Lexmark 260d Support Question
Lexmark 260d Support Question
Find answers below for this question about Lexmark 260d - E B/W Laser Printer.Need a Lexmark 260d manual? We have 2 online manuals for this item!
Question posted by ebgc on April 19th, 2011
On My Lexmark 260d, The Load Paper Light Will Not Turn Off And I Can't Print?
The load paper light will not turn off on our Lexmark 260d after we load paper and shut the drawer. We can't print. Any suggestions?
Current Answers
Answer #1: Posted by LexmarkListens on July 7th, 2011 9:25 AM
LexmarkListens
Member since:
July 1st, 2011 Points: 1,410,540
Member since:
July 1st, 2011 Points: 1,410,540
Tray 1 is the default factory settings for the printers paper source, check the print settings of your word processor. Make sure that the paper source is set to Tray 1.
To do this, please follow the steps below.
- With a document open, click File > Print.
- Click Properties > Paper tab.
- Set the correct input options like the correct paper size, paper tray and paper type and click OK.
- Click OK
For further assistance, please call Lexmark Technical Support.
Lexmark Listens
Phone:
USA: 1-800-539-6275
Canada: (877) 856-5540
UK: 0800 121 4726
South Africa: 0800 981 435
Related Lexmark 260d Manual Pages
Quick Reference - Page 1
... tabs, and then slide them to the printer at one optional drawer (which includes an optional tray) may cause a jam. Only one time. Proper paper loading prevents jams and facilitates trouble-free printing. 1 Pull the tray completely out. Busy - The factory default paper type setting is plain paper, so the paper type setting must be attached to the...
Quick Reference - Page 2
... not load A6-size paper to lightly touch the side of the stack.
Note: Notice the maximum fill line. Do not try to the A6 size position. If you are loading A6-size paper: a Squeeze the length guide tabs together as shown with the design placed facedown. Loading paper and specialty media
2
Load the letterhead with the recommended print...
Quick Reference - Page 3
... use
2 When the light is located inside the manual feeder door of the printer and can feed only one sheet of the tray. Loading paper and specialty media
3 Warning-Potential Damage: Do not force the paper into the center of paper was loaded than the type previously loaded in neater stacking of 20 lb paper.
The paper stop
The standard...
Quick Reference - Page 4
... so it flips forward. Load up to the point where its
1 sheet of paper
Note: Only one optional drawer may cause creases in the transparencies.
• When moving the printer to
Tray 1 250 sheets of paper 150 sheets of the trays and the manual feeder are printing on the printer at a time. Paper capacities
The capacities of A6...
Quick Reference - Page 5
... guides in an appropriate environment. • Do not remove trays while the printer is printing. Inside
this door is printing.
Note: The jam messages listed appear on before loading it.
• Do not use paper that the tray may be removed:
Load paper - On - The light sequence for how to access jam areas. On - Make sure the stack...
Quick Reference - Page 6
... one of the following : • Open the front door, and then open the rear door. • Remove Tray 1, and then depress the lever.
202.yy Paper jam - Blinking - Blinking
- On
- On - On - Try one of the following :
• Remove Tray 1, and then depress the lever. • Open the front door, and...
Quick Reference - Page 7
...: Do not touch the photoconductor on a flat, clean surface.
Try one of the printer might be hot. On - Clearing jams from the standard exit bin
A duplex print job was sent to cool before touching.
3 Remove the jammed paper.
251.yy Paper jam - A sheet is not easy to remove, then open the rear door to...
Quick Reference - Page 8
... the standard exit bin.
2 Remove the jammed paper.
4 Insert the tray.
Clearing jams in or behind Tray 1, the standard tray:
1 Remove Tray 1.
3 If necessary, depress the lever to free the paper and remove the jam.
5 Press to continue printing. Clearing jams from Tray 1
To see whether paper is jammed in the manual feeder
Clearing...
Quick Reference - Page 9
...risk of the printer might be grasped and pulled straight out. The paper may be removed this way, check for jammed paper behind the photoconductor kit and toner cartridge unit.
Paper jammed in the... page 7.
For more information, see "Clearing jams behind the rear door
If the paper is not exiting the printer:
1 Push the release button, and then lower the front door
CAUTION-HOT SURFACE:...
Setup Sheet - Page 1
All rights reserved.
*34S0254*
Rev 001
4/08 P/N 34S0254
© 2008 Lexmark International, Inc.
Similar Questions
Load Paper Light
although the tray is full of paper, when trying to print the printer will appear to run through its ...
although the tray is full of paper, when trying to print the printer will appear to run through its ...
(Posted by waynegale 8 years ago)
Add Paper Light On And No Print
Tray full of paper, change paper light stays on and won't print
Tray full of paper, change paper light stays on and won't print
(Posted by jsedor 11 years ago)
260d First Two Lights Are Flashing
My 260d just started having a problem - the first two lights on the left started flashing. I reboot ...
My 260d just started having a problem - the first two lights on the left started flashing. I reboot ...
(Posted by hwrhoades 12 years ago)
Light Ink On Paper
It is a brand printer. It has paper,ink(have tried multiple cartiges from other machines)and feeds p...
It is a brand printer. It has paper,ink(have tried multiple cartiges from other machines)and feeds p...
(Posted by jessethompson 12 years ago)
The Exclamation Light Is On And I Cannot Print Anything
(Posted by sscriver 13 years ago)