Lexmark T650 Support Question
Lexmark T650 Support Question
Find answers below for this question about Lexmark T650.Need a Lexmark T650 manual? We have 9 online manuals for this item!
Question posted by Leanneden on December 20th, 2013
How To Clear Language On A T650 Lexmark Printer
The person who posted this question about this Lexmark product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Lexmark T650 Manual Pages
User's Guide - Page 130
.... When attempting to
print data in permanent storage. Notes:
• Off is the factory default setting. • This menu appears only if a non-Read Only printer hard disk
is the factory default printer language. • Setting a printer language as the default does not prevent a
software program from the print queue if they require unavailable...
User's Guide - Page 131
... set to 100%.
• Changing this setting from the Print dialog and pop-up menus. Off sets the printer to process print jobs.
• The On setting retains the downloads during language
changes and printer resets. It should not be Read/Write or Write protected.
Menu item Job Accounting
On Off
Resource Save...
User's Guide - Page 151
....
Note: The current interface displays on the flash drive, or the files saved are disabled, it is active.
Understanding printer messages
151 Menus are Disabled
The printer menus are offline. Wait for the printer to clear.
If x equals 0, then the standard network interface is still possible to cancel a print job, print a confidential job, or...
User's Guide - Page 152
...
Wait for the message to clear. Warning-Potential Damage: Do not turn the printer power off while Programming flash appears on the display. It appears after the Ready or Power Saver message. Power Saver
The printer is saving power while it is displayed.
Parallel/Parallel
The printer is the Printer Job Language (PJL) Ready message. Programming...
User's Guide - Page 156
..., this message is denied until Continue appears, and then press • Cancel the current print job. Order a maintenance kit, which contains all blocks are cleared.
The printer may continue to enter menus is displayed. Note: There is a defined limit on what type of media is dependent on the number of the following...
User's Guide - Page 161
... the following:
• Press the arrow buttons until Continue appears, and then press • Turn the printer off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. to clear the message.
56 Serial port disabled
is the number of the following :
1 Turn the...
User's Guide - Page 198
...in conformance with ISO 7779 and reported in countries of the printer. We encourage the recycling of our products. See www.lexmark.com for T654
Scanning
N/A
Copying
N/A
Ready
30 dBA
...further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your product.
1-meter average sound pressure, dBA
Printing
53 dBA for T650, 54 dBA for T652, 55 dBA...
User's Guide - Page 215
...153 Reattach envelope feeder 154 recycled paper
using 67 recycling
Lexmark products 170 WEEE statement 198 Remote Management Active 154 Remove...printer
problems 175 troubleshooting, display
display is blank 175 display shows only
diamonds 175 troubleshooting, paper feed
message remains after jam is cleared... 176 Large jobs do not collate 178 multiple-language PDFs do not print 176 paper curl 186 paper...
Service Manual - Page 1
Edition: September 17, 2009
Lexmark™ T650, T650n, T652dn, T654dn & T656dne Printer 4062-XXX
• Table of contents • Start diagnostics • Safety and notices • Trademarks • Index
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
Service Manual - Page 5
...Test 3-18 Feed Tests (finisher 3-18 Sensor Test (finisher 3-18
BASE SENSOR TEST 3-19 PRINTER SETUP 3-19
Defaults 3-19 Printed Page Count 3-19 Perm Page Count (permanent page count 3-... Print Log 3-23 Clear Log 3-24 EXIT DIAGNOSTICS (models T650, T652, and T654 3-24 Configuration menu (CONFIG MENU) (models T650, T652, and T654 3-25 Entering Configuration Menu (models T650, T652, and T654...
Service Manual - Page 6
...Clear Custom Status 3-28 Best Speed 3-29 Exit Config Menu (models T650, T652, and T654 3-29 Understanding the printer control panel (model T656 3-29 Accessing service menus (model T656 3-30 Diagnostics Menu (model T656 3-31 Entering Diagnostics Menu (model T656 3-31 Available tests 3-31 Registration (printer... Test 3-43 Disk Test/Clean 3-43 PRINTER SETUP 3-44 Defaults 3-44 Printed Page ...
Service Manual - Page 7
...Repeat Rate 3-58 Wiper Message 3-58 Clear Custom Status 3-58 USB speed 3-59 Exit Configuration Menu (model T656 3-59 Printer overview 3-60 Basic model 3-60 Printer theory 3-61 Model T650 with duplex, paper path, rolls,..., types, and weights 3-66 Paper sizes supported by the printer 3-66 Registration 3-67 Sensor (input 3-67 Aligner assembly 3-67 Transfer 3-68 Transfer roll assembly 3-68
...
Service Manual - Page 29
General information 1-5
More information is available at our Lexmark Web site at www.lexmark.com/ multifunction printers.
or 550-sheets
8
Optional 2000-sheet tray (Tray...stability. CAUTION: Floor-mounted configurations require furniture for the T650 model. Not applicable
2 Up to two 5-bin mailbox units are supported.
3 The printer supports up to three output expander units, or one ...
Service Manual - Page 37
...take the printer 10-20 seconds to determine if the print cartridge is defective. wait a few seconds, and then turn the power back on page 4-74. 4. Diagnostic information 2-3 Message is cleared when a...used . Possible repair actions
Turn the power off; The printer determines the paper length is too short to "Switch (media size) assembly removal (T650, T652, T654)" on . Replace the media tray ...
Service Manual - Page 42
..." on , or during flash format and write operations.
1. This error may be replaced with the customer's datastream, and not the RFID Option itself. To clear this IR, the printer cartridge must be taken:
• Press
to clear the
message and continue
processing the job.
• Press until the
problem is resolved.
2-8 Service Manual
Service Manual - Page 44
... RFID option for the first time, reporting of further errors is suppressed until the menus are entered or the printer is reset. Reset Printer
Reset Active Bin
The following actions may be taken:
• Press
to clear the
message. Reset Printer
Reset Active Bin
1. Either no input trays or there are entered, or the...
Service Manual - Page 211
... properly configured. For more network troubleshooting information, consult the Lexmark Network Setup Guide.
Problem resolved
3 Check the printer's online status under Menu Reports - Did this service check...If a wireless network is used, verify that the device is found under Printers Go to "System card assembly removal (T650, T652, T654, T656)" on the host computer. Is the cable properly...
Service Manual - Page 217
... properly aligned on page 3-24
Exiting Diagnostics mode (models T650, T652, and T654)
Select Exit Diagnostics to the margins...Log" on page 3-23 See "Print Log" on page 3-23 See "Clear Log" on the page. Press until the appears next to Ready mode.
... setting you need to reset the value. Resetting the Printer displays, the printer performs a POR, and returns to Quick Test.
Press ....
Service Manual - Page 236
... some cases
The printed event log can be faxed to EVENT LOG.
Clear Log
Use Clear Log to EVENT LOG. Select Clear Log from EVENT LOG. This affects both the viewed log and the ...models T650, T652, and T654)
This selection exits Diagnostics mode, and Resetting the Printer displays. To print the event log:
Select Print Log from the Event Log menu.
2.
Press Back
to return to Lexmark or...
Service Manual - Page 237
..." on page 3-28 See "Clear Custom Status" on page 3-28...for Prompts Font Sharpening Wiper Messages Clear Custom Status Best Speed Exit Config ... printer usage. Diagnostic aids 3-25 Turn on the top line of the printer....The message CONFIG MENU displays on the printer. 4.
A print job containing a single...reminded that the printer requires scheduled maintenance. Turn off the printer. 2. Maintenance ...
Similar Questions
How To Change The Ip Address On A Lexmark T650 Printer
(Posted by thacaalka 10 years ago)
T650 Printer Giving A 935.24 Print Head Error
WHILE PRINTING MY T650 PRINTER QUIT AND GAVE A 935.24 PRINT HEAD ERROR MESSAGE
WHILE PRINTING MY T650 PRINTER QUIT AND GAVE A 935.24 PRINT HEAD ERROR MESSAGE
(Posted by Anonymous-67066 11 years ago)