Home » JVC » Home Theater Systems » JVC RX-5060B

JVC RX-5060B Support Question

Find answers below for this question about JVC RX-5060B - AV Receiver.
Need a JVC RX-5060B manual? We have 1 online manual for this item!

JVC Overview Questions Manuals Reviews Videos Research

Question posted by dennisk on June 9th, 2011

Jvc Rx5060b Receiver Not Switching On

MY JVC receiver was operated at a very high volume and it switched itself off. When plugged into mains the standby button lights up but when the power button is pushed the standby button goes off only to light up again a few seconds later.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related JVC RX-5060B Manual Pages

Instructions - Page 2

... STANDBY lamp lights red. • When the unit is provided to call the CATV system installer's attention to the point of the NEC which provides guidelines for proper grounding and, in the literature accompanying the appliance. ATTENTION Afin d'éviter tout risque d'électrocution, d'incendie, etc.: 1. Disconnect the mains plug to correct the interference by JVC...

Instructions - Page 3

... 23 Reproducing Theater Ambience 23 Introducing the Surround Modes 23 Activating the Surround Modes 25 7 Auto Surround Function 25 7 Activating the Surround Modes Manually 25 Using the DSP Modes 26 Reproducing the Sound Field 26 Introducing the DSP Modes 26 Activating the DSP Modes 27 COMPU LINK Remote Control System ......... 28 Operating JVC's Audio...

Instructions - Page 5

..., 29) Number buttons for operating audio/video components (29 - 32) 3 SOUND button (22, 29) 4 REC PAUSE button (30, 32) 5 Source selection buttons (9, 10) TAPE/CDR, CD, DVD, AUX, FM/AM, TV SOUND, VCR 6 FM MODE button (15, 29) 7 SURROUND button (25, 29) 8 DIMMER button (12, 29) 9 TV/VIDEO button (30, 31) 0 VCR CH +/- TV CATV A/V CONTROL STANDBY/ON RECEIVER TEST 1 FRONT...

Instructions - Page 6

...; Use the correct type of batteries. English Getting Started Do not connect the AC power cord until all components. • Read the manuals supplied with the components you have... antenna. 2 Connect a 75 Ω coaxial cable (with the receiver. If the remote control cannot transmit signals or operate the receiver correctly, replace the batteries. This section explains how to connect audio...

Instructions - Page 8

... about the connection and the COMPU LINK remote control system. Connecting the subwoofer You can place it in front of the viewing area. well above ear level (60 cm to the audio right jack. Analog Connections Audio component connections Use the cables with RCA pin plugs (not supplied). • Connect the white...

Instructions - Page 10

... For DVD player - When you want to operate the CD player or CD recorder using a digital optical cable (not supplied). Plug the power cord into an AC outlet, make sure that ...• When you unplug the power cord. - Set the digital input (DIGITAL IN) terminal setting correctly. When a power failure occurs. Digital Connections By connecting the receiver and the source component through the...

Instructions - Page 11

... Modes" (page 27). Daily Operational Procedure Selecting the Source to Play When you have the same and similar names/marks. The STANDBY lamp goes off the power (into standby mode), press STANDBY/ON (or STANDBY/ON remote control) again. To turn off . You can turn off the power completely, unplug the AC power cord. 9 VOLUME Current volume level appears. Current source...

Instructions - Page 12

... source are coming into this receiver. On the remote control: To increase the volume, press VOLUME +. How to show the incoming signals. To decrease the volume, press VOLUME -. Sounds come out of "L," "C," "R," "LS," and "RS" light up, when the corresponding speakers are coming into this receiver. R: • When digital input is selected: Lights up when the right channel...

Instructions - Page 13

... its high volume may come in . : Lights up on the next page 11 The DIGITAL AUTO indicator lights up when... digital input mode is canceled, the indicator goes off. No indicator lights up on page 12. 2 Press INPUT ...lights up when the receiver cannot recognize the digital signal format of the source selection buttons (DVD, TV SOUND, CD, TAPE/CDR*) for the sources you press the button...

Instructions - Page 15

...volume level, Midnight Mode (see page 19), Equalization patterns (see page 22), Surround modes and DSP modes (see pages 23 to the VCR jacks at whatever sound level you change the time remaining until the shut-off time: Press SLEEP once. When the shut-off time comes, the receiver turns off the power... the recording. The following basic operations are automatically recalled. Using the ...

Instructions - Page 16

... MONO" as the FM reception mode). • When you hold and then release the button in step 2, the frequency keeps changing until a station is tuned in to select a ...VOLUME TUNED STEREO AUTO MUTING VOLUME The last received station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display. • When an FM stereo program is received, the STEREO indicator also lights...

Instructions - Page 25

... and enables stereo surround sound. • This receiver provides three types of Dolby Laboratories. 23 You...developed by Dolby Laboratories is activated, the PRO LOGIC indicator lights up on the display. As such, the sound movement...the cutoff frequency of Surround modes automatically. Reproducing Theater Ambience In a movie theater, many speakers, sound localization and sound movement...

Instructions - Page 26

... create the surround effect through the digital input, the indicator lights up on . Uncompressed digital audio data used for reproducing at quantization of Digital Theater Systems, Inc. 24 It allows two independent channels (called main channel and sub- than-CD sound quality" into the home. • When DTS 96/24 signal is now adopted in...

Instructions - Page 30

.... The source changes on the receiver. English COMPU LINK Remote Control System The COMPU LINK remote control system allows you do not press the record (¶) button and pause (8) button at the same time, the synchronized recording feature will not operate. 3 Press the play (3) button on the CD player. Plug the AC power cords only after all connections are...

Instructions - Page 31

... front speaker output level. To start recording, press this button then 3. Operating Audio Components IMPORTANT: To operate JVC's audio components using the supplied remote control: • You need to the beginning of the current (or previous) track. MUTING: Turn on or off the receiver. ANALOG/DIGITAL: Switch the analog and digital input alternately. SLEEP: Set the...

Instructions - Page 32

... CD changer After pressing CD-DISC, you can do the following operations using the supplied remote control: • Some JVC's VCRs can accept two types of the control signals- VCR You can always perform the following operations: STANDBY/ON VCR: Turn on the receiver. • Refer also to the manuals supplied with the discs ENTER...

Instructions - Page 33

... converter 1 Set the TV/CATV selector to "CATV." 2 Press and hold STANDBY/ON TV/CATV. 3 Press TV SOUND. 4 Enter a manufacturer's code using buttons 1 - 9, and 0. TV/CATV CH +/-: Change the channels. TV VOLUME +/-: Adjust the volume. After pressing TV SOUND, you can perform the following operations on the TV: 1 - 9, 0, 100+ (+10): Select the channels. The 10...

Instructions - Page 34

...operations on and off , you can perform the following operations on the VCR: STANDBY/ON VCR CH +/-: VCR: Turn on the VCR. To start recording, press this remote control cannot operate the equipment. 32 Manufacturer JVC...fast reverse for some models). After pressing DVD, these buttons can perform the following operations on the DVD player: STANDBY/ON DVD: Turn on the DVD player: 3: 4:...

Instructions - Page 35

PROBLEM The display does not light up after turning on the front panel to turn off the receiver, then check the speaker wiring. Remote control does not work . An incorrect antenna is connected, set "SUBWOOFER YES" so that the sounds come out of high volume. SOLUTION Plug the power cord into standby mode). Press MUTING to cancel the...

Instructions - Page 71

JVC Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

FAQ - Audio/Components & Home Theater Systems
... used in the United States is different than the volume when watching my TV, why? Or, you hook...the "Box" to your Television. You will cause the unit's power supply to the receiver. Some cable/satellite boxes and TV’s have the option of...Home Theater System. You have a setting for audio output setting. work harder and operate at a higher temperature than the United...
FAQ
Audio/Components & Home Theater Systems Mobile Navigation: KW-NT3HDT Audio (Soundbar TH-BA1) Mobile Navigation: KD-NX5000/KW-NX7000 Audio-Shelf & Portable Mobile Navigation: KW-NT1 Blu-ray Disc Player: XV-BP1 Mobile Navigation/KV-PX9 eAVINU Everio/High Definition (GZ-HM200,GZ-HM400,GZ-HD300,GZ-HD320) Picsio GC-FM1 Everio/High Definition (Archived and...
FAQ - Audio/Components & Home Theater Systems
...have the option of connection. A variable output setting will cause the unit's power supply to your receiver. It can be used in the United States are 110 Volts at 50 Hz...Television. Audio/Components & Home Theater Systems Will my JVC audio equipment designed for use in the United States. Most overseas countries use different voltages and cycles than the volume when watching my TV, ...