Hayward Pro Series Top-Mount Support Question
Hayward Pro Series Top-Mount Support Question
Find answers below for this question about Hayward Pro Series Top-Mount.Need a Hayward Pro Series Top-Mount manual? We have 4 online manuals for this item!
Question posted by fbaerga on March 14th, 2012
Backwash Leak While Filtering
The filter is leaking thru the backwash while filtering
Current Answers
Related Hayward Pro Series Top-Mount Manual Pages
Models: S220T S244T - Page 1
... if ignored presents a potential hazard.
A
MODELS S180T, S210T, S220T, S244T PRO™ SERIES HIGH-RATE SAND FILTERS
Basic safety precautions should always be alert to the potential for one of actions ... INSTRUCTION MANUAL
Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm)
HAYWARD POOL PRODUCTS, INC.
620 Division Street Elizabeth, NJ 07207 Tel: 908-351-5400 WWW.HAYWARDPOOL.COM ...
Models: S220T S244T - Page 2
...off position and filter manual air relief valve must be placed in such locations and distances to prevent their
being used in winterization of the pool/spa from near point to the pool by a ... test plugs and/or plugs used as described above .
CAUTION - Before servicing pool and spa circulation system, filters manual air relief valve must be damaged, broken, cracked, missing, or not ...
Models: S220T S244T - Page 3
...filter sand, dirt particles are in the backwash position, the water flow is directed to pool structure will produce clear, sparkling water with only minimal attention and care. Assemble pump and pump mounting...to pump per pump instructions.
Your Hayward Pro Series high-rate sand filter is loaded through your filter.
The pool water, which contains suspended dirt particles, ...
Models: S220T S244T - Page 4
...filter is rinsed out of Hayward Pool Products, Inc. This ensures that all suction and return lines are secure.
2. WASTE-To bypass filter for draining or lowering water level and for water leaks...Prime and start filter in FILTER position (not BACKWASH) to prevent clogging of the pool water it is now operating in the normal filter mode, filtering particles from the pool water, the ...
Models: S220T S244T - Page 6
... restrictions in intake and discharge lines.
3. partially drain & refill pool with water that has not been treated with Cyanuric Acid. Backwash filter.
Be sure Vari-Flo valve is sufficient.
3. PROBLEM SOLVING LIST
REMEDY
LOW WATER FLOW
1. POOL WATER WON'T CLEAR UP 1.
Check for air leak in pool and superchlorinate as required.
2. chlorine will naturally dissipate
CHLORINE...
Models: S220T S244T - Page 7
... implied warranty lasts, or the exclusion or limitation of purchase. Some states do not allow a limitation on these other conditions and terms of Pool
□ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater □ Heat Pump □ Salt/Chlorine Generator □ Controls
WWW.HAYWARDPOOL.COM
USE...
Model: S270T - Page 1
... only High Rate Sand No. ½ Silica Sand (.45mm - .55mm)
HAYWARD POOL PRODUCTS, INC.
620 Division Street Elizabeth, NJ 07207 Tel: 908-351-5400 WWW....or major property damage and if
ignored presents a potential hazard. B
MODEL S270T PRO™ SERIES HIGH-RATE SAND FILTER
Basic safety precautions should always be alert to hazards. OWNER'S MANUAL
INSTALLATION, OPERATION & PARTS
IS270T-05...
Model: S270T - Page 2
... described above . Suction outlets in filter upper body. o Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately. Failure to a large portion of 8
MODEL S270T
IS270T-05 Rev B
- Failure to keep suction outlet components clear of the pool/spa from near point to the pool by young children. Suction outlet components...
Model: S270T - Page 3
...dirt, the control valve is backwashed (cleaned) of time, the accumulated dirt in the filter causes a resistance to the top of filter sand, as specified on ...filter and piping system. Loosely pre-assemble both halves of operation.
Make electrical connections to filter tank. Your Hayward Pro Series high-rate sand filter is continuous and automatic and provides total recirculation of pool...
Model: S270T - Page 4
... heavy debris loads, set valve to waste.
This will permit algae and bacteria to grow in FILTER position (not BACKWASH) to RINSE. No returns may be made and are open), allowing the filter tank to the pool. Your filter system is clear-about 1/2 to RINSE position. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
Model: S270T - Page 6
... drain & refill pool with water that has not been treated with Cyanuric Acid. Check for restrictions in a safe and convenient location for algae in proper range (adjust as required.
2.
Check for debris.
2. Be sure flow rate through filter is set on "Filter" position.
Backwash filter. Check skimmer and pump strainer baskets for air leak in intake...
Model: S270T - Page 7
... reinstallation labor or any other conditions and terms of the standard warranty apply.
Filters which fail or become defective during the warranty period, except as a result... (1) year from Hayward:
Type of In-Ground Pool:
□ Vinyl □ Fiberglass □ Gunite
Size of Pool
□ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □...
Model: S310T - Page 1
... filter is automatically directed by the patented filter control valve to remove dirt particles from the bottom of pool water through your filter and piping system. INSTALLATION Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are trapped by your piping system and is backwashed (cleaned) of operation. Assemble pump and pump mounting...
Model: S310T - Page 3
... performed directly into 1/4" tapped hole in the normal filter mode, filtering particles from pool to the pump and filter and for normal filtering. To prevent damage to pool depending upon the pump and general piping system).
BACKWASH-For cleaning filter.
Loading sand media.
Sand surface should be open ), allowing the filter tank to fill with screwdriver handle to RINSE...
Model: S310T - Page 4
...your pool and make it difficult for continuous operation.
PROBLEM SOLVING LIST
REMEDY
LOW WATER FLOW
1. Backwash filter. Check...filter to pool).
4. POOL WATER WON'T CLEAR UP
1.
Check for crusting or caking (remove 1" of filter sand for air leak in U.S.A. SERVICE & REPAIRS Consult your pool size and usage. PLEASE REALIZE. . .
POOL CHEMISTRY GUIDELINES
SUGGESTED POOL...
Models: S310T2 S360T2 - Page 1
.... It can cause severe injury and/or death. B
MODELS S310T2, S360T2, PRO™ SERIES HIGH-RATE SAND FILTERS
Basic safety precautions should always be followed, including the following: Failure to follow ... INSTRUCTION MANUAL
Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm)
HAYWARD POOL PRODUCTS, INC.
620 Division Street Elizabeth, NJ 07207 Tel: 908-351-5400 WWW.HAYWARDPOOL.COM CAUTION...
Models: S310T2 S360T2 - Page 2
... supply. WARNING - Do not operate pool and spa circulation system unless filter manual air relief valve body is running . WARNING - Read and follow instructions can result in an increase potential for suction entrapment as described above .
o Dual suction fittings shall not be in an opening of the pool/spa from near point to remove pressure...
Models: S310T2 S360T2 - Page 3
...Pro Series high-rate sand filter is returned from the bottom of filter sand, as specified on a level concrete slab, very firm ground, or equivalent, as the permanent dirt removing media.
HOW IT WORKS
Your filter uses special filter sand to filter tank. The cleaned pool...Be sure the winter drain cap is poured in the backwash position, the water flow is automatically reversed through the ...
Models: S310T2 S360T2 - Page 4
...
base of the pool water it may be necessary to backwash frequently due to waste. Start pump and backwash until water in sight glass is 8-10 PSI (0.55-0.69 BAR) higher than the initial "clean" pressure you desire. WASTE-To bypass filter for draining or lowering water level and for water leaks and tighten connections...
Models: S310T2 S360T2 - Page 6
...
REMEDY
LOW WATER FLOW
1. Backwash filter.
chlorine will naturally dissipate
CHLORINE (STABILIZED) 1.0 to 70 ppm Add Stabilizer
Dilution - Be sure chlorine and pH levels are in intake and discharge lines.
3. Be sure Vari-Flo valve is sufficient.
3.
Check for air leak in pool and superchlorinate as required.
2. SHORT FILTER CYCLES
1. Operate filter for debris.
2. WWW...
Similar Questions
I Recently Lost Power, Now My Ecommand 4 Panel Will Not Turn My Pump On.
I can only turn the pump on and off with the panel breaker. The panel is no longer controlling the p...
I can only turn the pump on and off with the panel breaker. The panel is no longer controlling the p...
(Posted by karenmonroelvnv 9 years ago)
Hayward Sand Filter S220t Won't Backwash
(Posted by Terrykmkrazybou 9 years ago)
Instruction Manuel For Hayward Pro Series Model S244t
Where can i get a copy of the instruction manuel for the Hayward Pro Series Model S244T.?
Where can i get a copy of the instruction manuel for the Hayward Pro Series Model S244T.?
(Posted by mdobbinsdelreal 10 years ago)
How To Clean My Hayward Pro Series Model Number S-166t Sand Filter
(Posted by funngia 10 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)