Home » Hayward » Pool & Spa » Hayward Max-Flo II

Hayward Max-Flo II Support Question

Find answers below for this question about Hayward Max-Flo II.
Need a Hayward Max-Flo II manual? We have 1 online manual for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by orgvil on May 15th, 2012

Motor Bearings

I need the motor bearing for this model, how can I get them? Model C48D32A04 SER 24109FM

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hayward Max-Flo II Manual Pages

All Max-Flo II models - Page 1

... GENUINE REPLACEMENT PARTS P/N: IS2700 REV. B OWNER'S MANUAL INSTALLATION, OPERATION, & PARTS Max-Flo II™ Pump Series *50HZ Models are not UL Listed. The Hayward Max-Flo II™ is an ideal choice for improved motor cooling and to avoid unnecessary service calls, read this manual. Designed for pools of all electrical installations noted in environments up to 122 degrees...

All Max-Flo II models - Page 2

...times. Components such as a means of the motor. Do not install in this owner's manual and on permanently installed swimming pools and may result in this product. This ...to hazards. To reduce risk of non-Hayward replacement parts voids warranty. Pool and spa components have a finite life. Max-Flo II ™ Series ____ ____ _____ _ Page 2 of being readily disassembled ...

All Max-Flo II models - Page 3

... AWG (8.4 mm2) solid copper bonding wire to the pressure wire connector provided on the motor housing and to all metal parts of electric shock, see installation instructions and consult a professional ...and CPSC guidelines, follow all electrical wiring MUST be installed a minimum of swimming pool, spa, or hot tub. Max-Flo II™ Series _____ _____ _____ _____ Page 3 of the body or limbs can ...

All Max-Flo II models - Page 4

... not operate pool and spa circulation system unless filter air relief valve body is in locked position in this manual MUST be OPEN when starting the circulation system. Never operate or test the circulation system at high temperatures and if they can cause fires, which could result in open position. Max-Flo II™ Pump...

All Max-Flo II models - Page 5

... Suction line diameter must : Allow pump inlet height to be as close to pool as practical and run suction lines as direct as possible to further reduce vibration ...advised to protect the electrical components from excess moisture and flooding. Keep motor clean. Be protected from the weather. Max-Flo II ™ Series__________ Product Specifications _____ Page 5 of piping (L as ...

All Max-Flo II models - Page 6

Max-Flo II ™ ... USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Electrical WARNING - Do NOT ground to motor nameplate voltage. Insure that the electrical supply available agrees with one to electrical... of Plumbing and Mechanical Officials (IAPMO) standards. Fittings Fittings restrict flow. Pool and spa fittings MUST conform to force hose connector fitting past this stop. Use a...

All Max-Flo II models - Page 7

...the Master On-Off switch. Max-Flo II ™ Series _ _________ _____ Page 7 of 16 Electrical (cont'd.) Voltage Voltage at motor MUST NOT be more than 110% of rated voltage when motor is running at a water ...wire required by fully opening filter manual air relief valve until a steady stream of swimming pool, spa, or hot tub, and to all parts to verify they are also on filter,...

All Max-Flo II models - Page 8

...motor bearings and shaft seals. fill strainer housing with plastic film or bags. NEVER run the pump dry. Separation Hazard. ATTENTION - To avoid condensation/corrosion problems, do so could result in your pool/spa... only a low pressure (below ). ATTENTION- Keep motor dry and covered during storage. See filter owner's manual. Max-Flo II ™ Series Page 8 of 16 Starting/Priming ...

All Max-Flo II models - Page 9

...& replace if necessary. Max-Flo II ™ Series Page 9 of the pump/strainer housing (item #4), exposing the diffuser(item #9). Disconnect all recesses & parts to tap seal out. Remove the motor end cover/canopy by ...rubber cup on page 11 of the spring seal, and remove it to the pool. 2. WARNING - NOTE - Removing the Impeller (See Parts Diagram on the ceramic...

All Max-Flo II models - Page 10

...housing (item#4), being careful not to disturb the diffuser gasket (item#8). 15. Slide the motor assembly with the matching holes in place, and lubricated. Note: Arrow on page 11 of... 14. Re-attach motor end cover/canopy by holding motor shaft with a clean, soft, cotton cloth. 11. Max-Flo II ™ Series Page 10 of the ceramic seat. Replacing the Motor Assembly (See Parts ...

All Max-Flo II models - Page 11

Max-Flo II ™ Series Replacement Parts Parts Diagram Page 11 of 16 Item #16: Optional with some models SEE PARTS LISTING ON NEXT PAGE www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

All Max-Flo II models - Page 12

... 1 (Single Phase, 60 Cycle 115/230V) SPX2715Z2M Motor, 2 HP, Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V) www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Part No. 1a SPX2700DLS Description Strainer Cover Kit (Includes Strainer Cover, Lock-Ring, O-Ring) Ctn. Max-Flo II ™ Series Parts Listing Page 12 of 16...

All Max-Flo II models - Page 13

...wiring diagram on pool wall. 3. You may be certain it is clean. b. Re-check strainer housing cover and all connections, circuit breakers, and fuses. ii. www.haywardpool.com... movement and lack of 16 Troubleshooting Motor Will NOT Start - You should have a timer, be the cause. Solution: Contact a qualified repair professional. Max-Flo II ™ Series Page 13 of ...

All Max-Flo II models - Page 14

... return fitting will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. Undersized pool piping. backwash as per manufacturer's instructions; Solution: Sand filters - D.E. Solution: Correct suction condition or throttle return lines, if practical. clean or replace cartridge. 4. Max-Flo II ™ Series Page 14 of filter, valve...

All Max-Flo II models - Page 15

... □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater □ Heat Pump □ Salt/Chlorine Generator □ Controls www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS removal and/or reinstallation labor or any other products from state to the nearest authorized Hayward service center. Max-Flo II ™ Series ___...

All Max-Flo II models - Page 16