floor or the garage door MUST be
SERIOUSLY INJURED or KILLED by a closing garage door.
• The gap between floor and bottom of door must
not exceed 1/4" (6 mm)
Header Bracket
Rail Door Bracket
Header Wall
Garage Door
Straight Door Arm
Curved Door Arm
Emergency Release Rope & Handle
ONE-PIECE DOOR WITH TRACK
Access Door
Safety Reversing Sensor
Gap between the...
1355 Manual - Page 6
... garage door opener is packaged in
the foam.
Hardware for assembly and installation is shown on the model purchased. Save the carton and packing material until installation and adjustment is missing, carefully check the packing material. If anything is complete. Model 1355 & 1345 ONLY
Lighted Door Control Button w/6ABx1-1/2" screws
SECURITY✚® Single-Button Remote...
1355 Manual - Page 8
...and insert the front tab in the slot on the trolley to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener. Cut tape
from motor unit!
• Tighten both screws ...Front Tab Slot
Mounting Plate
8 ASSEMBLY STEP 1
Fasten the Rail to the Motor Unit
MODELS 1355 AND 1345 ONLY (For Models 1356 and 1346 see page 9)
• Remove the two washered bolts mounted in ...
1355 Manual - Page 9
ASSEMBLY STEP 3
Fasten the Rail to door opener. Styrofoam Packaging
Chain Rail
Washered Bolts 5/16"-18x1/2"
USE ONLY THIS TYPE AND...; Fasten the rail with the two washered bolts previously removed. Tighten securely. WARNING
CAUTION
To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in top of any other bolts will cause serious damage to the Motor Unit...
1355 Manual - Page 10
... AND 1346 ONLY
• Line up the holes in the chain spreader with the hardware provided.
• Remove the trolley threaded shaft from
CAUTION moving garage door opener:
• ALWAYS keep hand clear of sprocket while operating...
1355 Manual - Page 18
... terminal screws and the antenna are no obstructions to door travel to the full open circuit.
4. NEVER permit anyone to cross path of the opener. Fasten the Lighted Door Control Button securely with a staple, creating a short or open position but will travel . • ALWAYS keep garage door in sight until the sensor beam is not connected BEFORE...
1355 Manual - Page 30
... inch, and the opener lights will not close from a remote if the indicator light in either sensor is misaligned or obstructed). If the opener closes the door when the safety reversing sensor is obstructed (and the sensors are made, the safety reversal
system MUST be
SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal...
1355 Manual - Page 31
... MUST be programmed before use handle to move . • The wall-mounted Door Control: Hold the push
button or bar down travel .
4. If you purchase a new remote, or if you can be seen clearly, it must be tested every month. Garage door MUST reverse on when someone walks through the open , the door will reverse.
ALWAYS keep garage door in...
1355 Manual - Page 33
... Repeat with a piece of wire. If it is off.
• Program the opener to match the remote control code. (Refer to the following two conditions: (1) this device may...opener to a metal door, foil backed insulation, or metal garage siding.
5. The opener does not require additional lubrication.
Short the red and white terminals by a wall switch.)
• Have you disabled all remotes...
1355 Manual - Page 34
... don't blink:
• Is something obstructing the door? Having a Problem? (Continued)
6. The garage door opens and closes by its springs. The door doesn't open all the way, increase the up force. For an existing installation, see below.
Close the door and use on page 29.
• If door reverses in case of door arm length, close completely:
• Review the...
1355 Manual - Page 35
... THE "LEARN" BUTTON
1
2
3
9
1
7
3
5
KG
9
1
7
3
5
KG
1
2
To Erase All Codes From Motor Unit Memory
1
2
To deactivate any Security✚® 3-button remote or mini-remote can be heard.
35 Your garage door opener has already been programmed at the factory to operate it. Release the button when the motor unit lights blink. All previous
codes are not...
1355 Manual - Page 36
...set a temporary PIN:
1. After a programmed number of hours or number of accesses,...existing, known PIN
1
2
3
9
1
7
3
5
KG
9
1
7
3
5
KG
If the existing PIN is deactivated.
36 To Add, Reprogram or Change a Keyless Entry PIN
NOTE: Your new Keyless Entry must be heard. Press the four buttons for the present PIN, then press and hold buttons 1 and 9 for your garage door opener...
1355 Manual - Page 37
...button remote control
3
10A20
3V2032 Lithium battery
4
29B137
Transmitter visor clip
5
41A2828 Emergency release rope & handle
assembly
6
41B4494-1 2-conductor bell wire - white &
white/red
7
41A4353 Header bracket w/clevis pin & fastener
8
41A5047 Door bracket ... Parts
1 5
NOTICE
12
3 6
2
7
CEILING MOUNT ONLY UP
8 10
9 11
4 KEY PART
NO. REPAIR PARTS
Rail Assembly Parts...
1355 Manual - Page 38
...Opener assy. DESCRIPTION
11 41D3058
Universal replacement motor & bracket assy.
NO. Complete with : Motor, worm, bracket, bearing assembly, RPM sensor.
12 41A3583-11 41A3583-15
13 41A2818
Cover 1/2HP (1356, 1355) Cover 1/3HP (1346, 1345... - 1/3HP 9 12A373 Capacitor bracket 10 41A3150 Terminal block w/screws
KEY PART NO. hardware kit (includes screws not designated by a number in...
1355 Manual - Page 39
...and a Light Feature for constant light.
98LM
902LM/903LM
2 & 3 Door Multi-Function Wall Control:
Ideal for homes with an additional LiftMaster Security✚® remote. Monitors up to turn opener lights on or off from the control panel.
915LM
Garage Door Monitor:
Security for the largest door of garage door opener from outside by disengaging trolley.
8 Foot (2.4 m) Complete Rail: To...
1355 Manual - Page 40
..., THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES.
IN NO EVENT SHALL SELLER'S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. SIMPLY DIAL OUR
TOLL FREE NUMBER:
1-800-528-2817
www.liftmaster.com...
Similar Questions
How To Program New Car To Open Garage Door
where is the learn button to program my car to open garage door
where is the learn button to program my car to open garage door
(Posted by lrothberg 6 years ago)
All Remote Controls Of My Lm 1345 Stop Working Suddenly. Door Control Still Ok.
All remote controls of my LM 1345 stop working all the sudden. When I press the transmit button on a...
All remote controls of my LM 1345 stop working all the sudden. When I press the transmit button on a...
(Posted by huangtingwei 9 years ago)
My Opener Works Fine From The Wall Unit. None Of The Remotes Work.
The wall unit works fine but the remotes just stopped working. I reset the codes and can not reset t...
The wall unit works fine but the remotes just stopped working. I reset the codes and can not reset t...
(Posted by Nelsoneric84 11 years ago)
How To Change Bakup Battery
It keeps beeping and I think it is time to change battery. I can not find the procedure in manual.
It keeps beeping and I think it is time to change battery. I can not find the procedure in manual.
(Posted by mhkabir01 11 years ago)
Resetting The Key Code For Garage Door Opener
How do you reset the key code for the garage door opener?
How do you reset the key code for the garage door opener?
(Posted by khiggins69 12 years ago)