Hitachi DH24PC3 Support Question
Hitachi DH24PC3 Support Question
Find answers below for this question about Hitachi DH24PC3 - 15/16" SDS Plus Rotary Hammer 3 Mode.Need a Hitachi DH24PC3 manual? We have 2 online manuals for this item!
Question posted by jmelche on July 27th, 2013
The Drill Bit For My Hitachi Dh24pc 3 Doesn't Click In The Head.can't Be Attache
The person who posted this question about this Hitachi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hitachi DH24PC3 Manual Pages
Instruction Manual - Page 3
... or may cause machine damage. Most accidents that must be avoided by HITACHI. Hazards that result from power tool operation and maintenance are caused by the failure to prevent bodily injury or ... Manual before it occurs, and by WARNINGS on the power tool and in this Instruction Manual. NEVER use this power tool in a manner that has not been specifically recommended by recognizing...
Instruction Manual - Page 6
... tool bit with its own cord. NEVER place your hands, fingers or other than those specified in the Instruction Manual. 10. Don't use circular saw for applications other than those specified. NEVER use power tools if the plastic housing or handle is cracked. Handle tool correctly. ALWAYS attach the side handle and securely grip the Rotary Hammer...
Instruction Manual - Page 9
... the power tool. NAME OF PARTS
Depth gauge
Nameplate
Drill bit Front cap
Grip Side handle
Push button
Change lever
Push button Fig. 1
Switch
Housing Stopper Handle
SPECIFICATIONS
Motor Power Source Current Capacity
No-Load Speed Full-load Impact Rate Weight
Single-Phase, Series Commutator Motor
Single-Phase, 120V 60Hz
7.0A
Concrete:
1/8" ~ 15/16" (3.4mm...
Instruction Manual - Page 10
...is used, it may cause overheating, resulting in the ON position, the power tool will start operating immediately and can cause serious injury. 3. Contact a licensed electrician ...AND OPERATION
APPLICATIONS
Rotation and hammering function ⅜ Drilling anchor holes ⅜ Drilling holes in concrete ⅜ Drilling holes in tile
Rotation only function ⅜ Drilling in the OFF position.
If...
Instruction Manual - Page 11
... cup or dust collector (B) (Optional accessories) (Fig. 4, Fig. 5) When using tools such as bull points, drill bits, etc., make sure to the drill bit a shown in a twisting manner
into the tool holder until it to
prescribed precautions.
6. English
5. NOTE:
Drill bit
When using a rotary hammer for upward drilling operations attach a dust cup or dust collector (B) to collect dust or...
Instruction Manual - Page 12
... is pulled more than 7-15/32" (190 mm) of bit rotation
(Fig. 6)
R
The bit rotates clockwise (viewed from
the rear side) by attaching to drill bits which is pulled. English...rotary hammer on condition which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length. ⅜ Dump particles after every two or three holes when drilling. ⅜ Please replace the drill bit...
Instruction Manual - Page 13
..., the bit will stop immediately
and the rotary hammer will not only reducing drilling
efficiency at all , but will deteriorate the tip edge of the drill bit and reduce the
service life of SDS-plus shank is the
same as follows. Installing
Fig. 9
drill chuck and chuck adaptor (Fig. 10): (1) Attach the drill chuck to the drilling position (Fig. 8) (3) Pushing the rotary hammer forcibly...
Instruction Manual - Page 14
... and striking function
with the drill chuck and chuck adaptor attached. For withdrawing, it , the thread of slotted-head screws. (2) Driving in the rotation and striking function with chuck adaptor (D) and bit attached.
5. Apply the bit to the screw head grooves and gently drive the screws into the holes. ⅜ After rotating the rotary hammer at low speed for...
Instruction Manual - Page 15
...the hole and tighten the knob bolt securely. 8.
Hammering only This rotary hammer can be set to hammering only mode by pressing the push button and turning the change lever...16) (3) Turn the switch ON, and drill a hole in prescribed depth. How to use the drill bit (taper shank) and the taper shank adaptor. (1) Mount the taper shank adaptor to the rotary hammer. (Fig. 16) (2) Mount the drill bit...
Instruction Manual - Page 16
... to the rotary hammer. (Fig. 19)
(3) Insert the center pin into the slot of the taper shank adaptor and strike the head of the core bit shank to facilitate disassembly.
(2) Mount the core bit shank to turn power OFF and discon- Core bit Core bit shank
Thread
Fig. 18
Fig. 19 16 English
(4) To remove the drill bit (taper shank...
Instruction Manual - Page 17
...from the rotary hammer and strike the head of the rotary hammer.
Core bit shank Fig. 22
17
Center pin Core bit
Guide plate Core bit tip
Fig...16" (5 mm) in depth the position of the hole will deteriorate the tip edge of the drill bit, resulting in the center pin. English
(4) Engage the guide plate with the hammer holding the core bit, then the thread becomes loose and the core bit...
Instruction Manual - Page 18
... it can be performed by a Hitachi Authorized Service Center, ONLY.
18 How to replace grease Low viscosity grease is applied to this rotary hammer with this tool should ONLY be used with loosen screws is the very "heart" of wear from the
receptacle during maintenance and inspection.
1. Inspecting the drill bits Since use .
English
MAINTENANCE AND...
Instruction Manual - Page 19
... List will be
carried out by a Hitachi Authorized Service Center. Accordingly, some parts (i.e. MODIFICATIONS: Hitachi Power Tools are constantly being improved and modified to the Hitachi Authorized Service Center when requesting repair or other maintenance. B: Code No. Used D: Remarks CAUTION: Repair, modification and inspection of power tools, the safety regulations and standards...
Instruction Manual - Page 20
The use with your tool. Drilling anchor holes (Rotation + Hammering)
⅜ Drill Bit (Slender shaft)
(1) Drill Bit (Slender Shaft)
(2) Adaptor for slender shaft (SDS-plus shank)
Outer diameter 1/8"
(3.4 mm) 9/64"
(3.5 mm)
(1) Drill Bit (Slender Shaft)
Effective Length 1-25/32" (45 mm) 1-25/32" (45 mm)
Overall Length 3-35/64" (90 mm) 3-35/64" (90 mm)
Code No. 306369 ...
Instruction Manual - Page 21
... with a rotary hammer
Impact Drill
Application
Straight shank Bit
1/2" (13 mm) Hammer Drill Chuck (SDS-plus shank)
External dia. 7/16"
(11 mm) 1/2"
(12.3 mm) 1/2"
(12.7 mm) 9/16"
(14.3 mm) 9/16"
(14.5 mm) 11/16"
(17.5 mm) 7/8"
(21.5 mm)
Code No. 944460 944461 993038 944462 944500 944463 944464
Cotter (Code No. 944477)
Taper mode Code...
Instruction Manual - Page 23
.... 303625 303626 303627
Guide plate
Core bit (outer diameter) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm)
Code No.
982686 982687 982688
Core bit (outer diameter) 1-3/4" (45 mm)
2" (50 mm)
Code No.
982689 982690
4. Demolishing operation (Hammering only) Bull point (Round type) (SDS-plus shank) Code No. 303046
Bull point (Square type) (SDS-plus shank)
Center pin -
(A)
(B)
Code No...
Instruction Manual - Page 24
... 303045)
8. Bolt placing operation with Chemical Anchor. (Rotation + Hammering)
( ) Standard socket
on the market
(SDS-plus shank) Code No. 316658
6. English
5. Grooving (Hammering only) Grooving chisel (SDS-plus shank)
Code No. 321814
Code No. 303623
Chuck wrench 24 Drilling holes and driving screws (rotation only) ⅜ Drill chuck, chuck adaptor and chuck wrench
Special screw...
Instruction Manual - Page 25
...
into steel or wood).
10. 9. No.2 No.3
Screw Size 1/8" ~ 3/16" (3 - 5 mm) 1/4" ~ 5/16" (6 - 8 mm)
11. Drilling holes (rotation only)
English
Drill chuck (13VLD-D) Chuck adaptor (D)
(includes chuck wrench) (SDS-plus shank) Code No. 303624
Phillips Driver Bit
Bit No. Hammer grease A 1.1 lbs (500 g) (in a can) Code No. 980927 0.15 lbs (70 g) (in a green tube) Code No. 308471 0.07 lbs...
Parts List - Page 5
..., CAN
OPTIONAL ACCESSORIES
ITEM NO. USED
REMARKS
601 981-840 GREASE (A) FOR HAMMER. DESCRIPTION
NO.
HAMMER DRILL (30G) 1
602 308-471 GREASE FOR HAMMER. SCREW (A) (LEFT HAND) M6X25 1
618 321-813 DRILL CHUCK 13VLD-D
1
619 971-511Z + DRIVER BIT (A) NO. 2 25L
1
620 971-512Z + DRIVER BIT (A) NO. 3 25L
1
621 944-477 COTTER
1
622 982-684 CENTER PIN...
Parts List - Page 6
...
1
675 303-625 CORE BIT SHANK (SDS PLUS) 25-38MM 105L 1
676 303-626 CORE BIT SHANK (SDS PLUS) 25-38MM 300L 1
677 303-627 CORE BIT SHANK (SDS PLUS) 45-90MM 300L 1
678 303-624 CHUCK ADAPTER (D) (SDS PLUS)
1
679 321-825 DRILL CHUCK AND ADAPTER SET
1 INCLUD. 680
680 303-623 CHUCK ADAPTER (G) (SDS PLUS)
1
681 306-369 DRILL BIT (SLENDER SHAFT) D3.4X90...
Similar Questions
I Was Given The Above Cordless Driver Drill But Without Any Drill Bits. I Know I
I know it takes a Phillips bit (No. 2x55L)(code No. 318236). Is there other drill bits that I should...
I know it takes a Phillips bit (No. 2x55L)(code No. 318236). Is there other drill bits that I should...
(Posted by swimmer1946 2 years ago)
Hitachi Keyless Chuck Removal: Hitachi D10-vh
I have an Hitachi D10-VH 3/8" corded drill with keyless chuck and I wish to remove the keyless chuck...
I have an Hitachi D10-VH 3/8" corded drill with keyless chuck and I wish to remove the keyless chuck...
(Posted by detcord 3 years ago)
The Chuck On My Dh30pc2 Now Longer Grabs The Drill , Do I Need To Replace ?
the chuck on my DH30PC2 now longer grabs the drill bits, do I need to replace the whole thing and ho...
the chuck on my DH30PC2 now longer grabs the drill bits, do I need to replace the whole thing and ho...
(Posted by colinhsmith 11 years ago)
How Do I Secure A Drill Bit To My Hitachi Wh14daf2?
I am trying to secure my drill bit to my Hitachi WH14DAF2, but the only bits that sit securely are t...
I am trying to secure my drill bit to my Hitachi WH14DAF2, but the only bits that sit securely are t...
(Posted by fire1321 11 years ago)