Hayward Perflex Support Question
Hayward Perflex Support Question
Find answers below for this question about Hayward Perflex.Need a Hayward Perflex manual? We have 5 online manuals for this item!
Question posted by jkkeck on August 2nd, 2021
How Do
how do you remove a broken bump handle on an ec75a Hayward filte
Current Answers
Answer #1: Posted by SonuKumar on August 2nd, 2021 7:22 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,636,680
Member since:
May 9th, 2021 Points: 16,636,680
https://www.troublefreepool.com/threads/bump-handle-on-hayward-de-filter-broke.181825/
http://wetheadmedia.com/hayward-perflex-de-filter-repair-troubleshooting/
https://www.youtube.com/watch?v=FLpS3kWFRDE
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Hayward Perflex Manual Pages
Models: EC65A EC75A - Page 3
...broken, cracked, missing, or unsecured can result in an entrapment. o Never use Pool or Spa if any suction outlet component is , damaged, broken, cracked, missing, or unsecured can cause severe injury and/or death due to remove...ten years or if found to be damaged, broken, cracked, missing, or not securely attached. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, NC ...
Models: EC65A EC75A - Page 4
... information. The Hayward-Perflex is initially started; The Perflex filter uses diatomite...Perflex's exclusive "BUMP" action, the D.E. If the pump is designed for complete filter draining. Keep the filter bump handle, drain outlet, and pressure gauge accessible for changing the handle...remove dirt from the filter when it rains. For best pump performance, locate the system above , the pool...
Models: EC65A EC75A - Page 5
... (.49-.70 Bar) above the precoat pressure, regenerate the filter. TO CHANGE BUMP HANDLE POSITION
1. Remove the bump handle grip.
This completes the cleaning phase. The filter is suggested.
Repeat 3 times. Reinstall the bump cover and grip. When there is installed below the pool water line, close the suction and return valves) and
VACUUMING
Vacuuming can be...
Models: EC65A EC75A - Page 8
...D.E. coated with pool dirt, algae, 1. Clean.
2. Alternate would be added as soon as necessary. Electric motor running less than maximum
5. Consult pump and motor trouble
shooting guide. Bump-Drain-Recharge.
Regulate
4.
Page 8 of filter. D.E. Change to max.
Clean.
3. Air leak on return line.
1.
R.P.M. (under speed)
6. Bump handle bent.
4. Super...
Models: EC65A EC75A - Page 11
... $9.95* (+ $2.50 for shipping and handling) and mail to:
Hayward Pool Products Inc.
620 Division Street
Elizabeth, NJ 07207
Attn: Marketing Communications
DETACH HERE: Fill out completely and mail within 10 days of 1 lb. Hayward's D.E.
Hayward Pool Products has an easy, stress-free way for scooping out those hard-to your Perflex, plus vacuuming, preventative maintenance, and...
Perflex EC40 - Page 1
... the pool water line, for easy servicing.
2.
PUMP SELECTION
To power your Perflex filter, select a continuous duty pump designed for convenient operation. If the pump is designed for continuous operation, for installation above or below the water line for dependable priming. Self-priming pumps can drain by gravity. There is an alternate "BUMP" handle...
Perflex EC40 - Page 3
...). PREVENTIVE MAINTENANCE
While Perflex filters are recommended for a few seconds to flush out any dirt remaining in a pool increases every day as they can be harmful to 1 ratio; Refer to the pool.
Use only the swimming pool grades of 1 1/2" pipe. Open the filter drain and open when starting pressure. TO CHANGE BUMP HANDLE POSITION
1. Reinstall the...
Perflex EC40C90 Series - Page 2
...-ventilated location.
WARNING - A storable pool is constructed so that components such as a means of air for outdoor use, it is capable of swimming pool, spa, or hot tub, and to use...following: Failure to protect the electrical components from external bonding lug to the pool by young children. The Perflex™ Filtration System is designed for cooling. Run wire from the weather...
Perflex EC40C90 Series - Page 4
... day.
The Hayward Perflex D.E. filter provides the deepest, most efficient dirt remover known for installation below the pool water line. ...Bump" action makes it can run it fewer hours per hour. then drained from the pool water. filter, simply move the unique "Bump" handle up pressure and decreases the flow, conventional filters require backwashing. Through Perflex's exclusive "Bump...
Perflex EC40C90 Series - Page 5
... 1-1/2" pipe. Connect the pool return (inlet) plumbing.
8. Check for outdoor use . Install the system on the system are 1 ½" N.P.T. Keep the filter bump handle, drain outlet, and pressure...-end adapters. Perflex™ Extended Cycle Filtration System
Installation Instructions
System Location
For best pump performance, the system MUST be located below the pool water line (...
Perflex EC40C90 Series - Page 7
...removes dirt from the pool water, the accumulated dirt causes a resistance to do so could cause severe personal injury and/or property damage.
1.
Move the bump handle down slowly, then up briskly. Open the vent valve (under bump... has drained, and with water and repeat the "Cleaning" procedure. Perflex™ Extended Cycle Filtration System
Start-Up & Operation
Starting the Filter...
Perflex EC40C90 Series - Page 8
Perflex™ Extended Cycle Filtration System
Start-Up & Operation (cont.)
To Change Bump Handle Position
1. Do NOT mix chlorine and acid.
Chlorine will naturally dissipate No action - Remove the bump handle grip. Push in tab at base of Hayward Pool Products, Inc. Carefully pry the bump cover from its operating location and stored indoors. WARNING - Do NOT add water to...
Perflex EC40C90 Series - Page 9
Perflex™ Extended Cycle Filtration System
Troubleshooting
Problem Running at high pressures.
Overcharge of pool dirt, algae, etc. Bump
Remedy
Bump-Drain-Recharge.
coated with normal accumulation of return flow. Air leak on return line.
D.E. Bumping incorrectly. Bump handle bent.
Super-chlorinate; Short cycles. Change to : 1.
Skimmer basket clogged.
Consult...
Perflex EC50 - Page 1
...being used with a variety of Hayward bases and plumbing connections, or ...remover known. Self-priming pumps can lift water from durable, corrosion-proof materials, it possible to the pool...Perflex filter, select a continuous duty pump designed for dependable priming.
When the filter powder is totally used, the "BUMP" action makes it is an alternate "BUMP" handle location on -ground pools...
Perflex EC50 - Page 2
...TO CHANGE BUMP HANDLE POSITION
1. Carefully pry the bump cover from the pool water, the accumulated dirt causes a resistance to the alternate position and align the handle and the ...Hayward's EC-10SC. 2. Refer to empty completely. A drain plug is unnecessary and could cause severe personal injury and/or property damage. If desired however, drain piping may be a slight increase in broken...
Perflex EC50 - Page 3
...Bump Mechanism Cover Filter Head w/Vent Valve Filter Body w/Flow Diffuser Vent Valve w/O-Ring Thrust Washer Bump Handle Assembly Bump Handle Grip Pivot Pin Shoulder Screw Locknut Bump...Flow Controller
NO. or use Hayward's Jet-Action Cleaning Wand (...Perflex filters are basically resistant to the difficulties often encountered as a result of chemical build-up , etc.) without requiring removal...
Perflex EC50C90 Series - Page 4
... Hayward Perflex D.E. Instructions in a perfectly balanced, non-corrosive system. The Hayward Perflex System is initially started; then drained from a vertical to the filter, resulting in this truly versatile pump changes from the filter when it can run it possible to automatically activate the Flex-Tubes, repositioning the dirt and D.E. filter, simply move the unique "Bump" handle...
Perflex EC50C90 Series - Page 5
... is all local and national codes. All electrical connections should be located below the pool water line (See Figure to plastic threads, wrap the entire threaded portion of tape..., beginning at the suction and outlet ports is an alternate bump handle location on molded plastic components. Perflex™ Extended Cycle Filtration System
Installation Instructions
System Location
For...
Perflex EC50C90 Series - Page 7
... near the original flow and pressure. As the filter removes dirt from the retaining groove and slide the cover off will decrease.
After each vacuuming operation.
Perflex™ Extended Cycle Filtration System
Start-Up & Operation (cont.)
Pre-Coating
Scoop 5 lbs. (2.3 kgs.) of handle. Rotate the bump handle to empty completely. Repeat 3 times. The filter is...
Perflex EC50C90 Series - Page 9
... suction side of pool dirt, algae, etc. Bump. Pump strainer basket clogged. Clean. Alternate method would be to larger size fitting.
Electric motor running less than maximum R.P.M. (underspeed). Combination of D.E.
loaded to capacity with a stiff wire brush through the pump strainer opening will usually work. Bumping incorrectly. Slow down stroke - Bump handle bent. Pump output...
Similar Questions
Hayward Ec40ac Bump Handle Tension
I have a question. I replaced my diaphram gasket on my hayward perfles DE filter this year. I notice...
I have a question. I replaced my diaphram gasket on my hayward perfles DE filter this year. I notice...
(Posted by Stevo11758 1 year ago)
Above Ground Hayward Power-flo Matrix Pool Pump Skimmer Lid Removal How To
(Posted by fcbbsrvflp 10 years ago)
The Bump Handle Moves Up And Down Too Easily And Doesn't Regenerate The Filter.
I dissassembled and cleaned the filter. While dissassembled, the bump handle seemed to work, (It pus...
I dissassembled and cleaned the filter. While dissassembled, the bump handle seemed to work, (It pus...
(Posted by multimom2003 11 years ago)
Bump Handle Position In Running Mode
should the bump handle be in up or down position in normal filtration mode?
should the bump handle be in up or down position in normal filtration mode?
(Posted by lorimanushaw 12 years ago)