Homelite UT10589 Support Question
Homelite UT10589 Support Question
Find answers below for this question about Homelite UT10589.Need a Homelite UT10589 manual? We have 4 online manuals for this item!
Question posted by Tyronepearce on December 22nd, 2016
New Bump Feed Spool And Knob.
I am unable too get the new bump feed spool off the machine
Current Answers
Answer #1: Posted by techyagent on December 23rd, 2016 8:40 AM
techyagent
Member since:
June 17th, 2014 Points: 4,799,790
Member since:
June 17th, 2014 Points: 4,799,790
you can check this video tutorial
Quick video showing possible cause and fix of a bump feed not working on your weedeater, this is just one possibility it could be a number of things causing your problem, but this is a good place to start.
Thanks
Techygirl
Related Homelite UT10589 Manual Pages
User Manual - Page 12
... eyes, wash them immediately with skin. Move at least 30 ft. from the use any leaks, correct the problem before starting the engine. Failure to a machine with a running or hot engine. A leaking fuel cap is a fire hazard and must be required. Failure to Refueling in contact with clean water. n Do not...
User Manual - Page 26
... the bar studs are sharp and may need to possible serious injury. n Remove the bar mounting nuts using the combination wrench provided. n Lay out the new saw . These components are in the direction of the bar. The cutters should face in the long slot of the bar. n Place the chain drive...
User Manual - Page 28
... in .
Always wear protective gloves when performing maintenance on the drive links hang out of a correctly tensioned warm chain will hang approximately 0.050 in .
NOTE: New chains tend to avoid possible injury.
NOTE: During normal saw chain is running. check the chain tension frequently and tension as a guide to help determine...
User Manual - Page 31
...; Results from using a file with flat file when adjusting depth gauges. depth gauge jointer.
English
Fig. 57 feathered edge dulls quickly. n HOOK - Needs too much feed
TOP PLATE FILING ANGLE 30°
pressure;
n Maintain the depth gauge at a clearance of 0.025 in the file holder. Be careful not to damage adjoining...
User Manual - Page 33
... the right hand side of the cylinder cover past the handle.
NOTE: An alternate method is correctly replaced before further operation.
n Tighten the screw with a new filter after every 25 hours of a turn using the following method.
A torque within this may cause serious damage to the chain saw dust and dirt...
User Manual - Page 36
... gap. The spark arrestor must be in different locations depending on the model purchased. MAINTENANCE
CHECKING THE FUEL FILTER
See Figure 69.
n Hand thread the new spark plug, turning it counter- Cross-threading will seriously damage the cylinder. CLEANING THE EXHAUST PORT, MUFFLER, AND SPARK ARRESTOR
NOTE: Depending on the type...
User Manual - Page 37
... feet. Page 37 -
When storing 1 month or longer: n Drain all bar and chain lubricant from the product. n Drain all fuel from corrosive agents such as garden chemicals and de-icing salts. HIGH ALTITUDE ENGINE OPERATION
Please have an authorized service center restore high altitude modified engines to purge fuel from carburetor...
User Manual - Page 38
Refer to 20 times. Pull starter three times with a new spark plug.
Clean air filter.
BAR AND CHAIN COMBINATIONS
Chain specifications: 3/8 in this manual. pitch, .05 in completely) and pull starter cord 15 to Spark ...
User Manual - Page 40
... to the original retail purchaser only and commences on to our website at Homelite's, discretion, any defective product free of charge within the warranty period. Bump Knobs, Outer Spools, Cutting Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower Fans, Blower and Vacuum Tubes, Vacuum...
User Manual - Page 41
..., catalytic converters, fuel tanks, valves, filters, clamps, connectors, and other states, new 2011 and later model year non-road engines must warrant the emission control system on...Homelite Consumer Products, Inc., is delivered to other emission-related assemblies. In California, new equipment that is warranted for damages to an ultimate purchaser.
(b) General Emissions Warranty Coverage...
Getting Started Guide - Page 1
...
Above 50ºF - Pull STARTER grip and rope until
For any questions about operating or maintaining your new tool on-line. IMPORTANT: It is normal for reading the operator's manual.To reduce the risk of ...and chain lubricant is coming from the clutch cover area and is NOT an indication of your new chain saw.
WARNING: This Engine Starting Procedure is not a substitute for chain saws to ...
Similar Questions
How To I Remove The Spool Head From The Shaft?
I want to replace the spool head with a plastic blade unit. How does the head come off?
I want to replace the spool head with a plastic blade unit. How does the head come off?
(Posted by Bsackett 7 years ago)
Won't Keep Running
I tried starting my chainsaw te first time since last Spring. New gas, regapped plug. I had left gas...
I tried starting my chainsaw te first time since last Spring. New gas, regapped plug. I had left gas...
(Posted by dlong3211 9 years ago)
How To Load Spool On A Model Ut33600
I have homelite UT33600 dual feed edger and I'm trying to fine an instruction video for this
I have homelite UT33600 dual feed edger and I'm trying to fine an instruction video for this
(Posted by jayman626 10 years ago)