Honeywell 6160RF Support Question
Honeywell 6160RF Support Question
Find answers below for this question about Honeywell 6160RF.Need a Honeywell 6160RF manual? We have 2 online manuals for this item!
Question posted by dllski on August 5th, 2012
Honeywell 6160rf Keypad Repair Parts?
The RF keypad (after entering the security code to turn off the previously secured alarm system) suddenly stopped communicating with all remote sensors.
Current Answers
Related Honeywell 6160RF Manual Pages
User Guide - Page 1
...CODE
0
! The table describes the error messages and the corrective actions. Contact your installer for easy identification. The following table cause the keypad to be armed (no zone faults are continuously backlit for ease in any mode.
The panic alarms... 6160RF
Keypad/Transceiver
KEYPAD DISPLAYS AND LEDS
The 6160RF has the following functions: • Produces warning sounds during alarm...
User Guide - Page 2
...protection against such interference in Part 15 of FCC Rules, which can be determined by turning the equipment off and ....
‡K0904V1DŠ
K0904V1 2/06 Rev. www.honeywell.com/security CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested...conforme à la norme NMB-003 du Canada. FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modifications...
Setup Guide - Page 1
Push the two case release snaps at the bottom of the keypad with high-security (encryption) capability (e.g.; 5804E). • Provides a nominal range of 200 feet' for RF transmitters (some transmitters have a shorter range). • Supports RF jam detection when the receiver is being used on the 6160RF as 5804BD, 5804BDV and
5828/5828V. Insert the screwdriver...
Setup Guide - Page 2
... Yellow
5.
Notes: * On VISTA-40 panels and above the 6160RF's partition assignment must match the partition assigned to the control panel's installation instructions for a few seconds within 60 seconds after applying power. (Keypad Address) Enter the two-digit keypad address.
Enable the receiver if RF transmitters or wireless keypads are programmed into place securely.
6.
Setup Guide - Page 3
... for 3 seconds. Exit out of 8 devices. The current keypad address will only operate if the 6160RF is enrolled the 6160RF will support a maximum of Programming Mode.
2. Note: Refer to delete the stored high security device. Press the [✻] key to continue.
(Enable High Security Mode) Enter [1] to Application Guidelines section when selecting a House ID.
ACTIVATING...
Setup Guide - Page 4
... service. LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165 Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with Seller's specifications or proves defective in materials or workmanship under this Limited Warranty is not communicating to correct the interference by turning the equipment off...
Similar Questions
Beeping Sound After Power Outage
I have this model and when there is a power surge and the power comes back, the keypad beeps in inte...
I have this model and when there is a power surge and the power comes back, the keypad beeps in inte...
(Posted by gardnerwilliam 4 years ago)
Xl4600sm Beeping
I have a keypad that continually beeps. We enter the code and it stops for 15 minutes and then beeps...
I have a keypad that continually beeps. We enter the code and it stops for 15 minutes and then beeps...
(Posted by JoeSpore 6 years ago)
I Need A User Manual For Honeywell Home Security 6149ex Keypad
(Posted by Willoughby 9 years ago)
How To Shut Off The Beep Sound When The Door Opens On My Fbii Xl Security Alarm
How do you shut off the beep sound that occurs when the door open opens but the alarm is no engaged ...
How do you shut off the beep sound that occurs when the door open opens but the alarm is no engaged ...
(Posted by sacsmom7 9 years ago)