Home » Kenwood » Car Stereo Amplifiers » Kenwood KAC-X811D

Kenwood KAC-X811D Support Question

Find answers below for this question about Kenwood KAC-X811D.
Need a Kenwood KAC-X811D manual? We have 1 online manual for this item!

Kenwood Overview Questions Manuals Reviews Videos Research

Question posted by jcbullet on February 17th, 2012

How Do I Keep This Amp From Shuting Down After A Few Min. Of Play @ A 1 Ohm Load

How do I keep this amp from shuting down after a few min. of play at a 1 ohm load? I have four 12" kenwood 3013ps powered by this amp.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Kenwood KAC-X811D Manual Pages

Instruction Manual - Page 1

KAC-X811D KAC-PS811D SUBWOOFER POWER AMPLIFIER 7 page 2-9 INSTRUCTION MANUAL © B64-2794-00/00 (MV)

Instruction Manual - Page 2

... power of the amplifier will cause smoke to be used , use because the surface of the amplifier. NOTE • If you of operation range. The protective fuse should be working right, consult your Kenwood ... wire for this unit. NOTE • The LX AMP and the sensor unit cannot be used , calculate the combined impedance of the car chassis that are going to be emitted as well as...

Instruction Manual - Page 3

... wires. 5.Connect the power wire, power control wire and grounding wire... following this unit in a location which it may be damaged. • Install this order. 6.Install the installation fittings in the below locations; (Unstable location, In a location that there is nothing hazardous on top of the unit. • The surface temperature of the amplifier...

Instruction Manual - Page 4

...connection CENTER UNIT To KENWOOD disc changer/ External optional accessory Power control wire Control cable (option) �� Master amplifier Extension wire* �... can cause this limit, you cannot control amps from the Center Unit. • If you assign ID number "8" or "9" to 7 Slave amplifiers. You must connect any of them at ...

Instruction Manual - Page 5

...with a minimum impedance of 1 ohm, connect � speakers with 1-ohm or higher impedance to connect it as Slave amplifiers. NOTE Controls the unit power. Be sure to these numbers...of the center unit. �� % AMP CONT (amplifier control) switch �� ˃ ��...

Instruction Manual - Page 6

... hold down the [3] button 3 or more seconds during ID number display ("AMP"), message "MEMO" is extended by 20%. Amplifier Control System � �� ...is displayed. "VOLT"/"CURR"/"TEMP"/"FAN" is displayed. Separate Amp Control You can recall the value when message "LOAD" is displayed. 4 Exit Menu mode Press the [MENU]...

Instruction Manual - Page 7

... item You can control the sound by controlling amplifiers from Center Unit You can set a value of each item on the Center Unit. "AMP × E-02"/"AMP × COND E-02" NOTE Turn the POWER switch Off and release the protection. Indicates the source voltage (V). "AMP × E-03"/"AMP × COND E-03" When the speaker cord is...

Instruction Manual - Page 8

... observed on the spectrum analyzer disappears. The band reject filter can be • The AMP Control of the amplifier has been changed by referring to "Protection function". • Replace the fuse and use... AMP Control mode of the Center Unit. • Always set to "0". • After you feel through your unit may be the result of the Center Unit first, then turn Off the POWER switch...

Instruction Manual - Page 9

... output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Input Impedance ...10 kΩ Audio Section...KAC-PS811D Max Power Output...1600 W Rated Power Output (+B = 12.0 V) (4 Ω) (20 Hz - 200 Hz,...output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Input Impedance ...10 kΩ Amplifier Control Section (EQ KAC-X811D/PS811D Bass frequency ...60 / 80 / 100 / 200...