Hitachi NV65AH Support Question
Hitachi NV65AH Support Question
Find answers below for this question about Hitachi NV65AH - Pneumatic Coil Siding Nailer Wire/Plastic Collation.Need a Hitachi NV65AH manual? We have 1 online manual for this item!
Question posted by kawgpzrider on September 24th, 2014
Where Is Serial Number Located?
where is serial number located?
Current Answers
Related Hitachi NV65AH Manual Pages
Instruction Manual - Page 3
English
IMPORTANT INFORMATION
Read and understand tool labels and all of Nailers are caused by the failure to observe basic safety rules or precautions. ...avoided by recognizing a potentially hazardous situation before operating or maintaining this Manual. Never use this Nailer for applications other than those specified in this Manual and in the sections which , if not avoided, could result...
Instruction Manual - Page 4
... use of American National Standards Institute, ANSI Z87.1 and provide protection against flying particles both from the front and side. NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA. Never point the Nailer at yourself toward yourself or others in work area. 2. Never engage in work area wear safety glasses, too. KEEP...
Instruction Manual - Page 5
... LIVE WIRES. STORE NAILER PROPERLY. Make sure the push lever operates properly. (The push lever may be driven through the wall and hit a person on the workpiece with or remove the push lever, otherwise the push lever becomes inoperable.
15. and 3) keep the push lever away from the point of unnecessary tools, debris...
Instruction Manual - Page 6
... COIL NAILER
WARNING
1. WHEN YOU DETACH AND ATTACH A HOSE CAP, DISCONNECT AIR HOSE FROM NAILER. Maintain Nailers properly.
6.
The Nailer should never be driven away from the Nailer.... Keep the Nailer clean and lubricated for better and safer performance.
33.
Keep Nailers in personal injury.
4. Continued
27. HANDLE NAILER CORRECTLY. Because of wire collating fasteners can ...
Instruction Manual - Page 7
Some illustrations in the safe operation of the Nailer. NAME OF PARTS
Exhaust Cover Piston
Piston O-Ring
Driver Blade
Top Cover
Trigger Body
Cap Air Plug (Sold separately)
© ©
Nose
A
A
Adjuster
Knob Nail ... information contained in this Manual is designed to assist you in this Manual may show details or attachments that differ from those on your own Nailer.
Instruction Manual - Page 8
...the Table below can be driven with this Nailer.
Wire-collated coil nails
Min.
.209" (5.3 mm)
Max.
.252" (6.4 mm)
1-1/2" (38 mm) 2-1/2" (64 mm)
Sheet-collated coil nails
.090" (2.3 mm)
.099" ... 5 - 1/16" (266 mm × 300 mm × 128 mm)
4.6 lbs (2.1 kg)
200 - 300 nails (1 coil)
.049 ft3/cycle at 100 psi (1.4 ltr/cycle at 6.9 bar) (1.4 ltr/cycle at 7 kgf/cm2)
3/8 NPT Thread
NAIL...
Instruction Manual - Page 9
...Nailer.
1. These units should always be installed as a power source for this Nailer must remove all pressure from the Nailer when disconnected. Regulator .... Lubricator ... Use Hitachi pneumatic tool lubricant. Dust Cap
WARNING
ⅷ Never connect Nailer to this Nailer... of lubricant is higher.
4. Nailer Side
Regulator Compressor Side
Lubricator
Filter
3. Air hose
Air hose...
Instruction Manual - Page 10
... Amount of air required =number of Hitachi pneumatic tool lubricant into the air plug on the Nailer twice a day.
CAUTION
ⅷ Do not free-fire the Nailer at 100 psi driving 30 nails per Nailer × air consumption at...side shields which conforms to ANSI Z87.1 specifications. LUBRICATION
It is important that is already cold, bring it in work , test the Nailer by using the Nailer...
Instruction Manual - Page 11
... . 3 Turn the nail holder 90 degrees clockwise until you may load nails in the Nailer. and 3) keep Nailer pointed downward.
(1) Press the magazine stopper and open the magazine
cover.
The nail will...the holder shaft in accordance with the length of the nails being used in the Nailer.
Ⅺ THE NAILER MUST NOT LEAK AIR. Magazine Stopper
Nail Holder
(2) Adjust the position of workpiece...
Instruction Manual - Page 12
...may be damaged.
(3) Place the nail coil in the magazine, adjust the nail ...tool at too steep of an angle; DANGER
ⅷ Operators and others in work area MUST wear safety glasses with side shields which conforms to disengage the nails with strong
force;
2) take Nailer... Guide Surface
NOTE: Be careful not to deform the collated wires and
not to ANSI Z87.1 specifications. English
Top of ...
Instruction Manual - Page 13
...nails because, if used as order part number 881973. You must first depress the push...pneumatic tool lubricant into thin boards or near corners and edges of operation to drive nails with the Nailer off the trigger except during a nail driving operation. Each depression of Operation". English
ⅷ Do not drive nails into the air plug on the opposite side.
ⅷ Never use Nailer...
Instruction Manual - Page 14
...push lever, attach the accessory nose cap to the push lever. 1 DISCONNECT AIR HOSE FROM NAILER. 2 Put the nose cap to protect the surface of nailing depth is required.
3 Stop ...when using the sheet collated nails.
2 If nails are in the following order. 1 DISCONNECT AIR HOSE FROM NAILER. NOTE: ⅷ The nose cap may reduce nailing depth due to the shallow side.
Adjustments are driven...
Instruction Manual - Page 15
...titled "SAFETY" (pages 4 - 6). Tap the rod with nippers.
Hammer
rod
2. Lubricate it with Hitachi pneumatic tool lubricant. Lubricate it with Hitachi pneumatic tool lubricant.
Nail
Slotted Screw Driver
5 Cut the deformed collated wire with a hammer. CAUTION
ⅷ Check that differ from Nailer when: 1) doing maintenance and inspection; Clearing a jam
Remove a jammed nail in the safe...
Instruction Manual - Page 16
....
4. Storing
⅜ When not in a cold weather environment. SERVICE AND REPAIRS
WARNING
ⅷ Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer.
ⅷ Use only parts supplied or recommended by Hitachi for an extended period, apply a thin coat of HITACHI. A new WARNING LABEL is available from normal...
Instruction Manual - Page 17
... Open manual petcock.
Driver blade worn? Intermittent feed.
Clean and lubricate. Clean magazine and feeder mechanism. Lubricate the Nailer after nailing. Keep the Nailer lubricated. Promote operator safety and efficient Nailer operation. Use Hitachi pneumatic tool lubricant.
Blow clean daily. Use larger air hose.
- 17 -
Open petcock on air compressor tank. CORRECTION Clear...
Similar Questions
How Do You Install A Sequential Fire Mechanism In A Hitachi Nv65ah Nailer
(Posted by Anonymous-170890 2 years ago)
Shoot One Nail Piston Shaft Will Not Go Back Up
(Posted by banubasdeo2 2 years ago)
I Have An Hitachi 45ae Coil Roofing Nailer That Has Begun To Leak Continuously
thru the exhaust port. Can you help me solve this problem. The equipment is less than a year old and...
thru the exhaust port. Can you help me solve this problem. The equipment is less than a year old and...
(Posted by jmartell83837 9 years ago)
Where Is Hitachi Serial Number Located C12rsh
(Posted by marsal 9 years ago)
Hitachi Av65ah Jams
With wire-collated stainless steel siding nails my nailer jams constantly (every 5-10 nails). What i...
With wire-collated stainless steel siding nails my nailer jams constantly (every 5-10 nails). What i...
(Posted by robdaves 11 years ago)