Hitachi DH30PC2 Support Question
Hitachi DH30PC2 Support Question
Find answers below for this question about Hitachi DH30PC2 - 1 3/16 Inch SDS.Need a Hitachi DH30PC2 manual? We have 2 online manuals for this item!
Current Answers
Answer #1: Posted by kcmjr on August 8th, 2011 12:45 PM
kcmjr
Member since:
May 5th, 2011 Points: 4,254,255
Member since:
May 5th, 2011 Points: 4,254,255
Get it here: http://hitachi.imvoi.com/power-tool/dh30pc2.html
Licenses & Certifications: Microsoft, Cisco, VMware, Novell, FCC RF & Amateur Radio licensed.
Related Hitachi DH30PC2 Manual Pages
Instruction Manual - Page 3
...be avoided by recognizing a potentially hazardous situation before operating or maintaining this Instruction Manual and in the sections which contain the operation and maintenance instructions. An accident can...and operating instructions in the Instruction Manual before it occurs, and by WARNINGS on the power tool and in this Instruction Manual. English
IMPORTANT SAFETY INFORMATION
Read and ...
Instruction Manual - Page 4
..., or long hair can cause you are doing and use common sense when
operating a power tool. Work Area
(1) Keep your hair, clothing and gloves away from a receptacle. Double Insulation eliminates... clothing or jewelry.
Cluttered benches and dark areas
invite accidents.
(2) Do not operate power tools in the
presence of flammable liquids, gases, or dust. Distractions can be caught in a...
Instruction Manual - Page 5
... to bind and are easier to a rotating part of this manual. Keep cutting tools sharp and clean. Many accidents are caused by poorly maintained tools. (8) Use only accessories that are dangerous in tools that have the tool serviced before plugging in a risk of untrained users. (6) Maintain tools with the switch is designed. (3) Do not use only...
Instruction Manual - Page 6
... those specified. NEVER touch moving parts. 7. Use right tool. Handle tool correctly. NEVER touch the tool bit with a "live" wire will make exposed metal parts of the tool. 8. NEVER place your hands, fingers or other than those specified in the Instruction Manual. 10. NEVER operate this tool without all guards or safety features in place and...
Instruction Manual - Page 7
...arrange for dust build-up frequently.
15. no .......... NEVER leave tool running unattended. Confirm before use a tool which is defective or operating abnormally. Alternating current
7 Definitions for symbols..., thinner benzine, carbon tetrachloride, and alcohol may burn out.
16. Turn power off. Should a power tool be careful with soapy water and dry thoroughly.
20. ALWAYS be...
Instruction Manual - Page 8
... keep the double insulation system effective, follow the normal electrical safety precautions given in this power tool, and only genuine HITACHI replacement parts should disassemble or assemble this Instruction Manual, including not using the power tool in wet environments.
"Double insulation" means that two physically separated insulation systems have been used to insulate...
Instruction Manual - Page 9
...
Single-Phase, Series Commutator Motor
Single-Phase, 120V 60Hz
7.4A
Concrete:
5/32" - 1-3/16" (4mm - 30mm)
Steel: Wood:
1/2" (13mm) 1-1/4" (32mm)
0 - 850/min.
0 - ... The information contained in this Instruction Manual is designed to assist you in this Instruction Manual may show details or attachments that differ from those on the tool unless you have first read and ...
Instruction Manual - Page 10
... overheating, resulting in a serious hazard.
10 WARNING:
Damaged cord must be replaced or repaired.
4. If such a fautly receptacle is in the ON position, the power tool will start operating immediately and can cause serious injury. 3. Tightening machine screws, wood screws (with optional accessories).
Contact a licensed electrician to a receptacle while the switch...
Instruction Manual - Page 11
NOTE:
When using tools such as bull points,
drill bits, etc., make sure to collect dust or particles for up- ...Use the dust cup by our
company.
(1) Clean the shank portion of the drill bit. (2) To attach a drill bit (SDS-plus
shank
Front cap
To prevent accidents, make sure to use the
Drill bit
Grip
genuine parts designated by attaching to
prescribed precautions...
Instruction Manual - Page 13
... hammer from the drilled
hole. This would seriously
shorten the service life of every components of SDS-plus shank is the same as the drill bit.
tion with the main unit in
the ...stop immediately
and the rotary hammer will react to the chuck adaptor. (2) The part of the SDS-plus
adaptor shank
CAUTION:
Fig. 7
Application of force more than necessary will not only reducing ...
Instruction Manual - Page 16
... the rotary hammer. (Fig. 15)
(3) Insert the center pin into the guide plate until it faces downward. (Fig. 16)
Fig. 14 Fig. 15
Center pin Core bit
Guide plate Core bit tip
Fig. 16 16
English
9. Using the side handle When you hold the machine with the center pin and the core bit...
Instruction Manual - Page 17
... is installed in reduced service life of the core bit shank strongly two or three times with the manual hammer holding the core bit, then the thread becomes loose and the core bit can be removed.
.... Connect all over the surface of the core bit tip and start operating. (3) When boring about 3/16" (5 mm) in depth the position of the hole will deteriorate the tip edge of the drill bit...
Instruction Manual - Page 18
... loosen screws is extremely
dangerous.
3. English
MAINTENANCE AND INSPECTION
WARNING: Be sure to or near "wear limit", it could result in excess of the power tool. Inspecting the carbon brushes: (Fig. 19) The motor employs carbon brushes which are properly tightened. When they become damaged and/or wet with a carbon brush...
Instruction Manual - Page 19
... Hammer Grease A is full air-tight construction to protect against dust and to Fig. 1) Loosen the two set screws. 5. Service and repairs All quality power tools will be performed by a Hitachi Authorized Service Center, ONLY.
19 English
Replacing carbon brushes: (For parts name, refer to prevent lubricant leakage. After replacing the...
Instruction Manual - Page 20
... 1 (4) Dust Cup (Code No. 971787 1 (5) Syringe (Code No. 318085 1
20 B: Code No. C: No. ACCESSORIES
WARNING: ALWAYS use of any obligation on the part of power tools, the safety regulations and standards prescribed in each country must be observed. In the operation and maintenance of the HITACHI.
code numbers and/or design...
Instruction Manual - Page 21
... size
Overall Length Code No. Knock-in anchor (Hammering only)
Anchor Setter (for anchor setting) (SDS-plus shank)
English
Cotter (Code No. 944477)
External dia. 7/16"
(11 mm) 1/2"
(12.3 mm) 1/2"
(12.7 mm) 9/16"
(14.3 mm) 9/16"
(14.5 mm) 11/16"
(17.5 mm) 7/8"
(21.5 mm)
Code No. 944460 944461 993038 944462 944500 944463 944464
Taper mode...
Instruction Manual - Page 22
...SDS-plus shank)
Center pin - (A)
(B)
Code No. Core bit shank
- 982684
982685
1"(25 mm) 1-1/8" (29 mm) (A) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) 1-3/4" (45 mm)
2" (50 mm) (B) 2-9/16...mm) 302979
W 5/16" (8 mm) 10-1/4" (260 mm) 302978
W 3/8" (9.5 mm)
6-1/4" (160 mm)
10-1/4" (260 mm)
303622
302977
Anchor setting adaptor (for manual hammer)
Anchor size W1/4"
(6.3 mm) W5/16" (8 mm) W3...
Instruction Manual - Page 23
... shank) Code No. 316656
5. Grooving (Hammering only) Grooving chisel (SDS-plus shank) Code No. 316659
English
23 Guide plate
Core bit (outer diameter) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) 1-3/4" (45 mm)
Code No.
982686 982687 982688 982689
Core bit (outer diameter)
2" (50 mm) 2-9/16" (65 mm) 3-5/32" (80 mm) 3-17/32" (90...
Instruction Manual - Page 25
...: Specifications are subject to change without any obligation on the part of the HITACHI.
25
Driving Screws (Rotation only)
Bit No. No.2 No.3
Screw Size 1/8" - 3/16" (3 - 5 mm) 1/4" - 5/16" (6 - 8 mm)
Length 1" (25 mm) 1" (25 mm)
11. Chuck adaptor (D) (SDS-plus shank) Code No. 303624
English
Phillips Driver Bit
Bit No. 10.
Parts List - Page 6
... ANCHOR SETTING ADAPTER A W1/4" (MANUAL) 1
656 971-795 ANCHOR SETTING ADAPTER A W5/16" (MANUAL) 1
657 971-796 ANCHOR SETTING ADAPTER A W3/8" (MANUAL) 1
658 971-797 ANCHOR SETTING ADAPTER A W1/2" (MANUAL) 1
659 971-798 ANCHOR SETTING ADAPTER A W5/8" (MANUAL) 1
660 971-799 ANCHOR SETTING ADAPTER B W1/4" (MANUAL) 1
661 971-800 ANCHOR SETTING ADAPTER B W5/16" (MANUAL) 1
662 971-801 ANCHOR...
Similar Questions
Hand Arm Vibration Syndrome Expoture Limit - 9 Inch Grinder
Can you provide Hand arm vibration syndrome expoture limit - 9 inch grinder?
Can you provide Hand arm vibration syndrome expoture limit - 9 inch grinder?
(Posted by RejeshKannan 9 years ago)
How It Works Hitachi Model Nr90ae
(Posted by skleofricp 10 years ago)
The Chuck On My Dh30pc2 Now Longer Grabs The Drill , Do I Need To Replace ?
the chuck on my DH30PC2 now longer grabs the drill bits, do I need to replace the whole thing and ho...
the chuck on my DH30PC2 now longer grabs the drill bits, do I need to replace the whole thing and ho...
(Posted by colinhsmith 11 years ago)
What Oil Should I Use For The Hitachi H90se - 1-1/8 Inch Hex 70lb
(Posted by steveb882 12 years ago)
Is This Tool Sold In America Or Is It A 230v Saw Only
(Posted by vernonhrdw 14 years ago)