Kenwood TK-2300-V4P Support Question
Kenwood TK-2300-V4P Support Question
Find answers below for this question about Kenwood TK-2300-V4P - Protalk 2Way 2Watt 4Channel Vhf Radio.Need a Kenwood TK-2300-V4P manual? We have 1 online manual for this item!
Question posted by competentclimber74 on April 8th, 2013
Can't Reset Radio Holding Three Keys And Turning On, Why?
The person who posted this question about this Kenwood product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Kenwood TK-2300-V4P Manual Pages
Instruction Manual - Page 2
... which channel you have
selected and which settings you have made when reassigning key functions and channel settings.
Your Kenwood 2-way Business Radio is a precision device. Treat it with care, and you with 27 VHF operating frequencies (TK-2300) or 89 UHF operating frequencies (TK-3300) and 122 tone/ code settings for each channel allowing you to...
Instruction Manual - Page 4
... the frequency charts on communications frequencies which frequencies you by telephone, and will operate. ii FCC Rules require that all operators using Private Land Mobile radio frequencies obtain a radio license before operating their equipment. QUESTIONS?
Call the FCC Forms Hotline at 1-888-CALL-FCC (1-888-225-5322).
Instruction Manual - Page 5
... to comply with the limits for technical assistance.
ATTENTION: The RBRC Recycle seal found to radio or television reception, which is illegal in a particular installation. For information on Kenwood lithium-...their operating life has expired.
This equipment generates, uses and can be determined by turning the equipment off and on, the user is encouraged to try to correct the ...
Instruction Manual - Page 6
... volume. iv
Notices to the User
◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control.
◆ Illegal operation is punishable by Kenwood....; The charger is aware of, and understands, hazards common to the volume level when turning the squelch off. • Do not place the microphone cable around your neck while ...
Instruction Manual - Page 7
...from the transceiver, switch the transceiver power off in such conditions, it is running. Turn the transceiver power off immediately, remove the battery pack from the antenna covering. When... the airbag inflates, the transceiver may short the battery terminals. • Danger of
radio devices, including but not limited to medical facilities. • Near persons using an ...
Instruction Manual - Page 8
... burst into flame.
• Do not charge the battery near fire, stoves, or other means! Do not carry or store the battery pack in containers holding metal objects (such as a paper clip or wire). If the insulator is melted, the gas release vent or safety function is damaged, or the electrolyte...
Instruction Manual - Page 11
CONTENTS
UNPACKING AND CHECKING EQUIPMENT 1 PREPARATION 2 ORIENTATION 6 BASIC OPERATIONS 8 VOICE OPERATED TRANSMISSION (VOX 9 BACKGROUND OPERATIONS 10 CHANNEL SETUP MODE 11 KEY ASSIGNMENT MODE 20 TROUBLESHOOTING GUIDE 25 ALL RESET MODE 26 OPTIONAL ACCESSORIES 26
UNPACKING AND CHECKING EQUIPMENT
Carefully unpack the transceiver. Supplied Accessories
• Battery charger/ AC adapter (...
Instruction Manual - Page 13
... the antenna in these ways may get hot during ...x 8 mm screws.
Belt clip
Do not use glue which is not installed, its base and turning it may crack the transceiver's back panel.
Note: The antenna is designed to the transceiver.... antenna into the connector on the top of the transceiver by holding the antenna at its mounting location may damage the antenna and degrade your transceiver's performance. ...
Instruction Manual - Page 16
... settings of a
channel, refer to transmit.
PTT (Push to Talk) switch Press and hold, then speak into the microphone to "CHANNEL SETUP MODE" on page 11. • Channel ... the newly selected channel number. To switch the transceiver OFF, turn counterclockwise until a click sounds. Power switch/ Volume control Turn clockwise to page 8. LED indicator For the LED indicator status,...
Instruction Manual - Page 17
... details on how to change the function of the Side 1 key, refer to "KEY ASSIGNMENT MODE" on page 20. The default setting is Scan + Temporary Delete. • For function descriptions and details on how to change the
function of the Side 2 key, refer to "KEY ASSIGNMENT MODE" on page 20. Speaker/ microphone jacks Insert...
Instruction Manual - Page 18
... the microphone using your normal speaking voice. • Hold the microphone approximately 1.5 inches (3 to 4 cm) from your lips.
4 Release the PTT switch to select your desired channel.
• When you receive an appropriate signal, you will hear audio from the speaker. BASIC OPERATIONS
1 Turn the Power switch/ Volume control clockwise to switch...
Instruction Manual - Page 19
... power OFF, press and hold the Side 1 key while turning the transceiver power ON.
3 Continue to hold the Side 1 key until a beep sounds. • The LED indicator lights turn VOX ON/OFF for the...is not connected to the accessory terminal of the radio (from 1~10 or Off). • Press the Side 2 key to turn orange. • When the Side 1 key is released, the transceiver will announces the VOX ...
Instruction Manual - Page 23
... OPERATING FREQUENCIES To change the operating frequency of a channel: 1 With the transceiver power OFF, press and hold the PTT
switch and Side 1 key while turning the transceiver power ON. • Continue to hold the PTT switch and Side 1 key until the LED
lights orange and the transceiver announces "Self". 2 Release the PTT switch and Side...
Instruction Manual - Page 26
...table on pages 17 and 18. • Press and hold the PTT switch and Side 1 key until the LED lights orange and the transceiver announces "Self".
2 Release the PTT...channel:
1 With the transceiver power OFF, press and hold the PTT switch and Side 1 key while turning the transceiver power ON. • Continue to hold the Side 1 or Side 2 key to hear your channel. If a call containing a different...
Instruction Manual - Page 29
Note: The transceiver will automatically return to your channel settings: 1 With the transceiver power OFF, press and hold the PTT
switch while turning the transceiver power ON. • Continue to hold the PTT switch until the LED lights orange and
the transceiver announces "Confirm". 2 Release the PTT switch.
• Transceiver announces the channel table...
Instruction Manual - Page 31
... functions of the Side 1 and Side 2 keys: 1 With the transceiver power OFF, press and hold the Side 1
and Side 2 keys while turning the transceiver power ON. • Continue to hold the Side 1 and Side 2 keys until the LED lights
orange and the transceiver announces "Setup". 2 Continue to press and hold the key to be reprogrammed
(either the Side...
Instruction Manual - Page 32
... normal operation. ■ Monitor Momentary Press and hold this key for 1 second to deactivate QT or DQT signaling. To make a call, press the key programmed as Key Lock except that you are calling. Without Status Memory, when the transceiver power is turned OFF and then ON again, the Key Lock function will be cancelled. ■ Monitor...
Instruction Manual - Page 33
... an undesired channel, you can remove that channel from the scanning sequence by pressing and holding this key for 1 second.
23 ■ Scan Scan is listening to your channel will be unable...other party that channel from the scanning sequence by pressing and holding this key for 3 seconds.
■ Scrambler Press this key to start scanning the transceiver channels. If the QT/DQT does ...
Instruction Manual - Page 34
... power OFF, press and hold this key for 2 seconds while turning the transceiver power ON. • When the LED lights orange, release the Side 2 key. Each time you press this key to change the transmit power to lock the transceiver keys. ■ Super Lock (Side 1 key default) Super Lock locks the same keys as Key Lock. A confirmation tone will...
Instruction Manual - Page 36
... power OFF, press and hold the PTT
switch, the Side 1 key, and the Side 2 key while turning the transceiver power ON. • Continue to hold the keys for 2 seconds, until the LED lights
orange. 2 Release the keys.
• The keys must be released within 1 second after the LED lights orange, otherwise All Reset Mode will reset all channels to their...
Similar Questions
Requirements That I Need To Bring For My Kenwwod Radio Change Frequency
My agency shift a 7 kenwood radio but we try to check it and we found out that the 3 kenwood radio w...
My agency shift a 7 kenwood radio but we try to check it and we found out that the 3 kenwood radio w...
(Posted by luzcaadan 10 years ago)
Dqt
When I press the PTT switch and the Side 1 button and turn on the power nothing happens. Any idea?
When I press the PTT switch and the Side 1 button and turn on the power nothing happens. Any idea?
(Posted by p56 10 years ago)
Programming Software For Kenwood Tk3230 Radio
Where Can I Find Programming Software For Kenwood Tk3230 Business Radios
Where Can I Find Programming Software For Kenwood Tk3230 Business Radios
(Posted by rafterman1950 10 years ago)
Program A Portable Radio
I have a TK2302V portable radio that needs to have four channels programmed into it. I am located...
I have a TK2302V portable radio that needs to have four channels programmed into it. I am located...
(Posted by ka2ajh 12 years ago)
Radio Says 'protect' And Doesn't Work.
(Posted by russsur 12 years ago)