Hoover UH60010 Support Question
Hoover UH60010 Support Question
Find answers below for this question about Hoover UH60010 - WindTunnel Bagless Self Propelled Upright Vacuum.Need a Hoover UH60010 manual? We have 1 online manual for this item!
Question posted by KandyFalvey on August 14th, 2012
Hoover Windtunnel Uh60010 Broken Valve Arm Rear-how To Disassemble Vacuum
Need to know how to get top plastic cover of vacuum to get access to this part. Took out all the screws but it is still connected. Or Can it be done without removing the motor?
Need to know how to get access to this part. Can I get the top plastic cover off or do I have to take the motor out to get to it.I have removed all visible screws but it is still connected. Any help is greatly appreciated.
Current Answers
Related Hoover UH60010 Manual Pages
Product Manual - Page 1
Self-Propelled WindTunnel™ Bagless with Powered Hand Tool by HOOVER
®
This product was designed for easy Assembly (See page 3)
www.hoover.com
Product Manual - Page 2
... cord. For your HOOVER product. Do not allow vacuum cleaner to be required...4 Cleaning Tools 6-7 Embedded Dirt FINDERTM Feature .5 Upright Cleaner 4-6 Self-Propel Feature 4
Important Safeguards 2 Maintenance
Authorized Service 13 ...Hoover Company; Owner's Manual
ENGLISH § pp.1-15 ESPAÑOL § pág. 17-26 FRANÇAIS § p. 27-36
Review this appliance before connecting...
Product Manual - Page 3
...
1-2
D
A
Looking at www.hoover.com to speak with owner's manual)...remove the switch lock until assembly is missing. Push 4 screws into electrical outlet. Using a Phillips screw driver, tighten screws securely.
Assembling cleaner
This cleaner was inspected and packaged carefully before being shipped from self-propel button. Carton contents
1-1
Accessories
C
D
A
B
Remove...
Product Manual - Page 4
... not change the plug in upright position, tilt cleaner back on bottom of cleaner. For increased control in a polarized outlet only one blade is intended for
(inside dirt cup)
can be rotated right or
14. Self-propel button
17. ON-OFF switch
18. Tool cover
19. Cord hooks: wrap
12. rear wand.
*available on 26...
Product Manual - Page 5
..."Hi" position.
•At other times, the red light may seldom come on , you know that the 'Dirt FINDER' feature is being removed by using cleaning tools; upright for storage and when using the carrying handle on the back of dirt is ready the red light...setting: for all types of dirt which the system may then begin. Cleaning may not detect, or that may need more cleaning attention.
Product Manual - Page 6
... to tighten or loosen the connection.
6
Attach wand and tools
Attach any tool or wand to the hose (F) by pushing it at bottom of the nozzle to remove dirt in moving the cleaner from bottom to the edge of rug and move cleaner...and for stair cleaning.
Cleaning tools
When using cleaning tools, cleaner handle must be in the upright position to another. To use only forward strokes.
Product Manual - Page 7
... and pull straight out to remove from electrical outlet. How to attach tool cover
The tool cover is designed with a "break... align hinges of cover with the dusting brush and/or extension wand. Rinse and air dry before disconnecting and connecting hose. When to...loss of stairs and hard-to -reach places. L. How to your vacuum cleaner, follow the instructions below.
2-18
M N
Turn cleaner OFF ...
Product Manual - Page 8
...it to empty dirt cup" should sufficiently remove dust and fine particles from the HEPA cartridge...removed for additional cleaning.
3-7
J
K
3-8
Grasp end of HEPA cartridge filter and pull it is not necessary to remove... cleaner cavity. 3-3
3-4
3-5
F
H
G
I
To remove loose dirt from the HEPA filter, turn knob (G) on ...(H) to clean filter assembly
Remove dirt cup and open dirt cup lid...
Product Manual - Page 9
... 912 bulb, Hoover part No. 27313101.
3-15
3-16
Slide filter assembly down all the way.
Press door back into place. Remove debris as shown and lift off lens. Remove filter (N) and...filter area. To reattach, align hinges (O) of cover with the two screws. Continued
9 Reposition bottom plate (Fig. 3-22).
3-17
Removing lens
Disconnect cleaner from electrical outlet. Replacing lens
...
Product Manual - Page 10
... motor shaft (D).
3-21
C Positioning front of belt over .
the other end of belt Place other is turned over.
3-18
A Removing bottom plate Place handle in good condition.
To check the flat belt, remove bottom plate as shown with your cleaner. What to buy
To assure effective operation, use only genuine HOOVER belts with a Phillips screw...
Product Manual - Page 11
...Hoover belt part no. 38528034 (belt package part no. 40201200).
Belt may fit loosely when properly installed. Press the latches on either side of belt over pulley (C). Unscrew the two Phillips screws and remove...To remove V-belt, slide back of tool and remove bottom plate (A).
2. Replace with lettering on side of brush roll (H) into place. However, if V-belt is cracked, gouged or broken,...
Product Manual - Page 12
...screws.
3-33
A
Powered hand tool
Belt replacement
The powered hand tool belt is not normally replaced. The belt can be replaced.
3-34
8. Replacing belt
When replacing belt, ask for HOOVER part No. 38528037. 1. Remove...D
3-31
3-32
B
C
C
E
3.
However, if the belt is cracked, gouged or broken, replace it is in tool housing and snap into slots on front of bottom plate into place...
Product Manual - Page 13
...Service
To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot).
The majority of this happens, proceed as follows:
1. Remove bottom plate as shown. The addition of the motor.
only). Always...
Product Manual - Page 14
... OFF and disconnect from electrical outlet. 1. Do not remove any blockage. C.
Replace belt turbine, brush roll, belt guard and bottom plate.
Clearing blockages
Disconnect cleaner from hose. Problem: Cleaner won 't self-propel
Possible cause
Possible solution • Flat belt broken or worn • Replace belt. • Self-propel button in OFF position • Move brush roll...
Product Manual - Page 15
... for warranty service, transportation will be paid one full year from date of purchase. This warranty applies when the appliance is needed, or if there are covered by presenting the appliance to a Hoover Factory Service Center for a period of one way. This warranty does not apply if the appliance is used in a commercial...
Product Manual - Page 16
HOOVER y
son marcas registradas
HOOVER et
sont des marques déposées
HOOVER and
are registered trademarks
R1 10-02 U6625/30-/55-900, U6630-960
Printed in Mexico
56511-B64
Similar Questions
How Do I Get My Hoover Windtunnel Uh60010 Apart
(Posted by wchaTEJA 9 years ago)
Hoover Windtunnel T-series Rewind Upright Vacuum Bagless Uh70120 Motor Wont
work
work
(Posted by rexadria 9 years ago)
Hoover Windtunnel Anniversary Upright Vacuum, Self-propelled, Bagged, U6485900
won't shut off
won't shut off
(Posted by patciam 9 years ago)
Tool Hose Poor Suction Uh60010
H=Brand new Hoover UH60010. The hose for the tools has very little suction and will not spin the tub...
H=Brand new Hoover UH60010. The hose for the tools has very little suction and will not spin the tub...
(Posted by Reedsid 12 years ago)