Kenwood KSC-SW11 Support Question
Kenwood KSC-SW11 Support Question
Find answers below for this question about Kenwood KSC-SW11.Need a Kenwood KSC-SW11 manual? We have 1 online manual for this item!
Question posted by colinnewman7 on July 31st, 2017
On Off
can you please tell me if the light should stay on when you turn it off on the kenwood dpx 5000bt
Current Answers
Related Kenwood KSC-SW11 Manual Pages
Instruction Manual - Page 2
...car can cause shorts or fires.)
• When extending the ignition, battery, or ground wires, make sure that electrical equipment such as the brake lamps, turn...mounting. Sharing the negative wire of the speaker or grounding speaker wires to the vehicle instruction manual.
&#..., Kanagawa, 221-0022, Japan
EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN...
Instruction Manual - Page 3
...Name
1
Remote control (5 m / 16 ft)
2
10-pin connector cord (5 m / 16 ft)
3
Speaker cord (4.3 m/ 14 ft)
4 Fixture A
5 Fixture B
Outside Shape
Quantity 1 1 1
No. Part Name...illumination on the remote control unit do not light up. • Do not insert the ...SPEAKER INPUT terminal REMOTE terminal
■ Connecting the remote control unit
1 Remote control
Lights in blue.
Parts included...
Instruction Manual - Page 4
...the instruction manuals for effective car stereo enjoyment.
Blue/White
3 Speaker cord
If buzzing noise is heard from the speakers when the engine is ...speaker Left Right
Do not distribute the cords in the center unit, connect the blue/ white wire to the rear output, as this terminal is no power control terminal in the paths where they may result. Gray/Black Gray White
KSC-SW11...
Instruction Manual - Page 5
...to the RCA
jacks for effective car stereo enjoyment. Fuse 10A
Center unit (SUB WOOFER OUT, Non-fader output)
KSC-SW11
If there is not used.
5 English
Turning the power ON
without connecting ...Car fuse box
Ignition key switch
Car fuse box (Main fuse)
Battery
2 10-pin connector cord
RCA cord (Commercially available parts)
LINE IN
Blue/White
If buzzing noise is heard from the speakers...
Instruction Manual - Page 6
...ø 3.6 mm screws. Be careful so that there is connected preliminary.
Installation
Before fixing the speaker in place with fixture B 5 and fix in its position, be sure to check the sound ...holes for ø 3.6 mm screws on the sheet metal section of the vehicle , and attach the speaker unit to the subwoofer installation location. Drill the pilot holes for ø 3.6 mm screws on the ...
Instruction Manual - Page 7
..., the illumination lights.
Otherwise, the product may result. Remove dirt from the heater.
Turn the FREQUENCY control knob to the desired level. This product is 0º (positive).
3 Turn the VOLUME control knob to adjust the low frequencies to adjust the balance between the bass from the rear speakers and the bass from this unit...
Instruction Manual - Page 8
... 16 V) Maximum current consumption 8.5 A Fuse capacity 10 A Sensitivity 110 dB (In car) External size Width : 280 mm (11")
Height : 70 mm (2-3/4") Depth :...control is set to the MIN position.
• The speaker cords are connected improperly.
• Connection terminals are connected...guide
Often, what appears to be turned on (illumination does not light).
Remedy
• Check the (+)/(-)...
Similar Questions
Wired Remote
I have a kenwood jack-sw11 but have lost the wired remote for it. Can I still use it without the rem...
I have a kenwood jack-sw11 but have lost the wired remote for it. Can I still use it without the rem...
(Posted by jesleek2019 1 year ago)
Color code Wiring diagram For a 07 Mitsubishi Galant Car Stereo System
Color code Wiring diagram for a 07 Mitsubishi Galant car stereo system 2 a kenwood dnx5120 just need...
Color code Wiring diagram for a 07 Mitsubishi Galant car stereo system 2 a kenwood dnx5120 just need...
(Posted by GinaMartin 3 years ago)
Wiring Diagram On A Kenwood Dnx-7100 Double Din Car Stereo
I am trying to install a kenwood dnx double din car stereo but I dont know what some connections are...
I am trying to install a kenwood dnx double din car stereo but I dont know what some connections are...
(Posted by mrtowman 9 years ago)
My Kdc 122p Car Stereo Stopped Working After The Battery Was Changed. No Sound?
The shop changed out my car battery and my stereo hasn't played since. The display lights up but t...
The shop changed out my car battery and my stereo hasn't played since. The display lights up but t...
(Posted by nucsta 12 years ago)
How Do I Use The Remote To Set Am And Fm Channels On My Car Stereo?
My car stereo was replaced by a dealer with a new kenwood model, and the ramote was used to set the ...
My car stereo was replaced by a dealer with a new kenwood model, and the ramote was used to set the ...
(Posted by kenna 13 years ago)