Husqvarna 1827EXLT Support Question
Husqvarna 1827EXLT Support Question
Find answers below for this question about Husqvarna 1827EXLT.Need a Husqvarna 1827EXLT manual? We have 2 online manuals for this item!
Question posted by dljoyce on February 13th, 2021
Won't Start. Changed The Spark Plug, Fresh Gas, Just Won't Turn Over.
Changed the spark plug, fresh gas, just won't turn over. First time I'm running it this year. Had it serviced last year, should be in great working condition. Not sure where to go from here
Current Answers
Related Husqvarna 1827EXLT Manual Pages
Owners Manual - Page 1
Operator's Manual
1827EXLT
Gasoline containing up to 10% ethanol (E10) is acceptable for use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
532 44 35-56
Please read the owner's manual carefully and make sure you understand the instructions before using the machine.
English The use in this machine.
Owners Manual - Page 2
...plug in serious injury. Caution should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Keep the area of operation clear of all persons, small children and pets at all persons, particularly small children.
4. Thoroughly inspect the area where the equipment is to a running...from the spark plug, disconnect the cord on clothing, change clothing ...
Owners Manual - Page 3
...to be sure the equipment is to cool before storing in place and working condition.
2. Disconnect the spark plug wire and keep a firm hold on the handles. never run the engine indoors, except when starting the ... starting the engine and for transporting the snow thrower in deep snow, be stored for long periods of time in or out of injury associated with fuel in safe working ...
Owners Manual - Page 4
... 50°F) SAE 5W-30 (below 32°F)
Oil Capacity:
38 Ounces (1,12 Liters)
Spark Plug: Gap:
Champion F6RTC 0.030" (0,762 mm)
CUSTOMER RESPONSIBILITIES
• Read and observe the safety..., well-trained technicians and the proper tools to assemble and maintain your nearest authorized service center. The instructions will enable you cannot easily remedy, please contact your snow thrower...
Owners Manual - Page 9
DANGER OR WARNING
PRIMER
FORWARD
REVERSE
READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.
INSERT TO START
AND RUN, PULL OUT TO STOP. Compare the illustrations with your snow thrower or in literature supplied with the location of various controls and adjustments. OPERATION
KNOW ...
Owners Manual - Page 10
...
ELECTRIC START
BUTTON
AUGER CONTROL LEVER
POWER CORD PLUG
DISCHARGE CHUTE CONTROL LEVER
DRIVE SPEED CONTROL LEVER
CODNERTFRELMOELOCTLTEEOVRERTCROANCDTTRRIIOOVNEL LEVER
CHUTE DEFLECTOR
LH TURN TRIGGER
CLEAN...
Traction drive control lever - Electric start and run.
ON / OFF switch - Remove when snow thrower is not in use when starting engine. tion the snow is thrown....
Owners Manual - Page 11
...ADJUSTMENT OF SNOW THROWER
TO TRANSPORT (See Figs. 11 & 12)
When transporting your snowthrower, be sure to disengage the transmission by placing freewheel control into FREEWHEEL position (See Fig. 11) and height ... oil to stop throwing snow.
As you run your foot, push down on the pedal, tilt the unit to start the engine. You do not turn) safety ignition key to prevent unauthorized use choke...
Owners Manual - Page 12
...See Fig. 18)
In certain snow conditions, the discharge chute may become clogged,... control lever.
• To change the discharge chute position, press ...throw snow a short distance; Be sure lever springs back and locks into ...are starting . set the deflector higher to dislodge the blockage.
Disconnect the spark plug ..., make certain all times including startup. Do not use to start a warm engine. ...
Owners Manual - Page 13
... ground. When it may be sure skid plates are adjusted to lowest...; To turn right -
Shut off engine and wait for current surface conditions.
DRIVE SPEED...turn left -
It is uneven. Use a middle position if the surface to be reversed, providing additional service before requiring replacement. LH TURN RH TURN... bar is not adjustable, but is running. When a trigger is controlled by ...
Owners Manual - Page 14
... gasoline.
Serious personal injury or damage to the "OFF" position.
14 Use fresh, clean, regular unleaded gasoline with oil.
1. Empty the gas tank, start the engine and let it clicks.
Plug the other end of 87 octane.
household current.
• Be sure your snow thrower has been shipped from the factory already filled with a minimum...
Owners Manual - Page 15
...turn the engine, proceed as follows:
1. Keep the extra safety ignition key in this section of this time the snow is between 15° and 50°F.
BEFORE STOPPING
Run the engine for current snow conditions... pull as possible.
2. Disconnect the power cord from the receptacle first, then from starting. Engine will help dry off the engine.
• Clean the entire snow thrower ...
Owners Manual - Page 16
A new spark plug will need to be made periodically to the operator.
Check for wear.
Check engine oil level.
2. LUBRICATION CHART
➀ SAE 30 Motor Oil ➁ See "ENGINE" in this manual. Some adjustments will help your engine run better and last longer.
• Follow the maintenance schedule in the Service and Adjustments section of...
Owners Manual - Page 17
...).
7. Install drain plug and tighten securely.
5. Be sure to the proper level
at "FULL" line on your expected operating temperature. Pour slowly. Wipe off any spilled oil. SPARK PLUG
Replace spark plug at least once a year if thrower is if service has been performed on oil.
Water in engine can result in a suitable container.
4. The only time the lubricant...
Owners Manual - Page 18
... if the capscrews have completely stopped.
4. SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury, before performing any other components. Be sure the on/off switch is engaged, check to stop .
2. Make sure the augers and all moving parts have sheared. 18
FRAME
FIG. 25
SCREWS Disconnect spark plug wire from the operator.
SNOW THROWER
TO...
Owners Manual - Page 19
...and inside the groove of auger pulley only.
10. Make sure belt is recommended that both the auger and traction drive belt...service center/department. Belt must be replaced by original equipment manufacturer (OEM) belts available from wear, they should fall during the belt changing...the snow thrower should be replaced at the same time. Remove bolt, flat washer securing pulley to the ...
Owners Manual - Page 20
... track from axle. TO ADJUST CABLE TENSION (See Fig. 28) Adjust cable tension by turning the adjuster turn the short section to 7,000 feet (2,134 meters). If you think the engine-governed high speed needs adjusting, contact a qualified service center, which is factory set for proper engine speed. ENGINE SPEED Never tamper with...
Owners Manual - Page 21
... the mix ratio found on a furnace, water heater, clothes dryer or gas appliance. Pull recoil starter handle slowly a few times to protect it from one ounce (29 ml) of oil through spark plug hole into cylinder.
3. WARNING: Never store the snow thrower with new spark plug. Replace if necessary.
5. Touch up all rusted or chipped paint...
Owners Manual - Page 22
... muffler.
4. Loose parts or damaged augers or 1. remains, contact an authorized service center/department.
1. Contact an authorized service center/department.
4. Remove snow and ice build up in 4. Clogged discharge chute.
3. Fill fuel tank with fresh, clean gasoline.
4. Engine is worn.
2. Replace spark plug.
10. Remove ice and snow on and around fuel tank cap. Empty...
Parts List - Page 2
inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. MODEL NO. 1827EXLT (96193007700), PRODUCT NO. 961 93 00-77
5
15 14
4
11 6
11
16
12
13 11
3 12
10
11 7
8
17
1
9
37
2
9 9
33
37
32
34
30
...
Parts List - Page 3
...damage your snow thrower and void your warranty.
3 REPAIR PARTS
AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1827EXLT (96193007700), PRODUCT NO. 961 93 00-77
KEY NO.
1 2 3 4 5 6 7 8 9 10 ...18 X .625 IMPELLER HUB IMPELLER SLEEVE NUT 3/8-16 CARRIAGE BOLT SCREW 13-16 X .625 PLUG GEARBOX COVER RH GASKET SEAL BEARING THRUST WASHER 1.00 WORM GEAR AUGER SHAFT SQUARE KEY BEARING THRUST...
Similar Questions
My 390xp Fluids It Self Every Time Start It.it Opp Ores Gas Out The Mufler
(Posted by billyakers8 3 years ago)
I Have A 128ld And It Won't Start. New Spark Plug. No Fire Still
(Posted by Anonymous-153427 8 years ago)
Need To Change Spark Plug On Snowblower Model 1830hv
(Posted by kayakzzz 9 years ago)
Can't Start Put New Plug In, Fuel Getting To Piston Good Spark Still Won't Start
576xp won't start ,new plug ,fuel getting through,nothing ,fitted new piston and pot ,still won't st...
576xp won't start ,new plug ,fuel getting through,nothing ,fitted new piston and pot ,still won't st...
(Posted by Davidrigby 9 years ago)