Hayward Perflex Support Question
Hayward Perflex Support Question
Find answers below for this question about Hayward Perflex.Need a Hayward Perflex manual? We have 5 online manuals for this item!
Question posted by Stevo11758 on May 26th, 2022
Hayward Ec40ac Bump Handle Tension
I have a question. I replaced my diaphram gasket on my hayward perfles DE filter this year. I noticed that I have resistance bumping the filter in the up position my no resistance in the down position. Up until I had to replace the gasket I had resistance in both directions. Is there a wrong way to install the gasket.
Current Answers
Answer #1: Posted by SonuKumar on May 26th, 2022 9:43 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
https://www.youtube.com/watch?v=FLpS3kWFRDE
https://www.manualslib.com/manual/1288849/Hayward-Perflex-Ec40ac.html?page=7#manual
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Hayward Perflex Manual Pages
Models: EC65A EC75A - Page 3
...position. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN www.haywardpool.com Body Suction Entrapment- A negative pressure applied to prevent their being used in winterization of the pool/spa...(not air or air and water) is discharged.
Before servicing pool and spa circulation system, filters manual air relief valve must be placed in such locations and ...
Models: EC65A EC75A - Page 4
... a piping union is used , the "BUMP" action makes it has an output rating of the filter outlet. Keep the filter bump handle, drain outlet, and pressure gauge accessible for swimming pool service.
If rigid return piping is recommended for complete filter draining. Tighten pump base mounting bolts, if loose.
4. A drain plug, with gasket, is advisable to protect electrical...
Models: EC65A EC75A - Page 5
... process. Use only the swimming pool grades of operating chemicals, D.E., and a pool
test kit. Open the suction and return valves (when used). As the filter removes dirt from the pool water, the accumulated dirt causes a resistance to the alternate position and align the handle and the head anchor holes. then move the bump handle down slowly, then up in...
Models: EC65A EC75A - Page 8
...output to larger size fitting. recharging
d. Page 8 of pool 1. dirt, algae, etc.
2. Clean.
2. loaded to :
1. brisk upstroke.
2.
muriatic acid solution (or filter
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN www.haywardpool.com Electric motor running less than maximum
5. Bump-Drain-
5. after proper b.
NOTE: Most motor problems are...
Models: EC65A EC75A - Page 11
...; No
Size of your Perflex
fitter, cleaning your spa. Perflex - It keeps
maintenance at a minimum and pool equipment at a maximum!
or 1/2 lb. Needless guesswork is the only scoop that keeps maintenance at a
minimum and pool enjoyment at a maximum! Pre-Measure Scoop doubles as a broadcaster for shipping and handling) and mail to:
Hayward Pool Products Inc.
620 Division Street...
Perflex EC40 - Page 1
... number of fittings to provide unions for use plastic male-end adapters. Keep the filter "BUMP" handle, drain outlet, and pressure gauge accessible for changing the handle position are recommended.
3. IS40AB-98
MODEL EC40 SERIES
The Perflex Model EC40 is a high performance swimming pool filter with an output rating of between 40 and 65 GPM (150-246 LPM...
Perflex EC40 - Page 3
... suggested valving. 5. This completes the cleaning phase. The filter is needed . Proceed as the filter has been precoated.
For fastest results, regenerate the filter before and after the diatomite has been added.
TO CHANGE BUMP HANDLE POSITION
1. Carefully pry the bump cover from the pool water, the accumulated dirt causes a resistance to get too high, the minerals will form...
Perflex EC40C90 Series - Page 2
... permanently installed
above -ground and on this product is capable of being used with storable pools. Closely supervise children at all metal parts of swimming pool, spa, or hot tub, and to its original integrity.
KEEP SAFETY LABELS IN GOOD CONDITION AND REPLACE IF MISSING OR DAMAGED. Do NOT use or climb on -ground...
Perflex EC40C90 Series - Page 4
...pools ƒ Clamp for the EC40AC model requires only two (2) nuts and bolts ƒ Power-Flo Matrix™ Series high-performance pump ƒ Quick-connect union ƒ Modular platform base
Perflex™ Filtration Performance Data
Model No.
The Hayward Perflex D.E. filter... filter, simply move the unique "Bump" handle up pressure and decreases the flow, conventional filters ...
Perflex EC40C90 Series - Page 5
... cause cracking of the fitting, beginning at the suction and outlet ports is an alternate bump handle location on the system are 1 ½" N.P.T. Connect the pool suction plumbing between the filter and pump.
7. Connect the pool return (inlet) plumbing.
8. Keep the filter bump handle, drain outlet, and pressure gauge accessible for cooling. Though the pump is designed for...
Perflex EC40C90 Series - Page 7
... NOT operate the filter for pre-coating.
As the filter removes dirt from the pool water, the accumulated dirt causes a resistance to do so could cause severe personal injury and/or property damage.
1. When the pressure rises 7-10 psi (.49-.70 Bar) above the pre-coat pressure, regenerate the filter.
then move the bump handle down slowly...
Perflex EC40C90 Series - Page 8
... ppm
Action Required to the alternate position and align the handle and the head anchor holes. After cleaning, thoroughly flush all affected parts with Cyanuric Acid. To guard against this, a yearly chemical cleaning (soaking) of Hayward Pool Products, Inc. OR use other commercial filter element cleaner mixed in place.
4.
Remove the bump handle grip. Use a plastic container and...
Perflex EC40C90 Series - Page 9
... line caused by small eyeball fitting.
Skimmer basket clogged.
Air leak on return line. Check cover gasket, hand knobs, hose, clamps, etc. Replace or tighten as needed. Undersized or improper wiring. 2. D.E.
Bump handle bent.
Presence of D.E.
Probable Cause D.E.
Bump. Alternate method would be to : 1. Note: Most motor problems are due to disassemble and clean...
Perflex EC40C90 Series - Page 12
... portion) in a safe and convenient location for a period of ONE (1) year from Hayward:
□ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater Hayward shall not be made directly to the nearest authorized Hayward service center.
To obtain warranty replacements or repair, defective components or parts should be repaired or...
Perflex EC50 - Page 1
... filter "BUMP" handle, drain outlet, and pressure gauge accessible for swimming pool service. Self-priming pumps can lift water from a lower level and prime automatically. PUMP SELECTION
To power your Perflex filter, select a continuous duty pump designed for convenient operation.
All plumbing connections on -ground pools, advises that will be positioned so as a means of the filter...
Perflex EC50 - Page 2
... the pump. To clean, first stop the pump; Connect pool return plumbing. 7. Tap the pivot pin in broken or damaged fittings. 4. The filter is completely normal. Additional tightening is the "precoat pressure." then, using Hayward's EC-10SC. 2. This completes the cleaning phase. TO CHANGE BUMP HANDLE POSITION
1. FILTERING
Filtration starts as soon as in the bottom of...
Perflex EC50 - Page 3
...Bump Mechanism Cover Filter Head w/Vent Valve Filter Body w/Flow Diffuser Vent Valve w/O-Ring Thrust Washer Bump Handle Assembly Bump Handle Grip Pivot Pin Shoulder Screw Locknut Bump Shaft O-Ring Retainer Filter Head Screw Filter Head Nut Washer Tube Sheet (Top or Bottom) Diaphragm Gasket... Perflex filters are basically resistant to a garden hose. or use Hayward's...this, a yearly chemical cleaning ...
Perflex EC50C90 Series - Page 2
... all electrical equipment, metal piping or conduit within 5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub, and to the pressure wire connector provided on the ground or in a damp or non-ventilated location. The Perflex™ Filtration System is designed for outdoor use, it cannot be readily disassembled for storage...
Perflex EC50C90 Series - Page 4
... hours per hour. It is a high performance swimming pool filter system having an output rating of the Hayward® Perflex™ Filtration System. Product Features
ƒ Designed for large above -ground pool pump.
filter unique. filter, simply move the unique "Bump" handle up pressure and decreases the flow, conventional filters require backwashing. It is driven by a heavy...
Perflex EC50C90 Series - Page 12
...Inc. To original purchasers of this Warranty Certificate (upper portion) in obtaining warranty replacements.
Perflex™ Extended Cycle Filtration System
HAYWARD® LIMITED WARRANTY
This filter system was inspected before shipment from Hayward:
□ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater Parts which...
Similar Questions
The Bump Handle Moves Up And Down Too Easily And Doesn't Regenerate The Filter.
I dissassembled and cleaned the filter. While dissassembled, the bump handle seemed to work, (It pus...
I dissassembled and cleaned the filter. While dissassembled, the bump handle seemed to work, (It pus...
(Posted by multimom2003 11 years ago)
Bump Handle Position In Running Mode
should the bump handle be in up or down position in normal filtration mode?
should the bump handle be in up or down position in normal filtration mode?
(Posted by lorimanushaw 11 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)