Home » Hayward » Pool & Spa » Hayward Max-Flo II

Hayward Max-Flo II Support Question

Find answers below for this question about Hayward Max-Flo II.
Need a Hayward Max-Flo II manual? We have 1 online manual for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by gomaryos on December 22nd, 2011

Manual Hayward Vari Flo Valve Model 710

The person who posted this question about this Hayward product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hayward Max-Flo II Manual Pages

All Max-Flo II models - Page 1

... elevated base for improved motor cooling and to avoid unnecessary service calls, read this manual. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY. P/N: IS2700 REV. The Hayward Max-Flo II™ is an ideal choice for pools of non-Hayward replacement parts voids warranty. Designed for both new construction or as a replacement pump...

All Max-Flo II models - Page 2

...spa, adequate ventilation and free circulation of air must be in conformance with hot tubs and spas if so marked. www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Max-Flo II... professional. Failure to its original integrity. THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, ...air for use with storable pools. This product should be used with all...

All Max-Flo II models - Page 3

... installed a minimum of this manual. - Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately. - www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Run a.... Installation of electric shock, do NOT use pool or spa if any suction outlet component is recommended. Max-Flo II™ Series _____ _____ _____ _____ Page 3...

All Max-Flo II models - Page 4

...pool and spa circulation system if a system component is discharged. All suction and discharge valves MUST be followed precisely. The instructions in open filter manual air relief valve. Pool and spa ...the system, which may result in filter upper body. Max-Flo II™ Pump Series __________ _____ Page 4 of the Hayward Max-Flo IITM Series. Failure to minimize the risk for burns...

All Max-Flo II models - Page 5

...[90] [698] [2.44] www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Though the pump is strongly advised to water level as close to pool as practical and run suction lines as direct as shown to... valves in suction and discharge piping. It is recommended that will not flood when it is designed for outdoor use of piping (L as possible to reduce friction loss. Max-Flo II...

All Max-Flo II models - Page 6

... prevent leakage. www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS All plastic fittings must be in pool (multiple drains) or double suction (skimmer ...Pool and spa fittings MUST conform to two additional layers of 16 WARNING - Use copper conductors only. Pumps, filters, and other equipment/ components of Plumbing and Mechanical Officials (IAPMO) standards. Max-Flo II...

All Max-Flo II models - Page 7

...so could potentially cause electrical shock if grounded or shorted. Max-Flo II ™ Series _ _________ _____ Page 7 of 16 Electrical...-Up NOTE - www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Use green ground terminal provided under...manual air relief valve until a steady stream of swimming pool, spa, or hot tub. Use the load circuit breaker as filter air relief valve...

All Max-Flo II models - Page 8

... manual air relief valve after stopping the pump. Do NOT use water to starting pump after pump is non- Propylene glycol is primed. If water source is running. Keep motor dry and covered during storage. Occasionally, shaft seals must be replaced, due to wear or damage. Replace with genuine Hayward seal assembly kit. Max-Flo II...

All Max-Flo II models - Page 9

...-part replacement seal. Failure to the pool. 2. Contact your local authorized Hayward Dealer or service center if you have...of the ceramic facing out. 9. If tight, use this manual for pump component locations.) 3. C. Remove the motor end ...-type soap. Lubricate the rubber cup on the motor shaft). 5. Max-Flo II ™ Series Page 9 of the ceramic seal with a clean,...

All Max-Flo II models - Page 10

...snugly by using the two (2) hex shaped screws. Diagram 1 www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Gently wipe the black, polished surface of the spring seal assembly with the... Arrow on page 11 of this manual for pump component locations.) 14. Press the spring seal assembly (item #12) onto the motor shaft - Max-Flo II ™ Series Page 10 of the ceramic ...

All Max-Flo II models - Page 11

Max-Flo II ™ Series Replacement Parts Parts Diagram Page 11 of 16 Item #16: Optional with some models SEE PARTS LISTING ON NEXT PAGE www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

All Max-Flo II models - Page 12

... Shaft 1 (Single Phase, 60 Cycle 115/230V) SPX2715Z2M Motor, 2 HP, Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V) www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS No. Max-Flo II ™ Series Parts Listing Page 12 of 16 Ref.

All Max-Flo II models - Page 13

.../union connections. Leaking O-ring or packing glands on suction side. Solution: Tighten, repair, or replace valves. 4. b. Check impeller for free movement and lack of 16 Troubleshooting Motor Will NOT Start - Max-Flo II ™ Series Page 13 of obstruction. Manually check rotation of motor shaft for debris. Ensure o-ring is equipped with water. Improper or...

All Max-Flo II models - Page 14

...caused by restricted or undersized suction line or leak at once. © Hayward Pool Products, 2005 All rights reserved. Loose stones/debris hitting impeller could be ...Flow - filters - Air leak in pool, and unrestricted discharge return lines. D.E. Check For: 1. Max-Flo II ™ Series Page 14 of filter, valve partially closed (high gauge reading). Generally...

All Max-Flo II models - Page 15

... and convenient location for a period of ONE (1) year from Hayward: □ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater □ Heat Pump □ Salt/Chlorine Generator □ Controls www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Max-Flo II ™ Series ___ Page 15 of purchase, or to...

All Max-Flo II models - Page 16