Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by marthasbng40 on February 7th, 2012
Installing The Thermostat
i'm installing the Thermostat and for the RH terminal I have 3 wires and they are C L O witch one do i put in the slot?
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... the simple step-by-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type. Install the batteries. Install the thermostat. Set the system.
Owner's Manual - Page 3
... systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2
RTH2310 Programmable Thermostat
Identify System Type
1. This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of...
Owner's Manual - Page 4
... your local waste management authority for instructions regarding recycling and proper disposal.
3 Contact your old thermostat in the trash if it contains mercury in a sealed tube.
Do not remove wallplate yet. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
..., so it cannot touch and short other wires.
Wrap the bare metal end of each wire. IGNORE WIRE COLORS: Use terminal screw designations to prevent them from falling though the wall opening.
4
RTH2310 Programmable Thermostat
Identify Wires
3. Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be...
Owner's Manual - Page 6
Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
... wire back into the wall opening. Labels don't match?
Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 RTH2310 Programmable Thermostat
Connect Wires (typical wiring...
Owner's Manual - Page 8
Do not use C, X or B. Wrap bare end of wire with electrical tape. Quick Installation Guide
Connect Wires (less common wiring)
If a labeled wire does not match any terminal designation, see previous page).
7
If wires are connected to both Rh and Rc terminals, remove jumper (see diagram below.
Owner's Manual - Page 9
Set the Jumper J2, on the back of the thermostat, if you have an electric furnace.
8 HE Place the jumper to this factory-set position if you have connected a wire to the G terminal. J2 jumper
HG Leave the jumper in this position if you have a gas or oil furnace.
RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
... setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. After the batteries are holding the thermostat. You will display the ambient temperature once it is installed on the wall. Observe the
polarity. 3) Reinstall the battery cover. The...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
Quick Installation Guide
System Setup
9.
1) Press both and buttons simultaneously.
3) To change the setting, press the or button. DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How To Hook Up A Honeywell Thermostat Th3110d1008 With 2 Wires
(Posted by niciscok 9 years ago)
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
Honeywell Rth2310 Installation
How do I adjust the temperature difference between call for heat and shut off
How do I adjust the temperature difference between call for heat and shut off
(Posted by Poppyhas4 10 years ago)