Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by cdavies on May 9th, 2011
I Changed My Batteries With Fresh New Ones. Now My Backlit Display Is Not Visibl
Is there a reset button?
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type. Install the batteries. Install the thermostat. Set the system. Call 1-800-468-1502.
1 Do you...
Owner's Manual - Page 3
... the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2
This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type...
Owner's Manual - Page 4
... not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Do not remove wallplate yet. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
....
Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your new thermostat.
RTH2310 Programmable Thermostat
Identify Wires
3. If any wires are not attached to your old...
Owner's Manual - Page 6
Insert plastic anchors. Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5. Labels don't match?
Owner's Manual - Page 9
HE Place the jumper to the G terminal. J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8
RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace.
Owner's Manual - Page 10
... be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. Observe the
polarity. 3) Reinstall the battery cover. It is installed on the wall. After the batteries are holding the thermostat. Afterwards, the screen displays the actual temperature. By default, the setpoint is 70 °F (21 °...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default ....
2 See page 3 of Operating Manual.
3 Use the system switch to the next function, briefly press both and buttons simultaneously.
3) To change the setting, press the or...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
Nearly Blank Screen
My Honeywell screen is fading, we've changed batteries still nearly blank screen, think the model is...
My Honeywell screen is fading, we've changed batteries still nearly blank screen, think the model is...
(Posted by Karenanderson1234 10 years ago)
How To Set Clock To 12 Hours
Somehow system stopped while we were away. Now the one (out of three) thermostat went to a 24 hrs cl...
Somehow system stopped while we were away. Now the one (out of three) thermostat went to a 24 hrs cl...
(Posted by skiqueen58 11 years ago)
Display Screen Is Blank After Changing Batteries
The display screen showed LO which we took to mean the batteries were low even though the manual doe...
The display screen showed LO which we took to mean the batteries were low even though the manual doe...
(Posted by bhugg137 12 years ago)