Kenwood KAC-X520 Support Question
Kenwood KAC-X520 Support Question
Find answers below for this question about Kenwood KAC-X520.Need a Kenwood KAC-X520 manual? We have 1 online manual for this item!
Question posted by corneliuschris24 on November 11th, 2012
Light
Why is my light blinking yellow when I turn it up?
Current Answers
Related Kenwood KAC-X520 Manual Pages
Instruction Manual - Page 1
...for information or service on the warranty card, and in the space provided below. Model KAC-X520/PS520 Serial number
© PRINTED IN JAPAN B64-2277-00 / 01 (KM / ... serial number, found on the back of the unit, in the spaces designated on the product. KAC-X520 KAC-PS520
POWER AMPLIFIER 7 page 2-13
INSTRUCTION MANUAL
AMPLIFICATEUR DE PUISSANCE 7 page 14-25
MODE D'EMPLOI
AMPLIFICADOR DE POTENCIA...
Instruction Manual - Page 2
...metal tools) inside the unit. • If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. • Do not touch the unit during ... cause harmful interference unless the modifications are expressly approved in the ACC ON position without turning the engine ON, it after starting the engine.
The user could lose the authority ...
Instruction Manual - Page 3
...opposite side such as the brake lamps, turn signal lamps and windshield wipers operate normally. Blocking these openings will inhibit the cooling of the amplifier will not come into contact with driving,... careful not to heat will become hot during use. Attach the unit. 3. Install the amplifier in the below locations; (Unstable location, In a location that interferes with it may be...
Instruction Manual - Page 4
... this switch is blinking.
4 English The speaker output is automatically turned monaural (L+R) and the bass boost function is activated.
9 HPF FREQUENCY control Sets the cutoff frequency when the FILTER switch is set to page 5)
6 B.M.S. Set to this position and make bridged connections to use as a stereo amplifier. • MONO (Lch) position: Amplifies the signal input...
Instruction Manual - Page 5
... the B.M.S. • The color blinks yellow
When the power voltage is worn. -
If the indicator doesn't quit blinking, contact your Kenwood dealer. • The color blinks red When the inside of the...the variable color button. • The color blinks blue - When the battery wire is overheating. • The color blinks green - NOTE
Turn the power OFF and release the protection.
English ...
Instruction Manual - Page 6
... be connected, ensure that the combined impedance is 2Ω or greater for each channel. • Bridged Connections: When you wish to use the unit as a stereo amplifier, stereo connections are used. (Make connections to the LEFT channel 9 and the RIGHT channel · SPEAKER OUTPUT terminals.) The speakers to use the unit as a highoutput...
Instruction Manual - Page 7
...the battery.
2CAUTION • If sound is not output normally, immediately turn power off and check connections. • Be sure to turn the power off before changing the setting of any switch. • If... speaker wires to the metal body of the car can cause this order. 6. English 7 ■ Installation procedure Since there are touching the car body. Connect the power wire, power control ...
Instruction Manual - Page 8
...of 11mm from the battery.
EXT.AMP.CONT. (external amplifier control) terminal ( 1.
Do not turn the power on if the ground wire is running, ...; Connect the ground wire to a metal part of the car chassis that acts as the unit's fuse capacity or somewhat larger... OFF ON
B.M.S. OFF
REMOTE +12dB
FILTER OFF
HPF LPF
(
OPERATION STEREO MONO(L ch)
GND
LINE IN LINE OUT EXT.AMP.CONT.
While...
Instruction Manual - Page 9
...are going to be connected should be used, calculate the combined impedance of the speakers that are going to the amplifier.
2Ω
2Ω 4 Ω
8Ω 8Ω
4 Ω Combined impedance
4Ω 4Ω...then connect suitable speakers to be connected should be 2Ω or greater (for stereo connections), or 4Ω or greater (for bridged connections). Use of speakers ...
Instruction Manual - Page 10
...
CENTER UNIT
¡
L
L
L
RR
Left speaker (Bridged)
RL R
™
INFRASONIC
1
¡ OFF ON
™
B.M.S.
2
OFF REMOTE +12dB
L
Right speaker (Bridged)
R
FILTER
3
OFF HPF LPF
OPERATION
4
STEREO MONO(L ch)
■ 2-channel + Subwoofer system
CENTER UNIT
¡
L
L
RR
LINE OUT
L
L
RR
™
Left speaker (High pass) Right speaker (High pass)
Subwoofer (L + R) (Bridged...
Instruction Manual - Page 11
... impedance must be passed. ■ Tri-mode CENTER UNIT
L
L
RR
L C
(High pass)
C
Subwoofer (L + R) (Bridged)
INFRASONIC
B.M.S.
1
2
OFF ON
OFF REMOTE +12dB
FILTER
3
OFF HPF LPF
OPERATION
4
STEREO MONO(L ch)
●Principle of Tri-mode Method of frequency band division using speakers with an impedance of 4 ohms. Prepare commercially-available coil and capacitor...
Instruction Manual - Page 12
Troubleshooting Guide
What might appear to be a malfunction in the car body.
• The switches may be set improperly.
•...speaker cord is not pinched by anything.
• Set switches properly by referring to "System examples". The external amplifier controller (B.M.S.) will not work.
• The B.M.S. Adjust the control correctly referring to the correct position.
of ...
Similar Questions
I Have A Kenwood Excelon Kac-x20 Amp When It's Hooked Up An U Like Turn Switch
OK I got a kenwood excelon KAC-X20 amp an u first hook it up or if it was hooked up if u first turn ...
OK I got a kenwood excelon KAC-X20 amp an u first hook it up or if it was hooked up if u first turn ...
(Posted by ottjones91 1 year ago)
Amplifier Sound Cutting
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
my kenwood power amplifier kac 6402 sound is cutting imediately 2 minutes after starting the vehicle...
(Posted by marksuzyo07 7 years ago)
I Have A 400w Car Amp With No Instalation Manual The Model Is Kac-6202 Can You M
(Posted by worz 11 years ago)