Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by pauljohnson on September 17th, 2011
How To Stop Thermostat Chirping
My thermostat won't stop chirping. I replaced the batteries. I don't know the model but it is 3 yrs old. I read where you would see a music symbol, but this model doesn't have that
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
...step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the ...furnace type. Install the batteries. Install the thermostat. Set the system. Quick Installation Guide
Installation is Easy
Your new thermostat has been designed for fast and ...
Owner's Manual - Page 3
RTH2310 Programmable Thermostat
Identify System Type
1.
This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502. This thermostat is compatible with the...
Owner's Manual - Page 4
... remove wallplate yet. Contact your old thermostat in the trash if it contains mercury in a sealed tube. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3
Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with...
Owner's Manual - Page 5
...wires around a pencil to identify wires. If any wires are not attached to your new thermostat. Do not use non-connected wires. Do not use C or C1 wires
Identify and... and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your old thermostat or are labeled.
RTH2310 Programmable Thermostat
Identify Wires...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors.
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 If a wire does not match any excess wire back into the wall opening.
Labels don't match...
Owner's Manual - Page 9
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8
HE Place the jumper to the G terminal.
Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
..., the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. The thermostat will hear a clicking
sound. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown. It is 70 °F (21 °C).
9
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
Thermostat Will Not Trigger Heat After Replacing Batteries
My thermostat batteries died while away. I replaced them and it appears to be working but no matter ...
My thermostat batteries died while away. I replaced them and it appears to be working but no matter ...
(Posted by rfeldman5 7 years ago)
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
Installing The Thermostat
i'm installing the Thermostat and for the RH terminal I have 3 wires and they are C L O witch one do...
i'm installing the Thermostat and for the RH terminal I have 3 wires and they are C L O witch one do...
(Posted by marthasbng40 12 years ago)
How To Replace Battery In Thermostat
my thermostat digitial display is blank and might need new battery how to replace battery
my thermostat digitial display is blank and might need new battery how to replace battery
(Posted by wwebjenks 12 years ago)