Lantronix MSS4 Support Question
Lantronix MSS4 Support Question
Find answers below for this question about Lantronix MSS4.Need a Lantronix MSS4 manual? We have 4 online manuals for this item!
Question posted by avelasquez63014 on January 4th, 2016
Default Factory
como resetear a valores default factory un MSS4
Current Answers
Answer #1: Posted by TechSupport101 on January 4th, 2016 9:07 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. There is a reset button at the back of the unit. When this reset button is pressed and held during the power up and boot procedure for at least 3 seconds, the MSS-VIA returns to its factory default configuration
Related Lantronix MSS4 Manual Pages
MSS User Guide - Page 12
... and a power connector.
2-1 Read this chapter completely before continuing. Basic knowledge of the MSS-VIA, MSS4, and MSS100 in a network. Figure 2-1: MSS-VIA Front Panel
Note: When the reset button is assumed... power up and boot procedure for at least 3 seconds, the MSS-VIA returns to its factory default configuration. MSS-VIA Installation
Components
The MSS-VIA front panel has a male DB9 RS-232 ...
MSS User Guide - Page 27
...Properties subpage or the TCP/IP subpage. Figure 3-2: Changing Privileged Password for MSS-VIA and MSS4
Local> SET PRIVILEGED Password> system (not echoed) Local>> CHANGE SERVER PRIVPASS "walrus"
Figure.... Using a Web Browser
The Web Manager web browser interface can be changed from the default natural subnet configuration (e.g., 255.255.255.0 for this MSS. Using EZWebCon
Use the following...
MSS User Guide - Page 29
... reply to the serial console and press the Return key. BOOTP and RARP are enabled by default on Boot Configuration Program (BCP) commands, see the Local> prompt.
See the host-based ... pages for assistance. Figure 3-8: Entering the IP Address at the Local Prompt for MSS-VIA and MSS4
Local> SET PRIVILEGED Password> system (not echoed) Local>> CHANGE SERVER IPADDRESS 192.168.0.10
Figure ...
MSS User Guide - Page 30
...Local> SET PRIVILEGED Password> system (not echoed) Local>> CHANGE LOGINPASS "badger"
Note: Default passwords may wish to disable incoming logins, the MSS can be changed with the Change Server... Incoming Password command.
Figure 3-10: Changing the Login Password for MSS-VIA and MSS4
Local> SET PRIVILEGED Password> system (not echoed) Local>> CHANGE SERVER LOGINPASS "badger"
Figure...
MSS User Guide - Page 35
MSS User Guide
4: Configuration
Factory Defaults
You should work for most networks. IP Address The IP address can be changed ... Figure 4-3: Setting the Subnet Mask for MSS-VIA and MSS4
Local>> CHANGE SERVER SUBNET MASK 255.255.255.0
Figure 4-4: Setting the Subnet Mask for a given network.
This should only restore factory default settings if you will need to see the hosts on other...
MSS User Guide - Page 36
... The MSS also allows you do not have a domain at the end.
4-3 To set a default domain name to be appended to any host name for the purpose of name resolution. Figure 4-5: ... as Phred, in quotes
Figure 4-9: Configuring the Default Domain for MSS-VIA and MSS4
Local>> CHANGE SERVER DOMAIN "xyzcorp.com"
Figure 4-10: Configuring the Default Domain for more information. MSS User Guide
4: ...
MSS User Guide - Page 38
... download fails, the MSS will advertise itself as a router to use on the MSS.
By default, the MSS is the frame type. MSS User Guide
4: Configuration
The MSS will respond to queries...NetWare loadhost to the network using the Change Server SNMPSetComm command with the MSS-VIA and MSS4 or the Change SNMPSetComm command with read from a host and normal operation commences.
The MSS...
MSS User Guide - Page 41
...MSS, enter the Change RS485 Enabled command. As many as 32 devices can be implemented by default. There are slaves. It only moves data between serial and Ethernet. Any RS-485 protocol ... sent so that the
4-8
Enabling RS-485 Mode for a serial connection on all four ports;
MSS4 allows for MSS4
Local> CHANGE RS485 PORT 2 ENABLED
Figure 4-20. Lantronix recommends the use .
‹ The ...
MSS User Guide - Page 44
... Configuration
The serial ports are desired, Autostart should remain disabled (the default).
4-11 MSS User Guide
Figure 4-31: RS-422 Connection
4:... CD) at RS-232 level, and listens for those signals at the factory for 9600 baud, 8 data bits, one stop bit, and no parity... 4-32: Changing Serial Port Access Mode for MSS-VIA and MSS4
Local>> CHANGE PORT 1 ACCESS LOCAL
Figure 4-33: Changing Serial...
MSS User Guide - Page 45
... trigger that data. For example, when using Modem Emulation Mode you can no default Autostart character; You can also specify whether the trigger characters will happen as soon...to the Local> prompt. Figure 4-40: Transmitting Serial Data with a Character Trigger for MSS-VIA and MSS4
Local>> CHANGE PORT 1 DATASEND CHARACTER Z
Local>> CHANGE PORT 1 DATASEND SAVE 1
Figure 4-41: ...
MSS User Guide - Page 46
... of 8 data bits can be Even, Mark, Odd, or Space. Figure 4-44: Enabling Autobaud for MSS-VIA and MSS4
Local>> CHANGE PORT 1 AUTOBAUD ENABLED
Figure 4-45: Enabling Autobaud for the MSS100) followed by default, but can also be changed to 7 data bits. MSS User Guide
4: Configuration
The examples in Figure 4-40and Figure...
MSS User Guide - Page 47
... commands, is discussed in most situations. Figure 4-50: Enabling Passflow for MSS-VIA and MSS4
Local>> CHANGE PORT 1 PASSFLOW ENABLE
Figure 4-51: Enabling Passflow for MSS100
Local>> CHANGE FLOW...at all, specify None. XON/XOFF controls data flow by default.
Figure 4-48: Enabling Recommended Flow Control for MSS-VIA and MSS4
Local>> CHANGE PORT 1 FLOW CONTROL CTSRTS
Figure 4-49: ...
MSS User Guide - Page 50
...PC card slot, reboot the MSS.
Figure 4-63: Defining a Preferred Service for MSS-VIA and MSS4
Local>> CHANGE PORT 1 PREFERRED TCP 192.168.0.10
Figure 4-64: Defining a Preferred Service for MSS100... defined using the Change Port Dedicated command. This section assumes that came with its default 802.11 settings, and settings can be available. The MSS attempts to change connection...
MSS User Guide - Page 58
....
Users can configure a local switch key. Figure 5-6: Defining a Local Switch for MSS-VIA and MSS4
Local>> CHANGE PORT 1 LOCAL SWITCH ^L
Figure 5-7: Defining a Local Switch for MSS100
Local>> CHANGE... following section explains commands used to host Duff. Each separate connection is also circular; By default, the MSS handles the Break key locally. The list is a session. He then breaks...
MSS User Guide - Page 60
...although in less detail than in this virtual serial line is only valid on the MSS-VIA and MSS4. The first lines display the MSS version, hardware address, network name and node number, identification string...to the MSS-VIA only.
5-5 Settings such as flow control, baud rate, parity, and default hosts are shown. MSS User Guide
5: Using the MSS
Show IPsecurity
This command shows the current TCP/...
MSS User Guide - Page 61
...and accept packets from the other MSS.
The commands for MSS100 is as follows for MSS-VIA and MSS4:
MSS_A
Local>> CHANGE PORT 1 DEDICATED TCP 192.168.0.10:3001T Local>> CHANGE PORT 1 AUTOSTART ... parameters have been configured properly, the device servers are on different IP subnets, the default gateway on each unit will automatically connect to MSS_B each MSS must be told explicitly which...
MSS User Guide - Page 67
... configured your system's /etc/services file. Refer to the DHCP Manager on the MSS4 and MSS-VIA.
The download file is functioning correctly. Specify the complete pathname for... a TFTP boot, the flash ROM code is automatically disabled.
configuration file, or add a default pathname to the download filename. MSS User Guide
6: Troubleshooting
Problem/Message
Error
Remedy
The MSS ...
MSS User Guide - Page 69
...The device server then reboots using the Flash command and will attempt to load the file MSSVIAx.SYS, MSS4.SYS, or MSS100.SYS from the host at the Boot Prompt
If the Boot> prompt appears on ... a message to the console and wait ten seconds for the Boot> prompt. If the loadfile is enabled by default.
6-4
If the MSS can be entered at the Boot> prompt to configure the MSS. MSS User Guide
6:...
MSS User Guide - Page 73
...MSS4 Connectors
Serial Connectors
The MSS4 has four serial ports. The default serial port settings are 9600 baud, 8 bits, no parity, and 1 stop bit. The MSS4 models have DB9 connectors. RS-485 DB9 Connectors The MSS4...information, see
RS-485 Configuration. The following sections show the pin connections of the MSS4 DB9 connectors, which provide dual RS-232/RS-485 serial ports.
Do not ...
MSS Reference Manual - Page 73
Override Forces the current port to the MSS-VIA and MSS4. See Also
Change 80211, page 2-2;
Restrictions
Secure users may not become the privileged port (the previous port loses
the privilege). Parameters
Privileged Allows a user to its factory defaults.
Noprivileged Removes privileged status for instructions. Also displayed are any parameters displays basic 80211 settings...
Similar Questions
How Do I Reset Without Password?
I have a Lantronix XPort device that has been used in the field, but no one knows the password. Can ...
I have a Lantronix XPort device that has been used in the field, but no one knows the password. Can ...
(Posted by schumar 6 months ago)
What Is The Default Ip Address Of The Eds 1100
what is the default IP address of the EDS 1100
what is the default IP address of the EDS 1100
(Posted by michaelpickle 4 years ago)
Password
what is the default password for this device when is used IE o Chrome ? and also ; how to factory re...
what is the default password for this device when is used IE o Chrome ? and also ; how to factory re...
(Posted by floresfernandoc 6 years ago)
Serial Connection To Eds16ps
I'm unable to connect to the Lantronix EDS16PS using putty's serial session as my computer doesn't s...
I'm unable to connect to the Lantronix EDS16PS using putty's serial session as my computer doesn't s...
(Posted by navedkhwaja 7 years ago)