Hayward Power-Flo Support Question
Hayward Power-Flo Support Question
Find answers below for this question about Hayward Power-Flo.Need a Hayward Power-Flo manual? We have 1 online manual for this item!
Question posted by Anonymous-171724 on June 30th, 2022
Hayward Power Flo Sp125j...
Need replacement strainer housing....what's the part number
Current Answers
Answer #1: Posted by SonuKumar on July 11th, 2022 8:05 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,619,310
Member since:
May 9th, 2021 Points: 16,619,310
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Hayward Power-Flo Manual Pages
Model: ALL - Page 1
... today's above-ground swimming pools.
WARNING - SAVE THIS INSTRUCTION MANUAL
HAYWARD POOL PRODUCTS, INC. Corporate Headquarters: 620 Division Street Elizabeth, NJ 07207
U.S.A: 1 Hayward Industrial Drive Clemmons, NC ... MANUAL
INSTALLATION, OPERATION, & PARTS
Power-Flo LX™ / Power-Flo II™ Pump Series
The Hayward® Power-Flo LX™ and Power-Flo II™ Pump Series are UL...
Model: ALL - Page 2
... for storage. It requires free circulation of access to the pool by young children. Power-Flo LX™ / Power-Flo II™ Pump Series
PRODUCT REGISTRATION
(Retain For Your Records)
DATE OF INSTALLATION
INITIAL PRESSURE GAUGE READING (CLEAN FILTER
PUMP MODEL HORSEPOWER
FILTER MODEL SERIAL NUMBER
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this product is...
Model: ALL - Page 3
... property damage. Power-Flo LX™ / Power-Flo II™ Pump Series __________
____________
NOTE: The National Electrical Code (NEC) permits use of a cord with only one (1) wall of the pool or spa. To reduce the risk of pump and suction outlets must be OPEN when
starting the filter system. Installation of electric shock replace damaged cord...
Model: ALL - Page 4
...Allow pump inlet height to be installed below the pool water line (see Figure to right). Pump ...strainer port.
Pump mount must be solid - It is reduced considerably; For pump suction on molded plastic components.
NOTE: Do NOT use Plumber's Pipe Dope as it rains. Place supports near pump.
Though the pump is designed for outdoor use, it is needed. Power-Flo LX™ / Power-Flo...
Model: ALL - Page 5
... Wiring
Pump MUST be performed by code. For size of swimming pool, spa, or hot tub. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions (cont.)
Fittings
Fittings restrict flow... copper bonding wire to the pressure wire connector provided on the motor housing and to all metal parts of swimming pool, spa, or hot tub, and to all electrical equipment, metal piping or...
Model: ALL - Page 6
.... ƒ Replace strainer cover on strainer housing; If pump does NOT prime within ten minutes, stop motor and determine cause. WARNING - Do NOT add chemicals to prevent dirt, bugs, etc., from entering.
Priming Pump
ƒ Open all valves before proceeding. 2. Small children using pool MUST always have close adult supervision.
CAUTION - Power-Flo LX™ / Power-Flo II™...
Model: ALL - Page 7
... bags. Gravity drain system as far as needed. 3. Failure to motor
before beginning shaft seal replacement. B. Contact your pool/spa
system. To avoid dangerous or fatal electrical shock hazard, turn OFF power to follow instructions may damage plastic components in a dry enclosure. C.
SAVE THESE INSTRUCTIONS Power-Flo LX™ / Power-Flo II™ Pump Series
Storage/Winterization...
Model: ALL - Page 8
... and replace on strainer 'C' clip and remove. Assemble the pump cover to the piping or hoses provided. Tighten screws alternately and evenly. 15. Check For:
1. If you have a timer, be certain it is positioned on impeller hub and remove it by pressing the white ceramic seat out of overheating. Power-Flo LX™ / Power-Flo II...
Model: ALL - Page 9
... to check by removing the skimmer basket and holding your pool dealer can confirm this
manual. Power-Flo LX™ / Power-Flo II™ Pump Series
Troubleshooting (cont.)
Motor Hums, But Does NOT Start - Make sure pump/strainer housing is necessary. ƒ Keep motor clean. You should be replaced, due to restricted or undersized suction line or leak...
Model: ALL - Page 10
... HP
---- Description
Model No. SPX1510Z2E)
Model No.
on Original Equipment
7 Pump Housing
SPX1500AA
SPX1580AAP
8 Housing Nut, No. 10-24 Hex Head SPX1500Y2 (7 Req'd.) SPX1500Y2 (8 Req'd.)
Motor (for SP1750) - 1/2 HP
----
---- Power-Flo LX™ / Power-Flo II™ Pump Series
Replacement Parts
Parts Diagram
Parts Listing
Ref.
Motor (for SP1540C) - 40 GPM
SPX1540Z1E...
Model: ALL - Page 11
...the standard warranty apply.
Pump housing/strainers which vary from defects in obtaining warranty replacements.
Hayward Pool Products, Inc. 620 Division Street...housing/strainer to the nearest authorized Hayward service center. Mail to the factory without the express written authorization of Hayward Pool Products, Inc.
Power-Flo LX™ / Power-Flo II™ Pump Series
HAYWARD...
Similar Questions
How To Replace The Strainer Housing On Hayward Power Flo Pool Pump
(Posted by gowthttja 10 years ago)
How To Install New Hayward Power-flo Strainer Housing
(Posted by Flmo 10 years ago)
Hayward Power-flo Pump Sp125j
My pump has a lot of air coming from the port on the pool. What can I do about this problem?
My pump has a lot of air coming from the port on the pool. What can I do about this problem?
(Posted by HarryEvans 10 years ago)
I Have A Power Flo Xl Pump . I Replaced The Owing On The Basket Top On The Pump
I have a power flo xl pump . I replaced the o-ring on the basket top on the puman it when the pump i...
I have a power flo xl pump . I replaced the o-ring on the basket top on the puman it when the pump i...
(Posted by Reallyneatdecks64 10 years ago)