Hunter 90021 Support Question

Find answers below for this question about Hunter 90021.
Need a Hunter 90021 manual? We have 1 online manual for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by lsmeragliuolo on May 5th, 2020

Replacement Part

Greetings, The fan only works on high speed; I need a new switch.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by techyagent on May 5th, 2020 11:41 PM

This answer was accepted by the poster of the original question.

techyagent

Member since:
June 17th, 2014

Points: 4,799,790

1,110
points

Needs a three speed new switch.you should get one at an electrical shop. Assuming that the unit was wired properly from the factory and without being able to look at the switch I would have to agree that the switch is bad. The different speeds are obtained by having a different winding for each speed. If the unit was wired properly at the factory and never had three different speeds then the switch is not rotating between all the contacts. The switch should only be a couple of dollars and would certainly be a cheap solution to try. You can check the existing switch by removing it from the circuit completely and checking the continuity with a DMM from the input to each output as you switch it. Continuity should move from one to two to three. If not the switch is bad. If the switch checks out OK then you have a bad winding in the fan and probably need a new unit.

Thanks

Techygirl

Related Hunter 90021 Manual Pages

Owners Guide - Page 1

® C ENTURY High Performance Oscillating Fan The OWNER'S GUIDE FOR MODELS 9002X & 9702X 41479-01 01/06/2005 41479-01 Rev 01-06-05.pmd 1 1/6/05, 5:06 PM

Owners Guide - Page 2

...speed...properly grounded. CAUTION When using this fan with a damaged cord or plug, ... NOT put fan in any other objects through the grill when the fan is suitable for..., cooking or any manner. 12. The fan should always be placed on a flat, stable... a dry surface. 14. DO NOT place fan or any other heating appliances. 17. The power...NOT use this fan. 2. NEVER insert fingers, pencils or any ...

Owners Guide - Page 3

... all shipping materials are some the features you will enjoy with your fan: • An attractive design that enhances any decor • A powerful Hunter motor for maximum air flow • Three speeds to adjust your comfort level Before installing your fan, record the following information for warranty assistance. NOTE: It is best to...

Owners Guide - Page 4

... adapter must be plugged into the outlet. 3. Please return it into any are found, the appliance should not be serviced and the line cord replaced. DO NOT use any damage, if the appliance works intermittently or stops working entirely. DO NOT operate appliance if the line cord shows any other type of outlet.

Owners Guide - Page 5

... the oscillation knob up. Adjust to the desired speed setting: O (off), I (low), II (medium), III (High). 5. Turn the fan "ON" or "OFF" by the cord. 2. To make the fan oscillate, push the oscillation knob down. Handle Oscillation Knob Motor Housing Up/Down Adjustment Screw Base Power/Speed Control Switch FIGURE 3 41479-01 01/06/2005 5 41479...

Owners Guide - Page 6

...Speed Control Switch FIGURE 4 6 41479-01 01/06/2005 41479-01 Rev 01-06-05.pmd 6 1/6/05, 5:06 PM First, replace the blades. DO NOT allow water or any other liquid to wipe the remaining fan... may be used to remove the hook from dust accumulation. MAINTENANCE This fan is needed. This fan requires little maintenance and contains no user serviceable parts. Contact qualified service ...

Owners Guide - Page 7

... Web site at http://www.hunterfan.com. 41479-01 01/06/2005 7 41479-01 Rev 01-06-05.pmd 7 1/6/05, 5:06 PM Disassemble and clean fan before storing. 2. Keep the original packaging for the purpose of motor housing to the desired angle and tighten the screw. SOLUTION • Loosen the screw...