Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by stanmann on July 3rd, 2011
Rth2310 User Manual
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... are here to help. Just follow the simple step-by-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type...
Owner's Manual - Page 3
... the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type...
Owner's Manual - Page 4
MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Do not remove wallplate yet.
Contact your old thermostat in the trash if it contains mercury in a sealed tube. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old...
Owner's Manual - Page 5
...wires are attached to a terminal marked C or C1, they will not be connected to your old thermostat or are labeled. Wrap the wires around a pencil to identify wires. IGNORE WIRE COLORS: Use terminal...4
If any wires are not attached to your new thermostat.
Wrap the bare metal end of each wire. Do not use non-connected wires. RTH2310 Programmable Thermostat
Identify Wires
3.
Owner's Manual - Page 6
Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5
Owner's Manual - Page 7
RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5. If a wire does not match any excess wire back into the wall opening.
Remove jumper if you have both R and... the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 Labels don't match?
Owner's Manual - Page 9
HE Place the jumper to the G terminal.
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace.
RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
..., the setpoint is installed on the wall. It is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. The thermostat will hear a clicking
sound. After the batteries are holding the...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are shown in bold and underlined.
2 See page 3 of Operating Manual.
3 Use the system switch to the next function, briefly press both and buttons simultaneously for gas or oil), 6=10 min (electric).
5 The corresponding cooling cycle...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
How To Wire Rth2310 To An Oil Fired Boiler?
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
(Posted by Grayai 12 years ago)