Home » Hayward » Pool & Spa » Hayward Variable Speed Pump

Hayward Variable Speed Pump Support Question

Find answers below for this question about Hayward Variable Speed Pump.
Need a Hayward Variable Speed Pump manual? We have 2 online manuals for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by Skhosla30 on July 28th, 2016

Display Readswarning No Comm

We lost power for a couple hrs but when it came back the whole pool system was down . The electrician changed the gfi as that was not working .. Now the control panle works but the pump is not making any noice . If u reset the breaker it reads Warning no comm for a split second and then goes away.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by BusterDoogen on July 28th, 2016 8:26 AM

This answer was accepted by the poster of the original question.

BusterDoogen

Member since:
October 30th, 2011

Points: 28,565,407

1,100
points

Interference With Home Automation/Power Line Communication Equipment:

1. Make sure the terminal board connections agree with the wiring diagram on the pump data plate label.

2. Check for and correct any improper or loose wiring connections.

3. Install noise filter (from home automation/power line communication equipment vendor) to prevent equipment interference.

I hope this is helpful to you!

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Hayward Variable Speed Pump Manual Pages

Owners Manual - Page 4

... and spas if so marked. It can also make consumers aware of the motor. CAUTION - THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, AND SAFE USE OF THIS VARIABLE SPEED PUMP THAT MUST BE FURNISHED TO THE END USER OF THIS PRODUCT. Closely supervise children at all instructions in this electrical equipment, turn power supply...

Owners Manual - Page 5

..., contact a licensed electrician for information on how to the following entrapment hazards (symbols complements of swimming pool, spa, or hot tub. IMPORTANT - Suction Entrapment Hazard. A limb inserted into an opening of the body or limbs can result in a mechanical bind or swelling of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev...

Owners Manual - Page 6

... pump, fully open position. Do not change filter control valve position while pump ...pump controls must be set in off . WARNING - Fire and burn hazard. WARNING - Hazardous Pressure. Do not close filter manual air relief valve until a steady stream of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev-2 WARNING - Before servicing pool and spa...

Owners Manual - Page 7

... pool and spa control platforms, without issue 2.3. General Information 2.1. Given this manual MUST be mounted in four different positions on the pump or removed and mounted on the wall  No-rib, extra large basket design ensures easy debris removal and extends time between cleanings  Motor drive includes built-in Watts. The EcoStar Variable Speed Pump displays power...

Owners Manual - Page 9

...OFF power to pump before connecting to not exceed the maximum flow rate. Page 9 of a swimming pool ...Pumps, filters, and other equipment/ components of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev-2 NOTE - The pump...pump suction inlet and any plumbing fittings (elbows, valves, etc.). Electrical WARNING - Ground and bond pump before working...

Owners Manual - Page 10

... circuit breaker sizes. Bonding will connect all metal parts of swimming pool, spa, or hot tub. 4.9. Bonding reduces the risk of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev-2 All electrical wiring MUST conform to reinforcing rod or mesh. Speed Range: 600-3450 rpm (1000-3450 rpm for Canada] solid copper...

Owners Manual - Page 15

... 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev-2 Connection wire must be rated for wiring connection to display and motor drive board taking care to note the wire colors and corresponding numbers next to instructions provided in the Hayward pool control configuration menu. Preset Speeds 1-4 and Quick Clean are disabled when the...

Owners Manual - Page 16

... HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev-2 When Inputs 1-3 are activated via the pool control relays, timer speeds 1-8 are NOT software compatible. In addition to the lower "COMBUS" or wall mount "DISPLAY" data terminals. 5.4. Preset Speeds 1-4 and Quick Clean are disabled when the pump is remotely controlled. Filter pump relay plus 1 auxiliary relays...

Owners Manual - Page 18

... using the + and - Do NOT add chemicals to tighten cover. See filter owner's manual for pump to prime, which can be quickly updated using filter manual air relief valve. Turn on power and wait for more details. 4. CLOSE VALVES in front of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev-2 a.

Owners Manual - Page 19

... EcoStar Variable Speed Pump IS3401VSP Rev-2 Status LEDs: The CHECK SYSTEM LED will illuminate when the pump is a mode intended for use when the pool will illuminate once timers have been programmed to change parameters. 3. Stop/Resume: This button is not presently running. 4. The LED beside the button will scroll through 4) 4. Menu Outline 1. Speed Selection c. Set COMM Bus...

Owners Manual - Page 21

... or Relay Control Move to the automatic restart by a third party control using relay ...COMM Bus Address +- Enable or Disable Low Temp Operation Move to prime at the maximum allowed speed for pump Pool Filter Move to next menu item Note: The pump can be set the pump to next menu item 14. Page 21 of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump...

Owners Manual - Page 24

... allow the pump to alert the user that all bathers should exit the pool during normal operation, the above message is displayed to run at the Max Allowed Speed set in ... REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP Rev-2 Comm Bus Online (Addr: 1) Display showing COMM Bus communication status between the motor drive and Hayward control. 10. The pump will stop within several...

Owners Manual - Page 25

... in your pool/spa system. Do NOT use water to hose off every two seconds as possible. Use ONLY propylene glycol as necessary.  Hayward pumps have self-... Seal Change Instructions" in the system. ATTENTION - To avoid condensation/corrosion problems, do NOT cover or wrap pump with risk of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump IS3401VSP...

Owners Manual - Page 30

... Drive Display Cover 5 27 SPX3400DR2 Motor Drive Wiring Cover 5 - Pentair Water Pool & Spa, Inc. Description No. Page 30 of Pentair Water Pool & Spa, Inc., which is used herein for existing WHISPERFLO pump installations. Ctn. SPX3400DRKIT Wall Mount Kit 5 * WHISPERFLO is a registered trademark of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS EcoStar Variable Speed Pump...

Owners Manual - Page 36

... YOUR WARRANTY ON-LINE AT WWW.HAYWARDPOOL.COM New Installation Installation for: In Ground Spa Replacement and EcoStar are registered trademarks of Pool: Concrete/Gunite Vinyl Fiberglass Other Pool Capacity U.S. EcoStar Variable Speed Pump Warranty Card Registration Please Print Clearly: Years Pool has been in service First Name Last Name 1 year 1-3 4-5 6-10 11-15 >15 Street...

Technical Guide - Page 17

... used to run at a pre-determined speed for a certain length of the pump to edit when in a specific setup menu. User Interface PRESET SPEEDS 4 buttons that can be programmed to change the parameters. Default settings: Speed 1 1000 RPM 29% Speed 2 1750 RPM 51% Speed 3 2500 RPM 72% Speed 4 3250 RPM 94% Display Screen Fig 30 MENU/NAVIGATION BUTTONS The...

Technical Guide - Page 33

... programmed. Holding down the speed button for 3 seconds after adjusting speed will add the preset speed time up to 12 hrs maximum. TIMERS ACTIVE LED LED will raise or lower the speed. Even if the pump is an error condition. Unprotected mode requires manual verification. PRESET SPEEDS Any time one of the pump to the maximum set in...

Technical Guide - Page 43

... com link between VSC and Hayward control. Status of both drive and display. Press the Menu button until the Diagnostic screen appears (fig 83). These are the different screens and their meaning. Below are all real-time displays. This menu provides important information about the performance of the pump that has elapsed since the...

Technical Guide - Page 48

... on the comm. It travels on , the pump will ramp up and down in speed. Check input wiring and breaker. Disconnect Blue, Black, and Red motor leads (page 4) from the display and re-connect. Troubleshooting/Fault Codes Code/Fault Indications Warning NO Comm Inspect the data wire between the control and EcoStar. Control reads "Pool bridge comm" This indicates...

Technical Guide - Page 49

... on in Standalone mode. The pump comes on control display. wires between the pump interface and the control Check to make sure the Min and Max setting on the EcoStar comm. Be sure they are made to the GL/Hayward control. The EcoStar should be wired to operate with the settings in the control (page 20) EcoStar reverts to...