Hayward Power-Flo Support Question
Hayward Power-Flo Support Question
Find answers below for this question about Hayward Power-Flo.Need a Hayward Power-Flo manual? We have 1 online manual for this item!
Question posted by HarryEvans on July 22nd, 2013
Hayward Power-flo Pump Sp125j
My pump has a lot of air coming from the port on the pool. What can I do about this problem?
Current Answers
Related Hayward Power-Flo Manual Pages
Model: ALL - Page 1
... and to the end
user of today's above-ground swimming pools. The advanced design reduces maintenance requirements while providing superior performance. C
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
Power-Flo LX™ / Power-Flo II™ Pump Series
The Hayward® Power-Flo LX™ and Power-Flo II™ Pump Series are UL-Listed. ISPF SERIES Rev.
Corporate Headquarters...
Model: ALL - Page 2
...to all metal parts of swimming pool, spa, or hot tub, and to all times. Do not install in a building such that components such as a means of air for cooling. Run wire from... pools. Bond motor to pool structure. Power-Flo LX™ / Power-Flo II™ Pump Series
PRODUCT REGISTRATION
(Retain For Your Records)
DATE OF INSTALLATION
INITIAL PRESSURE GAUGE READING (CLEAN FILTER
PUMP ...
Model: ALL - Page 3
... only. Power-Flo LX™ / Power-Flo II™ Pump Series __________
____________
NOTE: The National Electrical Code (NEC) permits use the pool or
spa if a drain cover is equipped with a cord complying with the NEC, the following three (3) items apply. Qualified personnel MUST do NOT use provided air relief valve to electric supply. If screws are lost...
Model: ALL - Page 4
.... For pipe larger than port, use a tool to prevent leakage.
Pump motors require free circulation of air for servicing pump and piping. Select a well...Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions
Pump Location
The Power-Flo LX™ pump MUST be installed below the pool water line (see Figure to two layers of tape.
Pump Mounting
Fasten pump...
Model: ALL - Page 5
Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions (cont.)
Fittings
Fittings restrict flow.
Do NOT ground to local codes and regulations. WARNING - NOTE: All electrical wiring MUST be permanently connected to pool structure. Permanently ground motor. Connect motor ground terminal to local or national electrical code requirements. Connect a No. 8 AWG (8.4 ...
Model: ALL - Page 6
... chemicals to suction pipe level. STOP PUMP before starting system. ƒ Release all air from filter and piping system. fill strainer and pump with water. ƒ Clean and lubricate strainer cover O-ring with water before proceeding. 2. Reset if necessary.
NOTE: If you do so with water to pool/spa system directly in suction and outlet...
Model: ALL - Page 7
... dangerous or fatal electrical shock hazard, turn OFF power to follow instructions may damage plastic components in a dry enclosure. Store pump in the system. Have a qualified
serviceman repair/replace wiring as possible.
To reduce risk of severe injury or death to base. 4. Contact your pool/spa
system.
Explosion Hazard. Drain all intake and output...
Model: ALL - Page 8
... use ). 3. Be sure motor base and pump discharge port are positioned properly. Reconnect pump to pool. Open all valves and make sure that the pump strainer housing is tight, tap lightly from the...motor shaft. Power-Flo LX™ / Power-Flo II™ Pump Series
Shaft Seal Change Instructions (cont.)
Exercise extreme care in handling both the skimmer outlet port and return port to the ...
Model: ALL - Page 9
... your pool dealer can confirm this
manual. Block off . iv. Check For:
1. Centrifugal switch stuck in the cover O-ring groove. If pump develops a vacuum, check for line blockage. backwash as per manufacturer's instructions; Holding hand over the bottom port with water and the cover O-ring is necessary. ƒ Keep motor clean. Power-Flo LX™ / Power-Flo...
Model: ALL - Page 10
... HP
----
SP1540C
Model No. No. Motor (for SW1585X20) - 2 HP
---- SPX1515Z1E
Motor (for SP1750) - 1/2 HP
----
---- Power-Flo LX™ / Power-Flo II™ Pump Series
Replacement Parts
Parts Diagram
Parts Listing
Ref.
on Original Equipment
7 Pump Housing
SPX1500AA
SPX1580AAP
8 Housing Nut, No. 10-24 Hex Head SPX1500Y2 (7 Req'd.) SPX1500Y2 (8 Req'd.)
Motor (for...
Model: ALL - Page 11
...
Please send me more information on how long an implied warranty lasts, or the exclusion or limitation of purchase, or to : Hayward Pool Products, Inc., 620 Division Street, Elizabeth, NJ 07207, Attn: Warranty Dept.
Power-Flo LX™ / Power-Flo II™ Pump Series
HAYWARD® LIMITED WARRANTY
This pump was inspected before shipment from our plant.
For further...
Similar Questions
Hayward Power Flo Sp125j...
Need replacement strainer housing....what's the part number
Need replacement strainer housing....what's the part number
(Posted by Anonymous-171724 1 year ago)
I Have A Power Flo Xl Pump . I Replaced The Owing On The Basket Top On The Pump
I have a power flo xl pump . I replaced the o-ring on the basket top on the puman it when the pump i...
I have a power flo xl pump . I replaced the o-ring on the basket top on the puman it when the pump i...
(Posted by Reallyneatdecks64 10 years ago)
Haward Power Flo Pump--model S48a85a04, Sp-1515-z1-ew,
Hello, I am trying to replace this above pump with basket. The problem I am seeing is that the outle...
Hello, I am trying to replace this above pump with basket. The problem I am seeing is that the outle...
(Posted by rjsviper22 10 years ago)
No Suction At Pool, Air Coming Out Of Manual Valve Slowly
been releasing air out of manual valve for a couple days now, still no suction. no apparent blockage...
been releasing air out of manual valve for a couple days now, still no suction. no apparent blockage...
(Posted by monsekitch 12 years ago)