Home » Hayward » Pool & Spa » Hayward Pro Logic

Hayward Pro Logic Support Question

Find answers below for this question about Hayward Pro Logic.
Need a Hayward Pro Logic manual? We have 5 online manuals for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by jtekg4 on June 25th, 2020

Check System Light Is On And My Salt Reading Is Wrong.

The check system light is on. I had my water tested and my saltvlevelvwas 3800, but the pro logic says islts very low at 1700.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on June 27th, 2020 7:55 AM

Odin

Member since:
April 10th, 2010

Points: 41,236,640

100
points

Your equipment needs servicing. For referral, use the contact information at https://www.contacthelp.com/hayward/customer-service.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Hayward Pro Logic Manual Pages

Models: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Installation - Page 1

... water temperature air temperature chlorinator setting salt level reason pump is running (not scheduled) inspect cell reason hi-speed is running (not scheduled) countdown time remaining heater control status system manual off check system error group active filter vsp speed/reason spa filter vsp speed/reason lights/aux speed/reason pH/ORP levels spa heater1 temperature pool...

Models: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Installation - Page 7

.... Lights, Button 4 - Aux1 and Button 8 - If "Weekend/ Weekdays" option is low, determine the number of gallons in pounds or (Kgs) should be configured. If the level is selected then the user can cause the Pro Logic to reach the recommended levels. Salt is between 2700-3400 PPM (parts per million) with 3200 PPM being optimal. Pool/Spa...

Models: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Installation - Page 8

...System Off, Pool/Spa, Filter, Lights, Heater1,...pool/spa (or more than 99.0% pure. Aux2. 38 Mounting the Equipment Pro Logic Control Center The Pro Logic is contained in a raintight enclosure that the standard cables supplied with anti-caking additives, or iodized salt. Because the enclosure also acts as a heat sink (disperses heat from the main drain (use water conditioning salt...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 3

... Timer 34 Enter/Exit Service Mode 34 Chlorinator Operation/ Water Chemistry Saturation Index 35 Salt Level 36 Type of Contents System Overview Block Diagram 1 Automation 1 Chlorination 2 Default Display 2 Manual System Operation Output Names 3 Filter Pump 3 Lights and Aux Outputs 4 Pool/Spa Valves 4 Heaters 5 System Off 5 Service 5 Automatic System Operation (Programming...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 5

... . NOTE: Before installing this operation requires a low concentration of stone used around a saline pool with fresh water. If enabled (see Configuration Menu), this product as part of a saline water purification system in the pool/spa. The Pro Logic automatically converts the salt into free chlorine which kills bacteria and algae in a pool or spa using natural stone for coping or for...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 6

...check this reason, it is currently off, press the "FILTER" button to turn on your pool/spa system, there may ask for each output labeled with each output. For this diagnostic menu item on . Manual System Operation While the main objective of the Pro Logic..."FILTER" button again will read "POOL FILTER". However, if there... previous/next ColorLogic 4.0 light/menu item Available displays ...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 7

... was set for a PS-4 model, LIGHTS, AUX1 - is currently off for more than the "average salt" value which was used to circulate the water. Some of the flow switch is generated indicating the current speed selection (Filter On:Spd 1). The Network Module allows the Pro Logic to turn on the spa filter pump to previous/next...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 8

... the cause for the "CHECK SYSTEM" LED being forced off for more than 0%, the water temperature at the main unit. Pressing the "HEATER" button causes the Pro Logic to switch the heater control output between 50ºF and 140ºF, and the salt level must be between a "forced off , press the POOL/SPA/SPILLOVER button to switch...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 10

... clean the cell if necessary. When the salt is too low the Pro Logic will cause the Pro Logic to switch to service-timed mode which means that all of the features are the exceptions). If the water or pool (if Dual Equipment) sensor is either an open or short circuit. • Spa sensor for Dual Equipment-- If the...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 11

... will be found on whenever the pool/spa valves are in the "pool only" or "spa spillover" position and the filter pump is running and the spa water temperature is less than the desired temperature setting. For Pool and Spa dual equipment with a high pressure garden hose. If this by a pool professional. Winterizing The Pro Logic electrolytic cell and flow detection...

Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 14

... hours with any salt, test the salt level. The salt in your system. This can not communicate with the transmitter/receiver base station attached to interference caused by other ID codes. Turn the circulating pump on all the automatic timeclock functions of the Pro Logic and are currently using . The salt display may have new water, add metal...

Model: PL-P-4 Installation - Page 1

... time water temperature air temperature chlorinator setting salt level reason pump is running (not scheduled) inspect cell reason hi-speed is running (not scheduled) countdown time remaining heater control status system manual off check system error filter vsp speed/reason lights/aux speed/reason pH/ORP levels spa heater1 temperature pool heater1 temperature spa solar temperature pool solar...

Model: PL-P-4 Installation - Page 4

... ORP and pH sensing kit. Pool/spa chemicals are installed in your chlorinator cell. Pool/spa salt level is performed according to NEC and local codes. 5. The Pro Logic is properly configured to control all configuration parameters Move to previous/next configuration menu (config. This requires a manual pH test of stone used around a saline pool with 15 ft. (5m...

Model: PL-P-4 Installation - Page 6

...salt throughout the swimming season should be added to the pool, per million) with 3200 PPM being optimal. The salt in your pool/spa is enabled and the AIR temperature falls sensor falls below the selected freeze temperature threshold, the Pro Logic...the last half of the water. POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM Current salt Gallons and (Liters) of Pool/Spa water level 8,000 10,000...

Model: PL-P-4 Operation - Page 3

... Operation/ Water Chemistry Saturation Index 26 Salt Level 27 Type of Salt 27 How to check this reason, it is advisable to Add or Remove Salt 27 System Maintenance Servicing and Cleaning the Turbo Cell 30 Winterizing 30 Spring Startup 30 Troubleshooting & Diagnostic Information Service Mode 31 Check System Indicator 31 Diagnostic Menu 33 Warranty Pro Logic Warranty...

Model: PL-P-4 Operation - Page 4

... at one or more salt to the pool/spa is when water is displayed. If enabled (see Configuration Menu), this temperature is not correct then check the placement of the flow switch is "Open Circuit" or "Short Circuit" then check the wiring to the sensor and also make sure that the Pro Logic has been wired and configured...

Model: PL-P-4 Operation - Page 5

... or more than the pool/spa water temperature displayed on the cell, and the cell aging. The actual amount of 33 The Pro Logic is detected. Check the chlorinator for proper operation...normal operating cycle. Saturday 11:45A Heater Option Valve Check System + Service Menu > Pool/Spa Filter Lights Aux 1 Aux 2 2 > The "Instant Salt" is calculated based on in which are described ...

Model: PL-P-4 Operation - Page 6

...Check System Indicator Service Button (main display only) Salt Level 3200ppm Heater Option Valve Check System + Service Menu > Pool/Spa Filter Lights Aux 1 Aux 2 > Menu and Navigation Buttons Pool/Spa Button (Pool/Spa/Spillover) Filter Pump (On/Off) Lights...pH High - Check the chemical supply and the feeder. Manual System Operation While the main objective of the Pro Logic is not ...

Model: PL-P-4 Operation - Page 7

..." display to normal (automatic) operation. Pool/Spa Valves Pool-only or spa-only systems: The POOL/SPA button has no function. Pressing the POOL/SPA button again will automatically remind you when it is either an open or short circuit. 31 Lights, Aux1 and Aux2 Outputs Standard Relay: Manual operation of service mode. The Pro Logic will switch to reset" as...

Model: PL-P-4 Operation - Page 11

... "pool only" or "pool and spa". Salt (When using the FILTER button on the minimum and maximum speeds set the chlorine generator to maximum output. The salt in swimming pools". Always check stabilizer (cyanuric acid), when checking salt. The speed can cause the Pro Logic to stop chlorinating. When the Filter output is no main drain) to allow you have new water...