Home » Hitachi » Hard Drives » Hitachi HDS728080PLAT20

Hitachi HDS728080PLAT20 Support Question

Find answers below for this question about Hitachi HDS728080PLAT20 - Deskstar 80 GB Hard Drive.
Need a Hitachi HDS728080PLAT20 manual? We have 1 online manual for this item!

Hitachi Overview Questions Manuals Reviews Videos Research

Question posted by brendajsmit2 on July 19th, 2011

Jumper Settings

Hi I have a Hatachi Deskstar model HDS728080PLAT20 82.3GB & I need to use it as my master hard drive & need to know were to put the jumpers thanks regards Brenda

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by kcmjr on July 19th, 2011 4:10 PM

This answer was accepted by the poster of the original question.

kcmjr

Member since:
May 5th, 2011

Points: 4,254,255

1,140
points

In most cases the settings are marked on the circuit board or the connector if you look closely.

You can get the install guide from here: http://www.hitachigst.com/tech/techlib.nsf/techdocs/53FD870FC4F08F7786256E44007A149F/$file/D7K80_IG.pdf

On the back of the drive you will see two horizontal rows of pins. One row has one extra pin. Orient the drive so that row is on top when viewed from the rear. For master the 2 jumpers should be oriented vertically and on the jumper pins to the far right and far left when looking at the back of the drive.

See the guide for illustrations.

Licenses & Certifications: Microsoft, Cisco, VMware, Novell, FCC RF & Amateur Radio licensed.

Related Hitachi HDS728080PLAT20 Manual Pages

Specifications - Page 6

... settings 53 7.1.1 Jumper pin location 53 7.1.2 Jumper pin identification 53 7.1.3 Jumper pin assignment 54 7.1.4 Jumper positions 54 7.2 Environment 58 7.2.1 Temperature and humidity 58 7.2.2 Corrosion test 59 7.3 DC power requirements 59 7.3.1 Input voltage 59 7.3.2 Power supply current (typical 60 7.3.3 Power supply generated ripple at drive power connector 60 7.4 Reliability 61...

Specifications - Page 12

... and 40GB models 60 Table 46.Power supply generated ripple at drive power connector 60...82.Format Track command (50h 132 Table 83.Format Unit command (F7h 134 Table 84.Identify Device command (ECh 135 Table 85.Identify device information (Part 1 of 7 136 Table 86.Identify device information (Part 2 of 7 137 Table 87.Identify device information (Part 3 of 7 138 Deskstar 7K80 Hard Disk Drive...

Specifications - Page 15

... ATA function - Addendum.' HDS728040PLAT20 HDS728080PLAT20 41.1GB 82.3GB For Serial ATA function specification, please refer to change without notice. 1.2 References • Information Technology - AT Attachment with ATA interface and a rotational speed of force) G2/Hz (32 ft/sec)2 per Hertz Gb 1,000,000,000 bits GB 1,000,000,000 bytes Deskstar 7K80 Hard Disk Drive Specification 11

Specifications - Page 19

...Deskstar 7K80 Hard Disk Drive specification 15 2.0 General features of the drive • Formatted capacities of 40 GB and 80 GB...Command Overhead • Sector Buffer size of 2048 K (Upper 270 KB is used for firmware) • Ring buffer implementation • Write Cache • ...set support • World Wide Name Note: For serial ATA model, please refer "Serial ATA Function Specification -

Specifications - Page 25

... setting can be obtained by issuing an IDENTIFY DEVICE command. Deskstar 7K80 Hard Disk Drive Specification 21 Number of cylinders: For drives with capacities greater than 8.45 GB the Identify Device information word 01 limits the number of cylinders to 16, 383 per track 63 63 Number of Cylinders2 16,383 16,383 Number of sectors 80...

Specifications - Page 54

... Command Reg. For systems operating with Ultra DMA mode 3, 4, and 5, 80-conductor ATA cable assembly shall be used to select one of registers called a Task File. or DIOW- is shown...Deskstar 7K80 Hard Disk Drive Specification 50 These registers are accessible. Device control Reg. Status Reg. Table 39: I / O address map. and CS1-) and three address lines (DA0-2) are used...

Specifications - Page 58

...) Present Shipping Default Condition (DEVICE 0) Deskstar 7K80 Hard Disk Drive Specification 54 RSV GND GND GND RSV I GECA HFDB DS CS/SP GND RSV 7.1.4 Jumper positions 7.1.4.1 16 logical head default (normal use ) • 15 logical head default • 32 GB clip • Power up in standby Within each of these four jumper settings the pin assignment selects Device...

Specifications - Page 59

...drive address is 0 (Device 0). • When CSEL is open or at a high level, the drive address is 1 (Device 1). 2. Deskstar 7K80 Hard Disk Drive Specification 55 In the CSEL mode the drive... drive address is the Device 0 position. 7.1.4.2 15 logical head default The figure below shows the jumper positions used to select Device 0, Device 1, Cable Selection, or Device1 (Slave) Present setting ...

Specifications - Page 60

...A H F D B I GECA HFDB DEVICE 1 (Slave) Present Deskstar 7K80 Hard Disk Drive Specification 56 The CHS is unchanged from the factory default of compatibility. 7.1.4.3 Capacity clip to 32GB The figure below shows the jumper positions used to select Device 0, Device 1, Cable Selection, or Device1 (Slave) Present while setting the drive capacity down to 32 GB for the purpose of 16383...

Specifications - Page 61

... 0 (Device 0). • When CSEL is open or at E-F. Deskstar 7K80 Hard Disk Drive Specification 57 To enable the CSEL mode (Cable Selection mode) the jumper block must be installed at a high level, the drive address is SET FEATURES (subcommand 07h). These jumper settings are used for limiting power supply current when multiple drives are used. 2. Refer to spin up is 1 (Device 1).

Specifications - Page 64

... of 80GB and 40GB models Power supply current of the drive power connector. RMS) ...drives must be held by the drive (referred to the ground of 40 GB and 80 GB models(PATA) (values in a user system frame which has no electrical level difference at drive...2.5 4.0 9.7 6.8 0.9 0.7 7.3.3 Power supply generated ripple at drive power connector Table 46: Power supply generated ripple at the four ...

Specifications - Page 100

...set of 6.4 GB besides flagged media defects not visible by setting the device maximum LBA to contain critical system data such as if it . Shipping of the current setting....drive manufacturer When the drive is used to 12,692,735 (C1ACFFh) via conventional methods. Returned value shows that native device maximum LBA is as BIOS code within the protected area. Deskstar 7K80 Hard Disk Drive...

Specifications - Page 101

... device is in the protected area is in the Set_Max_Frozen mode. Deskstar 7K80 Hard Disk Drive Specification 97 Read information data from the Set_Max_Locked mode to be used for normal use of the Set Max Unlock command. When the password is set . Advanced usage using this command is accepted, the device is in the Set_Max_Locked mode. Make entire...

Specifications - Page 105

... to allow the host to sequence the spin-up of a jumper. The IDENTIFY DEVICE information indicates the states as a result of powering up into Standby. 10.12 Power-Up in Standby feature set The Power-Up In Standby feature set allows devices to be powered-up into active state Deskstar 7K80 Hard Disk Drive Specification 101

Specifications - Page 108

...0, Sector 1, LBA 0, to the entire drive. Upon entering offset mode the capacity of the nonvolatile protected area established using the Set Max Address command. Max LBA in offset mode... If a nonvolatile protected area has not been established before and after Set Feature Deskstar 7K80 Hard Disk Drive Specification 104 10.15 Address Offset Feature Computer systems perform initial code ...

Specifications - Page 142

...Word 66 67 68 69-74 75 76-79 80 81 82 Content 0078H 00F0H 0078H 0000H 00xxH 0000H 00FCH ...Set 9 (=0) DEVICE RESET command 8 (=0) SERVICE interrupt 7 (=1) Release interrupt 6 (=1) LOOK AHEAD 5 (=1) WRITE CACHE 4 (=0) PACKET Command feature set 3 (=1) Power management feature set 2 (=0) Removable feature set 1 (=1) Security feature set 0 (=1) SMART feature Set Deskstar 7K80 Hard Disk Drive...

Specifications - Page 143

... 14 NOP command 13 READ BUFFER command 12 WRITE BUFFER command 11 Reserved 10 Host Protected Area feature set 9 DEVICE RESET command 8 SERVICE interrupt 7 RELEASE interrupt 6 LOOK AHEAD 5 WRITE CACHE 4 PACKET Command feature set 3 Power management feature set 2 Removable media feature set 1 Security feature set 0 SMART feature set Deskstar 7K80 Hard Disk Drive Specification 139

Specifications - Page 145

Deskstar 7K80 Hard Disk Drive Specification 141 Table 91: Identify device information (Part 6 of 7) Word Content ...0=not detect 3 Device diag. 1=pass 0=fail 2-1 How to determine the device number 00=Reserved. 01=Jumper. 10=CSEL signal. 11=Some other method. 8 Shall be set to one if Dev 1. 7-0 Device 0 H/W reset result 7 Reserved 6 Respond for Enhanced security erase completion...

Specifications - Page 199

... go to (word 85 or 129) in Sector Count register as default. FFH C0-FEh 80-BFh 01-7Fh 00H Aborted The lowest Power Saving Mode is Normal Idle mode (the same ...Set Features command (with Feature register = 02h) without error, the write cache function will automatically be disabled. For the current write cache function status, refer to Low RPM standby mode) Deskstar 7K80 Hard Disk Drive...

Specifications - Page 201

... or disabling of Automatic Acoustic Management and the current Automatic Acoustic Management level setting across all forms of reset, that is 42h (= Enable Automatic Acoustic Management), the Sector Count Register specifies the Automatic Acoustic Management level. Deskstar 7K80 Hard Disk Drive Specification 197 12.37.4 Automatic Acoustic Management When Feature register is , Power on...