Hunter 28689 Support Question

Find answers below for this question about Hunter 28689.
Need a Hunter 28689 manual? We have 3 online manuals for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-152344 on June 26th, 2015

Installed It And Fan Works But The Lights Don't.

I connected the wires the way I thought they are supposed to go. The lights don't work and I'm certain the bulbs are good. The fan works fine

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TechSupport101 on June 27th, 2015 12:07 AM

TechSupport101

Member since:
May 24th, 2013

Points: 12,171,305

100
points

Confirm this with the setup section of the manuals here just to be sure you did not miss a wire or two. Otherwise, the unit may be defect requiring to be returned to the retailer.

www.satechhelp.co.za

Related Hunter 28689 Manual Pages

Owner's Manual - Page 1

For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Model No. Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 42443-01 20100920 ©2010 Hunter Fan Co.

Owner's Manual - Page 2

... the Ceiling Plate 7 3 • Assembling and Hanging the Fan . . . . 8 4 • Wiring the Fan 9 5 • Installing the Canopy and Canopy Trim Ring 10 6 • Assembling the Blades 11 7 • Completing Your Installation With or Without a Bowl Light Fixture 12 8 • Operating and Cleaning Your Ceiling Fan 16 9 • Troubleshooting 17 Welcome Your new Hunter® ceiling...

Owner's Manual - Page 3

...of the fan. 30" From Wall or Nearest Obstruction 7' Minimum Blades to Section 2 • Installing the Ceiling ...fan. Wiring • e electrical cable is suitable, skip ahead to Floor 8' Minimum Ceiling Height Checklist for Existing Fan Site If you cannot check off every item, prepare a new fan site as specified by an approved connector. • Six inches of the fan and light...

Owner's Manual - Page 4

... or plaster of 1/16" into the ceiling. You have now successfully prepared your ceiling fan, go to install the support brace and outlet box. If you to recess the outlet box a minimum of the fan and light kit. Step 5 CAUTION: All wiring must be in accordance with the joist or support brace. 4-3. If the joist...

Owner's Manual - Page 5

... accessories, follow the instructions included with each product. You can purchase Hunter extension downrods. To install and use only the hardware supplied. 5 42443-01 • 09/20/10 • Hunter Fan Company For quiet and optimum performance of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting.

Owner's Manual - Page 6

Check for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. Installing Multiple Fans? Gathering the Tools You will need help installing the fan, your fan to avoid damage to the fan parts. If you are missing or damaged, contact your Hunter dealer or call Hunter Technical Support Department at 888-830-1326. (In Canada...

Owner's Manual - Page 7

...are pointing toward the ceiling peak. 2-2. Do not over tighten. Thread the supply wires from each of the ceiling plate. 2-5. The pilot holes should be 9/64"... are pointing toward the ceiling peak. 2 • Installing the Ceiling Plate CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off position, securely fasten...

Owner's Manual - Page 8

... must tilt the canopy to install the pipe and ball assembly. Loosen the square head setscrew on the pipe will still be visible; Once assembled, do not remove the downrod. Align the holes in the ball. 3-3. Unbundle the wires from unscrewing. 3 • Assembling and Hanging the Fan WARNING: Fan may fall if not assembled...

Owner's Manual - Page 9

...(ungrounded) from the ceiling to the black (ungrounded) and the black/white wire (ungrounded) from the fan. 4-4. Before attempting installation, make sure the power is still off. 4-2. Spread the wires apart, with wiring, use a qualified electrician. Connect the white wire (grounded) from the ceiling to the green ground wire (grounding) from the ceiling plate and the green ground...

Owner's Manual - Page 10

... are properly aligned, securely tighten all the holes are still in the canopy must be aligned. 5-2. 5 • Installing the Canopy and Canopy Trim Ring WARNING: Failure to complete the following steps. Swing the fan up to fall. Verify that must remain engaged while swinging the canopy for the following steps could cause...

Owner's Manual - Page 11

...to prevent scratching the to the blade iron and the flared tops of the blade iron posts are installed. use a furniture polish or any Once they will Post feel the blade lock into place and ...damp lint free cloth 1. blades. 11 42443-01 • 09/20/10 • Hunter Fan Company Make sure the blade is locked into place. 6-3. Step 6-2 WRONG Step 6-3b WRONG Step 6-3c Step 6-1...

Owner's Manual - Page 12

... cap and plug button. The steps below direct you whether or not you the option of another light kit will result in the switch housing and light fixture falling. This feature gives you are installing a light fixture. Use of installing the fan with this fan model. WARNING: Use only the light fixture supplied with OR without the included...

Owner's Manual - Page 13

... WARNING: Use only the light fixture supplied with the screws on the upper switch housing. Note: Both plug connectors are properly aligned before connecting them. Make sure the connectors are polarized and will only fit together one way. Twist the lower switch housing assembly clockwise to the fan, partially install two housing assembly screws into...

Owner's Manual - Page 14

... the hole in the side of the extra chain.) For Light Bulbs Metal Disc Metal Rod Breakaway Connector Glass Bowl Cover Plate Finial 14 42443-01 • 09/20/10 • Hunter Fan Company 7 • Completing Your Installation With or Without a Bowl Light Fixture (Continued) Installing the Glass Bowl 7-6. Attach the extra pull chains (included) to...

Owner's Manual - Page 15

7 • Completing Your Installation With or Without a Bowl Light Fixture (Continued) Uninstalling the Light Fixture 7-12. Install the dummy terminals (included in the sack parts) on the two disconnected wires in the center of the lower switch housing. Install the switch housing cap and plug button to the lower switch housing. To uninstall the light fixture, first disconnect...

Owner's Manual - Page 16

... and let it come to cool the room with Hunter's Dust Armor protection, making the blades less likely to the light fixture. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in sequence: High, Medium, Low, and Off. • Pull the chain slowly to change settings. • Release ...

Owner's Manual - Page 17

Pull the pull chain to the wiring the fan section. 3. Problem: Excessive wobbling 1. Loosen canopy, check all the blades. Push motor...After thoroughly verifying the blades are securely attached to the blade irons according to balance the fan. 3. Turn power on . 6. If so, replace all connections according to ensure it is cracked. If you need parts or service assistance, please call ...

Parts Guide - Page 1

... Assembly Hardware Kit Wire Connector Screw, Switch Housing Assembly Pull Chain Pendant Pull Chain Pendant Pull Chain Pull Chain Bottom Cap Finial Globe/Shade Dummy Terminal, Male Dummy Terminal, Female Cap, Switch Housing Plug Button CFL Bulb Balancing Kit Model # Asm. Dwg. # 28688 G1007-01 28689 G1007-02 28690 G1007-03 Finish Brushed...

Installation Guide - Page 1

... the outlet box a minimum of 1/16" into the ceiling. 3-2. Fan Support System Fan Support System Suitable Existing Fan Site Wiring Outlet Box Hunter Fan Company Step 2 Cut the Ceiling Hole 2-1. If NOT, install a support brace as described on this page. Step 5 Step 5 Prepare the Wiring 5-1. Make certain the wiring meets all national and local standards and ANSI/ NFPA 70...