Hoover U8315960 Support Question
Hoover U8315960 Support Question
Find answers below for this question about Hoover U8315960 - WindTunnel 2.Need a Hoover U8315960 manual? We have 1 online manual for this item!
Question posted by Anonymous-62725 on June 14th, 2012
How Do I Change The Beater Belt On U8315-960?
The person who posted this question about this Hoover product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hoover U8315960 Manual Pages
Manual - Page 3
...cord or pull cord around sharp edges or corners. Change bag frequently when picking up very fine materials such as...Agitator brush roll belt . . . . . 14 Replacing powered pet hair cleaning tool brush roll . 15-16 Replacing powered pet hair cleaning tool belt 16 Thermal ... Center or Authorized Hoover Warranty Service Dealer. • Use vacuum cleaner only for its intended use . • Do not...
Manual - Page 6
... the back of the cleaner.
24
This cleaner is intended for storage. If the plug does not fit fully in any way.
06 Do not change the plug in the outlet, reverse the plug. Cleaner description
Features
8
Use the following to install the proper outlet. Edge groomers 9. Surface Selector (some models...
Manual - Page 8
... cleaner back on rear wheels and push forward. low for storage, hold plug until it changes to clean.
08 When the dirty light is rewound.
16 To help keep the cord out of the
way while vacuuming, position cord in cord clip (D), located on the back of the Tag Along™ grip...
Manual - Page 11
... bottom of this manual. What to time. HOOVER® bags can fill the bag quickly while vacuuming.
B
C
33
The bag door is only partially full of your cleaner will ensure continued cleaning ... in place.
34
Remove filter bag by Hoover to change filter bag, grasp top of this nature, change filter bag often.
Your cleaner will be purchased from leaving the bag.
To...
Manual - Page 13
... a new agitator brush roll, ask for HOOVER part no. 48414140. Slide the belt onto the agitator brush roll, positioning the belt in
one hand. To maintain cleaning effectiveness, replace agitator brush roll if brushes do... so bottom side is up on the agitator brush roll.
(Cont'd) ¡ 13 Do not allow the belt to fall back into the cavity on to HARD FLOOR. C E
D
42 Pull up . Turn cleaner OFF...
Manual - Page 14
... roll shield.
46 Reposition bottom plate and five
screws. Remove agitator brush roll
including end plates (C) and discard. 4. Unscrew the two Phillips screws and remove belt guard
(B).
47 1. gular slot (F) on
the powered pet hair cleaning tool
are worn, the agitator brush roll should not need replacement. F
B
45
Grasp agitator brush...
Manual - Page 15
... and agitator brush roll as described in guard. Replace with new belt.
(Cont'd) ¡ 15 A
53 8. Belt replacement
Inspect the belt
The powered pet hair cleaning tool belt is cracked, gouged or broken, it rotates freely. Replace belt
When replacing belt, ask for HOOVER part No. 38528037. 1.
Pivot bottom plate down ,
slide end plates (C) of agitator...
Manual - Page 16
... blockage in tool housing and snap into grooves (H) in the system. Replace agitator brush roll, belt guard, and bottom plate as hair, strings, etc., the cleaner will stop running . If this...continuing with each step until the blockage is unplugged and the motor cools for dirt accumulation.
3. Change bag if needed (Figs. 32 through 53.
Check dirt tube opening (A) and remove. Remove ...
Manual - Page 17
Remove bottom plate, belt guard and turbine as described in and turn ON. Remove wand from wand.
5.
Remove hose from cleaner. Clear blockage.
59 6.... tool
A
58 4. Check for blockage. If there is suction, continue with step 6. nect from electrical outlet.
7. Clear blockage.
60 1. Replace belt turbine, agitator brush roll, belt guard and bottom plate.
(Cont'd) ¡ 17
Manual - Page 18
... back of the cleaner. The addition of authorized service outlet locations
(U.S. If further assistance is equipped with this cleaner OR Checking the Yellow Pages under "Vacuum Cleaners - our Consumer Response Center (8 AM to Hoover in delay. Friday)
Please do not add lubricant to any assistance or need any bearings. Therefore, do...
Manual - Page 19
... the Surface Selector control dial. What's the problem?
Select a suitable carpet mode setting. Disconnect cleaner from electrical outlet.
Incorrect carpet height setting.
Blockage in system. Change filter bag.
Cleaning tools won't pick up ".
19 What's the cause? What's the solution? Filter bag full. Blockage in system...
Similar Questions
How To Replace Agitator Belt On Hoover Windtunnel 2
(Posted by drajmjc0453 9 years ago)
How To Change The Belts On A Hoover Windtunnel Pet Plus
(Posted by jkozaMarc 9 years ago)
How To Change The Belts On A Mach Cyclonic Vacuum Uh70040w
(Posted by teknocfre 10 years ago)
How To Change Belt On Hoover Windtunnel 2
(Posted by PauAn 10 years ago)
Hoover Windtunnel Vacuum Won't Turn On
(Posted by Marydgo 10 years ago)