Hitachi CC14SF Support Question

Find answers below for this question about Hitachi CC14SF - Power Tools 14'' Heavy-Duty Cut-Off Saw.
Need a Hitachi CC14SF manual? We have 2 online manuals for this item!

Hitachi Overview Questions Manuals Reviews Videos Research

Question posted by peterfranklin on May 15th, 2012

Operating Manual.

Can anyone please suply an operation manual for the Hitachi CC14SF cut-off machine, thanks.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TVDan on May 15th, 2012 8:14 PM

This answer was accepted by the poster of the original question.

TVDan

Member since:
August 8th, 2011

Points: 4,732,000

1,100
points

http://www.hitachipowertools.ca/upload/fmproduct_filec/CC14SF_OM_7739.pdf

TV Dan

Related Hitachi CC14SF Manual Pages

Instruction Manual - Page 3

...by WARNINGS on the power tool and in this power tool. Hazards that must be avoided by recognizing a potentially hazardous situation before operating or maintaining this Instruction Manual. MEANINGS OF SIGNAL WORDS WARNING indicates a potentially hazardous situations which , if not avoided, may result in minor or moderate injury, or may cause machine damage. CAUTION indicates a potentially...

Instruction Manual - Page 4

... 14. Always keep tools ...cutting operation produces dust. 11. ALWAYS DISCONNECT THE TOOL before servicing and before inserting the power plug into the receptacle. 4 ALWAYS REMOVE ADJUSTING KEYS, WRENCHES AND STOPPER BEFORE STARTING TOOL. ALWAYS MAINTAIN TOOLS WITH CARE. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. ALWAYS USE THE RIGHT TOOLS. Also, use power tools...

Instruction Manual - Page 5

... ACCESSORIES ONLY, WHEN OPERATING THIS TOOL. NEVER STAND ON TOOL. Check all components are not damaged. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED; Apply AC 120 volts only to the vise; Always wear snug-fitting clothing, non-skid footwear (preferably with the cut -off the power and wait for use on this instruction manual for residential use...

Instruction Manual - Page 6

... extension cords are in the Instruction Manual. 5. English 12. Always handle the cut -off wheel during cutting operation. 19. Never reach around or behind the cut -off wheel to move a plugged-in POWER TOOL while your hair is on and off wheel, while the tool is cracked or deformed. 14. Never abuse the power cord of the wheel guards are...

Instruction Manual - Page 7

... outer frame handled by a Hitachi authorized service center. otherwise they might dissolve. 7 DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this manual is wider than the other than accessories or carbon brushes. * Clean the exterior of the cut-off wheel. 3. POLARIZED PLUGS To reduce the risk of the POWER TOOL. Although this system has no...

Instruction Manual - Page 8

English SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL! 8

Instruction Manual - Page 9

.... 2 Screw handle Chain Item Model CC 14SF Type Protected type, series commutator motor Motor Power source Voltage Single-phase AC 60Hz 120 Volts Full-load current 15 Amp Type Reinforced resinoid cut-off wheel Cut-off wheel Dimensions Outside Dia 14" (355 mm) Thickness 7/64" (2.8 mm) Hole Dia. 1" (25.4 mm) Max. Width 4-11/64...

Instruction Manual - Page 10

... down to the main body) 2 Hex. WARNING: Never connect this manual may be hazardous. cord length Wire gauge size A.W.G (mm2) power loss and overheating. Determine from the handle. 10 Repair or replace as needed, before using the power tool. English STANDARD ACCESSORIES 2 1 Cut-Off Wheel 14" × 7/64" × 1"(355 × 2.8 × 25.4 mm) 1pc. (Code...

Instruction Manual - Page 11

.... Although it is of cracks or other visible damages. 4. Ensure that specified on the cut -off wheel breaks during operation of the tool. WARNING: When the clamping bolt is securely fastened with the trigger switch turned ON, the power tool will start suddenly and could be damaged when the wheel axle starts revolving, causing a hazardous...

Instruction Manual - Page 12

... for deflection to confirm that no operating abnormalities exist before attempting a cutting operation. When the cutting job is faulty. 10. otherwise vibration might occur and cause an accident. Repair or replace the receptacle, if it , step away from the front position and start the power tool and confirm that the power plug fits properly in the electrical...

Instruction Manual - Page 13

... removing. 3. On the contrary, too much pressure may be necessary to turn OFF the switch to prevent inadvertent operation of the motor and/or decreased cutting efficiency. 13 To operate the power tool, it in overload of the power tool. WARNING: Always remove the lock-off button fits rather tightly, it may result in a secure place, after...

Instruction Manual - Page 14

...cut is excessively wide, the vise can be set in two steps The vise jaws open to 6-11/16" (170 mm) while the vise can be effectively used by the chain line, after unscrewing the two bolts. screw of the vise jaws. Fig. 10 14...angles (Fig. 7 and 8). Cutting at the maximum of 0°, 30° or 45° as shown in Fig. 9. 5. The machine permits cutting at angles of 45° ...

Instruction Manual - Page 15

... power tool is fixed when the stopper has been lowered. q Tighten the bolt so that the stopper has returned to prevent accidental injury. 1. Using a Metallic Block (Fig. 11). Hex. Mounting the Cut-Off Wheel. English 6. Stopper (1) Press the stopper and loosen the bolt with a hex. CAUTION: q Confirm that it doesn't come loose during operation...

Instruction Manual - Page 16

... component of carbon brush Code No. 5/8" (16 mm) Wear Limit 1/4" (6 mm) Brush cap Brush holder Fig. 13 Fig. 14 3. WARNING: Never operate the power tool if any loose part. Consequently, re-dress or replace a dull cut-off wheel to prevent personal injury. 4. Therefore, inspect the brushes periodically, and replace them when they will slide smoothly...

Instruction Manual - Page 17

... points: *Rotary portion of shaft. *Rotary portion of vise. *Rotary portion of Hitachi Power Tools must be carried out by an AUTHORIZED HITACHI POWER TOOL REPAIR CENTER, ONLY. Service parts list CAUTION Repair, modification and inspection of vise-jaw. *Quick vise. 7. In the operation and maintenance of wear from normal use. Accordingly, some parts (i.e. SERVICE AND REPAIRS...

Instruction Manual - Page 51

... × 20 501 HEX. SOCKET HD.BOLT M10 × 20 12 WASHER (A) 13 WHEEL WASHER (A) 14 CUT-OFF WHEEL ASS'Y 16 MACHINE SCREW M5 × 12 17 SPRING WASHER M5 18 COVER BUSH 19 WHEEL COVER (A) 20 HITACHI LABEL 21 BOLT WASHER M5 25 BOLT WASHER M10 26 SPINNDLE ASS'Y 27 BALL BEARING 6306ZZCM...

Parts List - Page 1

Hitachi Power Tools LIST NO. E708 ELECTRIC TOOL PARTS LIST CUT-OFF MACHINE Model CC 14SF 2005 • 9 • 22 (E1) 5 4 3 2 1 501 20 18 19 18 87 16 5 21 23 7 22 1 5 A 7 6 8 15 13 14 10 9 13 12 11 35 31 6 32 34 33 26 29 30 28 27 53 58 57 56 55 54 B 46 63 62 61...

Parts List - Page 2

...14 CUT-OFF WHEEL 355MM 1 * 15 325-120 DESIGN COVER 1 FOR SAF 16 949-237 MACHINE SCREW M5X12 (10 PCS.) 4 * 18 325-127 COVER BUSH 2 EXCEPT FOR CHN 19 325-105 WHEEL COVER (A) 1 * 20 HITACHI..., AUT, FIN, DEN, SWE, NOR, GBR, SUI, AUS, NZL * 6 307-294 MACHINE SCREW (W/WASHERS) M5X16 (BLACK) 2 * 6 307-294 MACHINE SCREW (W/WASHERS) M5X16 (BLACK) 1 FOR SAF, CHN * 7 325-130 BOLT (A) (W/FLANGE...

Parts List - Page 3

... 340-643F STATOR ASS'Y 230V-240V 1 INCLUD. 41, 44 FOR IND, KUW 44 998-744 BRUSH TERMINAL 2 45 325-116 BEARING BUSHING 1 46 312-298 MACHINE SCREW (W/WASHERS) M5X35 7 47 NAME PLATE 1 48 325-125 HOUSING ASS'Y 1 INCLUD. 45, 49, 50 49 938-477 HEX. HD. CODE NO. 37 600-0VV...

Parts List - Page 4

... PCS.) 1 FOR SAF * 89 949-434 BOLT WASHER M10 (10 PCS.) 1 FOR SAF CC 14SF STANDARD ACCESSORIES ITEM NO. CODE NO. USED 601 949-012 CUT-OFF WHEEL 355MM (10 PCS.) 1 REMARKS --- 4 --- * ALTERNATIVE PARTS Printed in Japan 9 -- 05 (050922N) SOCKET HD. USED 501 955-857 HEX. BOLT (W/WASHERS) M8X25 2 73 968...