Kyocera FS C5015N Support Question
Kyocera FS C5015N Support Question
Find answers below for this question about Kyocera FS C5015N - Color LED Printer.Need a Kyocera FS C5015N manual? We have 14 online manuals for this item!
Question posted by jchitty on June 22nd, 2012
What Do I Do If The Paper Feed Unit Is Stuck In A Kyocera Fs-c5015 Printer?
I am trying to remove the paper feed unit in a Kyocera FS-C5015 and it is stuck. I pull the green handle and it releases, but will not slide out of the printer. Feels like it is hanging up or binding up on something.
Current Answers
Related Kyocera FS C5015N Manual Pages
PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 358
... best print quality is achieved with different thicknesses of paper and print density. Function
The TATR command applies a paper source (MP tray or cassette) thickness of paper.
TATR 0, 1, 3; EXIT; This enables the printing system to the FS-1000 printer only. All trays are reset when all paper sources to the defaults: !R! apply Tray ATtributes
Format
TATR...
Kyocera Command Center Operation Guide Rev 6.3 - Page 22
... mode to High or Low. Gloss Mode Sets Gloss Mode to Normal or Fine. Color Mode Sets Color Mode to print. Paper Feed Mode Determines the behavior of paper feed selection when the paper you requested of copies to Black & White (Monochrome) or Full Color. Copies Sets the number of size and/or type is 30 seconds. The...
PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 126
... n Select printwheel type Upper cassette (for sheet 1) Lower cassette (for sheet 2) Manual paper feed (for envelope) Eject page Memory test Request status byte 1 Request status byte 3 Initialize printer Remote error reset Disable NAK error response from printer Reenable NAK error response from printer Set (n-1)/48-inch line spacing Set (n-1)/120-inch character spacing Increase carriage...
PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 216
... number of linefeeds that will occur when the buffered label is not down until the paper feeding completes in plotter units by ASCII-coded integers, as follows:
KC-GL option Plotter model (FRPO G0)
... eight ASCII-coded integers separated by the printing system, as +1.
An inversed line feed (VT) counts as -1, and a linefeed (LF) counts as follows:
Buffer allocation Polygon instruction Arc...
FS-C5015N/C5025N/5030N Operation Guide (Advanced) - Page 13
... the printed page depends on the whiteness of paper fiber.
Handling Paper
grain paper can cause feeding problems in the Output Tray. When paper passes through the fixing unit, it from a reputable supplier is sold specifically for use with copiers or printers (heatfusing type). To produce flat printouts, load the paper so that these problems do not cling together...
FS-C5015N/C5025N/5030N Operation Guide (Advanced) - Page 33
...the printer requires maintenance or is switched on-line by switching the printer off -line. Indicates that a data is off -line.
• Print and feed out one page when the printer displays...[GO]. Indicates that the printer is being received.
Indicates either that data received is ready and on the message display).
NOTE: The printer has a USB, parallel (FS-C5030N), network, and an...
FS-C5015N/C5025N/5030N Operation Guide (Advanced) - Page 86
The MP tray can feed paper from any paper source you desire to feed paper from the paper source originally selected. The printer can be used up (approximately 100 sheets), paper will be kept empty if you command on the printer driver. Using the Operator Panel
Paper Handling
MP Tray Mode
This section explains how to change Cassette to First. 7 Press [OK...
FS-C5015N/C5025N/5030N Operation Guide (Advanced) - Page 92
... types:
Plain Preprinted Bond Recycled Rough Letterhead Color Prepunched High quality Custom 1 (to 8)
7 When the desired cassette type is also available for the optional paper feeders.
5 To change the current paper feed source,
press [OK] ([ENTER]). Paper Handling >
3 Press Z. 4 Press U or V repeatedly until Paper Handling > appears. Cassette 1
6 Press U or V to display the desired...
FS-C5015N/C5025N/5030N Operation Guide (Advanced) - Page 93
... short edge or long edge binding mode. Binding Modes
Binding refers to the bottom paper cassette):
MP tray Cassette 1 Cassette 2 Cassette 3 Cassette 4
Cassettes 2, 3 and 4 are available for the following paper types:
Plain Preprinted Bond Recycled Rough Letterhead Color Prepunched High quality
Activating the duplexer is mounted underneath the printer. Duplex Printing
Using the optional...
FS-C5015N/C5025N/5030N Operation Guide (Advanced) - Page 124
... fonts, etc., to the bottom of the printer for continuous feeding of a large volume of paper. Memory Card Slot
PF-60 Paper Feeder
The PF-60 paper feeder allows you power on page 2-51. To manually read from the control panel or automatically when you to add 3 (1: FS-C5015N) more paper cassettes to a flash memory card. NOTE: Before...
FS-C5015N/C5025N/5030N Operation Guide (Advanced) - Page 144
... how to select 2-44
Outline font Glossary-2 Output device
how to select 2-72 Override A4/Letter
description 2-69
P
Page protect mode how to select 2-45
Paper minimum and maximum sizes 1-3 paper sizes tabled, as Paper Size indicator 2-5 paper types, as Paper Type indicator 2-6 recommended makes and types 1-3
Paper cassette selecting the paper feed source 2-66
Index-2
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 32
You can perform on the printer. Maintenance
General Information
This chapter describes basic maintenance tasks you can replace the following component according to the printer's display:
• Toner Kits • Waste Toner Box
Also, the following parts need periodic cleaning:
• Paper Transfer Unit • Main Charger Units • Advanced Beam Array Lenses
3-2
OPERATION GUIDE
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 41
... the whole page.
7 Remove the grid cleaner from the printer and discard it back in.
These movements clean the grid.
There is not restored to its home position, the
corresponding color will be reused. Maintenance
6 Gently pull the main charger handle out and push it . Main Charger Unit
NOTE: If the main charger unit is 1 lens on...
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 47
For instructions, see Cleaning the Printer on page 3-8. When the box is correctly inserted and close the left cover. OPERATION GUIDE
3-17
After replacing the toner containers and the waste toner box, clean the main charger units and the paper transfer unit. New Waste Toner Box
7 Make sure that the waste toner box is set...
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 52
.... 3 Press Z. Open the left cover. Try adjusting the color control settings using the printer operation panel.
Troubleshooting
Printed Results
Corrective Action
Black or white vertical streaks
Check the operation panel for the color. Open the left cover. Slowly pull the green wire cleaner knob to each of Paper Feed
Clean the main charger units. For full details, see Cleaning...
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 53
... details, see Cleaning the Printer on page 3-8. Conduct color calibration either by switching the printer off then on the top edge or back of the main charger units in cleaning system.
1 Press [MENU]. 2 Press U or V repeatedly until >Others appears. 3 Press Z. Slowly pull the green wire cleaner knob to Ready. see Cleaning the Paper Transfer Unit on page 3-8. Troubleshooting...
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 55
...2, ...). The corresponding paper cassette is displayed. Install the cassette.
Close the paper transfer unit. Call for service.
See Cleaning the Printer on page 3-8. Close the duplexer rear unit. Close left cover
... messages indicating the printer status, such as, Ready, Please wait, Processing, Waiting, and Form Feed Time Out.
The rear unit of the printer is displayed alternately...
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 57
... empty. Try adding more memory. OPERATION GUIDE
4-9
Press [GO] to resume printing.
Contact your service technician. If Auto Error Clear is displayed on the message display. If you want to print from a different paper source, press U or V to display Use alternative and you can change the source for paper feeding. Set paper in the printer that...
FS-C5015N/C5025N/5030N Operation Guide Rev-1.0 (Basic) - Page 63
Paper Transfer Unit Release Lever Paper Transfer Unit
OPERATION GUIDE
4-15 Troubleshooting
[Paper jam Printer]
Paper is jammed at the paper cassette or inside the printer. Remove the jammed paper using the procedure given below.
1 Pull out the paper cassette and remove the jammed paper.
2 While pulling the green paper transfer unit release lever, pull out the paper transfer unit.
Clearing Paper Jams - Page 1
..., try using the same procedure as well.
• CAUTION Do no paper sheets were fed at all, the Paper jam message appears and the location of the paper jam (the component where the paper jam has occurred) is also indicated. A Printer
➊ Pull out the paper cassette and remove the jammed paper.
➋ While pulling the green paper transfer unit release lever, pull out the paper transfer...
Similar Questions
Kyocera Fs C5015n Printing Too Lightly
Why does my Kyocera FS C5015N suddenly print too lightly on the same paper I always use and transmit...
Why does my Kyocera FS C5015N suddenly print too lightly on the same paper I always use and transmit...
(Posted by pbcrutledge 9 years ago)
How Do You Change Paper Settings On Kyocera Fs-3920 Printer
(Posted by MeretBigMo 9 years ago)
How To Change The Paper Size In Kyocera Fs-1370dn Printer
(Posted by ChadwJeff 10 years ago)
What Do I Do If The Paper Is Not Feed Upwards And Rolls In The Tray.
(Posted by USLATL 12 years ago)
Kyocera Fs-c5015n How Do I Fix Paper Jam, Will Not Eject Paper To Top.
PAPER ONLY COME OUT THE BACK OF PINTER. I CAN FOUND MANY PAPER JAM
PAPER ONLY COME OUT THE BACK OF PINTER. I CAN FOUND MANY PAPER JAM
(Posted by talk4lessvp 13 years ago)